Instrukcja obsługi Microchip MCP4023

Microchip Niesklasyfikowane MCP4023

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Microchip MCP4023 (74 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/74
2006-2017 Microchip Technology Inc. DS20001945F-page 1
MCP4021/2/3/4
Features
• Nonvolatile Digital Potentiometer in SOT-23,
SOIC, MSOP and DFN Packages
• 64 Taps: 63 Resistors with Taps to Terminal A and
Terminal B
• Simple Up/Down (U/D) Protocol
• Power-on Recall of Saved Wiper Setting
• Resistance Values: 2.1 k, 5 k, 10 k or 50 k
• Low Tempco:
- Absolute (Rheostat): 50 ppm (0°C to 70°C Typ.)
- Ratiometric (Potentiometer): 10 ppm (Typ.)
• Low Wiper Resistance: 75 (Typ.)
• WiperLock™ Technology to Secure the wiper
setting in nonvolatile memory (EEPROM)
• High-Voltage Tolerant Digital Inputs: up to 12.5V
• Low-Power Operation: 1 µA Max Static Current
• Wide Operating Voltage: 2.7V to 5.5V
• Extended Temperature Range: –40°C to +125°C
• Wide Bandwidth (-3 dB) Operation:
- 4 MHz (Typ.) for 2.1 k Device
Description
The MCP4021/2/3/4 devices are nonvolatile, 6-bit
digital potentiometers that can be configured as either a
potentiometer or rheostat. The wiper setting is
controlled through a simple Up/Down (U/D) serial
interface.
These device’s implement Microchip’s WiperLock
technology, which allows application-specific
calibration settings to be secured in the EEPROM
without requiring the use of an additional write-protect
pin.
Package Types
Block Diagram
Device Features
.
A
W
B
MCP4021
SOIC, MSOP, DFN
MCP4022
SOT-23-6
MCP4023
SOT-23-6
MCP4024
SOT-23-5
RheostatPotentiometer
Potentiometer Rheostat
A
VSS
W
1
2
3
4
8
7
6
5
VDD U/D
NC
B
CS
4
1
2
3
5W
CS
VDD
VSS
U/D
4
1
2
3
6A
CS
VDD
VSS
U/D
5W
AW
B
4
1
2
3
6A
CS
VDD
VSS
U/D
5W
A
W
W
A
B B
V
DD
VSS
U/D
W
B
(Resistor Array)
Wiper Register
CS
WiperLock
EEPROM and
A
2-Wire
Interface
and
Control
Logic
Power-Up
and
Brown-Out
Control
Technology
Device Wiper
Configuration
Memory
Type
Resistance (typical) # of
Steps
VDD
Operating
Range
Control
Interface
WiperLock
Technology
Options (k) Wiper ()
MCP4021 Potentiometer (1) EE 2.1, 5.0, 10.0, 50.0 75 64 2.7V - 5.5V U/D Yes
MCP4022 Rheostat EE 2.1, 5.0, 10.0, 50.0 75 64 2.7V- 5.5V U/D Yes
MCP4023 Potentiometer EE 2.1, 5.0, 10.0, 50.0 75 64 2.7V - 5.5V U/D Yes
MCP4024 Rheostat EE 2.1, 5.0, 10.0, 50.0 75 64 2.7V - 5.5V U/D Yes
Note 1: Floating either terminal (A or B) allows the device to be used in Rheostat mode.
Low-Cost NV Digital POT with WiperLock™ Technology
MCP4021/2/3/4
DS20001945F-page 2 2006-2017 Microchip Technology Inc.
1.0 ELECTRICAL
CHARACTERISTICS
Absolute Maximum Ratings †
VDD ............................................................................................................. 6.5V
CS and U/D inputs w.r.t V
SS...................................
–0.3V to 12.5V
A, B and W terminals w.r.t V
SS................... –0.3V to VDD + 0.3V
Current at Input Pins ..................................................±10 mA
Current at Supply Pins ...............................................±10 mA
Current at Potentiometer Pins ...................................±2.5 mA
Storage temperature ....................................–65°C to +150°C
Ambient temp. with power applied ...............–55°C to +125°C
ESD protection on all pins  4 kV (HBM), 400V (MM)
Maximum Junction Temperature (TJ) ..........................+150°C
† Notice: Stresses above those listed under “Maximum
Ratings” may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational listings of this specification is not implied.
Exposure to maximum rating conditions for extended periods
may affect device reliability.
AC/DC CHARACTERISTICS
Electrical Specifications: Unless otherwise indicated, all parameters apply across the specified operating ranges.
TA = –40°C to +125°C, 2.1 k5 k10 kand50 kdevicesTypical specifications represent values for V
DD = 5.5V, VSS = 0V,
TA = +25°C.
Parameters Sym Min Typ Max Units Conditions
Operating Voltage Range VDD 2.7 — 5.5 V
CS Input Voltage VCS VSS — 12.5 V The CS pin will be at one of
three input levels (VIL, V
IH or
VIHH). (Note 6)
Supply Current IDD — 45 — µA 5.5V, CS = V
SS, fU/D = 1 MHz
— 15 — µA 2.7V, CS = VSS, fU/D = 1 MHz
— 0.3 1 µA Serial Interface Inactive
(CS = VIH, U/D = VIH)
— 0.6 3 mA EE Write cycle, T
A = +25°C
Resistance
(± 20%)
RAB 1.68 2.1 2.52 k-202 devices( )Note 1
4.0 5 6.0 k-502 devices( )Note 1
8.0 10 12.0 k-103 devices( )Note 1
40.0 50 60.0 k-503 devices( )Note 1
Resolution N 64 Taps No Missing Codes
Step Resistance RS — RAB / 63 — Note 6
Note 1: Resistance is defined as the resistance between terminal A to terminal B.
2: INL and DNL are measured at V
W with VA
= VDD and VB = V
SS. (–202 devices V
A = 4V).
3: MCP4021/23 only, test conditions are: I
W = 1.9 mA, code = 00h.
4: MCP4022/24 only, test conditions are:
5: Resistor terminals A, W and B’s polarity with respect to each other is not restricted.
6: This specification by design
7: Non-linearity is affected by wiper resistance (R
W), which changes significantly over voltage and temperature. See
Section 6.0, "Resistor" for additional information.
8: The MCP4021 is externally connected to match the configurations of the MCP4022 and MCP4024, and then tested.
9: This parameter is not tested, but specified by characterization.
Device
Resistance
Current at Voltage Comments
5.5V 2.7V
2.1 k2.25 mA 1.1 mA MCP4022 includes V
WZSE
MCP4024 includes VWFSE
5 k1.4 mA 450 µA
10 k450 µA 210 µA
50 k90 µA 40 µA
2006-2017 Microchip Technology Inc. DS20001945F-page 3
MCP4021/2/3/4
Wiper Resistance (Note 3 Note 4, ) R
W— 70 125 5.5V
— 70 325 2.7V
Nominal Resistance Tempco  R/ T — 50 — ppm/°C T
A = –20°C to +70°C
— 100 — ppm/°C TA = –40°C to +85°C
— 150 — ppm/°C TA = –40°C to +125°C
Ratiometeric Tempco VWA/T — 10 — ppm/°C MCP4021 and MCP4023 only,
code = 1Fh
Full-Scale Error VWFSE -0.5 -0.1 +0.5 LSb Code 3Fh ( only)MCP4021/23
Zero-Scale Error VWZSE -0.5 +0.1 +0.5 LSb Code 00h (MCP4021/23 only)
Monotonicity N Yes Bits
Potentiometer Integral Non-linearity INL -0.5 ±0.25 +0.5 LSb MCP4021/23 only ( )Note 2
Potentiometer Differential
Nonlinearity
DNL -0.5 ±0.25 +0.5 LSb MCP4021/23 only ( )Note 2
Resistor Terminal Input Voltage Range
(Terminals A, B and W)
VA,VW,VBVss — VDD VNote 5, Note 6
Maximum current through A, W or B I
W— — 2.5 mA Note 6
Leakage current into A, W or B I
WL — 100 — nA MCP4021 A = W = B = VSS
— 100 — nA MCP4022/23 A = W = VSS
— 100 — nA MCP4024 W = VSS
Capacitance (P
A) CAW — 75 — pF f =1 MHz, code = 1Fh
Capacitance (P
w) CW— 120 — pF f =1 MHz, code = 1Fh
Capacitance (P
B) CBW — 75 — pF f =1 MHz, code = 1Fh
Bandwidth -3 dB BW — 4 — MHz -202
devices
Code = 1F,
output load = 30 pF
— 2 — MHz -502
devices
— 1 — MHz -103
devices
— 200 — kHz -503
devices
AC/DC CHARACTERISTICS (CONTINUED)
Electrical Specifications: Unless otherwise indicated, all parameters apply across the specified operating ranges.
TA = –40°C to +125°C, 2.1 k5 k10 kand50 kdevicesTypical specifications represent values for V
DD = 5.5V, VSS = 0V,
TA = +25°C.
Parameters Sym Min Typ Max Units Conditions
Note 1: Resistance is defined as the resistance between terminal A to terminal B.
2: INL and DNL are measured at V
W with VA = VDD and VB = VSS. (–202 devices V
A = 4V).
3: MCP4021/23 only, test conditions are: I
W = 1.9 mA, code = 00h.
4: MCP4022/24 only, test conditions are:
5: Resistor terminals A, W and B’s polarity with respect to each other is not restricted.
6: This specification by design
7: Non-linearity is affected by wiper resistance (R
W), which changes significantly over voltage and temperature. See
Section 6.0, "Resistor" for additional information.
8: The MCP4021 MCP4022 is externally connected to match the configurations of the and MCP4024, and then tested.
9: This parameter is not tested, but specified by characterization.
Device
Resistance
Current at Voltage Comments
5.5V 2.7V
2.1 k2.25 mA 1.1 mA MCP4022 includes VWZSE
MCP4024 includes VWFSE
5 k1.4 mA 450 µA
10 k450 µA 210 µA
50 k90 µA 40 µA

Specyfikacje produktu

Marka: Microchip
Kategoria: Niesklasyfikowane
Model: MCP4023

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Microchip MCP4023, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Microchip

Microchip

Microchip ATECC608B Instrukcja

7 Października 2024
Microchip

Microchip HV860 Instrukcja

7 Października 2024
Microchip

Microchip EVB-LAN9255 Instrukcja

7 Października 2024
Microchip

Microchip LX4580 Instrukcja

7 Października 2024
Microchip

Microchip LX7720 Instrukcja

7 Października 2024
Microchip

Microchip AT32UC3C0128C Instrukcja

4 Października 2024
Microchip

Microchip AT32UC3A3256 Instrukcja

4 Października 2024
Microchip

Microchip AT32UC3A364 Instrukcja

4 Października 2024
Microchip

Microchip AT32UC3B0256 Instrukcja

4 Października 2024
Microchip

Microchip AT32UC3A0512 Instrukcja

4 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024