Instrukcja obsługi Microchip dsPIC33EP64GP502

Microchip Niesklasyfikowane dsPIC33EP64GP502

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Microchip dsPIC33EP64GP502 (130 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/130

High-Speed PWM

Section 14. High-Speed PWM

HIGHLIGHTS

This section of the manual contains the following major topics:

14.1 Introduction .................................................................................................................. 14-2

14.2 Features....................................................................................................................... 14-2

14.3 Control Registers ......................................................................................................... 14-3

14.4 Architecture Overview................................................................................................ 14-24

14.5 Module Description .................................................................................................... 14-27

14.6 PWM Operating Modes.............................................................................................. 14-33

14.7 PWM Generator......................................................................................................... 14-71

14.8 PWM Trigger.............................................................................................................. 14-87

14.9 PWM Interrupts.......................................................................................................... 14-98

14.10 PWM Fault Pins ......................................................................................................... 14-99

14.11 Special Features ...................................................................................................... 14-105

14.12 PWM Output Pin Control...........................................................................................14-111

14.13 Immediate Update of PWM Duty Cycle ................................................................... 14-113

14.14 Power-Saving Modes............................................................................................... 14-114

14.15 External Control of Individual Time Base(s)............................................................. 14-114

14.16 Application Information ............................................................................................ 14-115

14.17 Register Map............................................................................................................ 14-126

14.18 Related Application Notes........................................................................................ 14-127

14.19 Revision History ....................................................................................................... 14-128

dsPIC33E/PIC24E Family Reference Manual

14.1 INTRODUCTION

This section describes the High-Speed Pulse-Width Modulator (PWM) module and its

associated operational modes. The High-Speed PWM module in the dsPIC33E/PIC24E

device family supports a wide variety of PWM modes and is ideal for power

conversion/motor control applications. Some of the common applications include:

• AC-to-DC converters

• DC-to-DC converters

• AC and DC motors: BLDC, PMSM, ACIM, SRM, etc.

• Inverters

• Battery chargers

• Digital lighting

• Uninterrupted Power Supply (UPS)

• Power Factor Correction (PFC) (e.g., Interleaved PFC and Bridgeless PFC)

14.2 FEATURES

The High-Speed PWM module consists of the following major features:

• Up to seven PWM generators, each with an individual time base

• Two PWM outputs per PWM generator

• Individual period and duty cycle for each PWM output

• Duty cycle, dead time, phase shift and frequency resolution equal to the system clock

source (TOSC)

• Independent fault and current-limit inputs for up to 14 PWM outputs

• Redundant Output mode

• Independent Output mode (this feature is not available on all devices)

• Push-Pull Output mode

• Complementary Output mode

• Center-Aligned PWM mode

• Output override control

• Special Event Trigger

• PWM capture feature

• Prescaler for input clock

• ADC triggering with PWM

• Independent PWM frequency, duty cycle and phase shift changes

• Leading-Edge Blanking (LEB) functionality

• Dead time compensation

• Output clock chopping

Note: This family reference manual section is meant to serve as a complement to device

data sheets. Depending on the device variant, this manual section may not apply to

all dsPIC33E/PIC24E devices.

Please consult the note at the beginning of the “High-Speed PWM” chapter in the

current device data sheet to check whether this document supports the device you

are using.

Device data sheets and family reference manual sections are available for

download from the Microchip Worldwide Web site at: http://www.microchip.com

Section 14. High-Speed PWM

High-Speed PWM

14.3 CONTROL REGISTERS

The following registers control the operation of the High-Speed PWM module:

•PTCON: PWM Time Base Control Register

- Enables or disables the High-Speed PWM module

- Sets the Special Event Trigger for the ADC

- Enables or disables immediate period updates

- Selects the synchronizing source for the master time base

- Specifies synchronization settings

•PTCON2: PWM Clock Divider Select Register 2

Provides the clock prescaler to the PWM master time base

•PTPER: Primary Master Time Base Period Register

Provides the PWM time period value

•STCON: PWM Secondary Master Time Base Control Registe (1)

- Enables or disables immediate period updates based on the secondary master time base

- Selects the synchronization source for the secondary master time base

- Specifies the synchronization setting for secondary master time base control

• STCON2: PWM Secondary Clock Divider Select Register 2(1)

Provides the clock prescaler to the PWM secondary master time base

•STPER: Secondary Master Time Base Period Register(1)

Provides the secondary master time base period value

•MDC: PWM Master Duty Cycle Register

Provides the PWM master duty cycle value

•SEVTCMP: PWM Special Event Compare Register

Provides the compare value that is used to trigger the ADC module

•SSEVTCMP: PWM Secondary Special Event Compare Register(1)

Provides the compare value that is used to trigger the ADC module based on the

secondary master time base

•CHOP: PWM Chop Clock Generator Register

- Provides the chop clock frequency

- Enables or disables the chop clock generator

•PWMKEY: PWM Unlock Register(1)

Writes the unlock sequence to allow writes to the IOCONx and FCLCONx registers

•PWMCONx: PWM Control Register

- Enables or disables fault interrupt, current-limit interrupt and primary trigger interrupt

- Provides the interrupt status for fault interrupt, current-limit interrupt and primary trigger

interrupt

- Selects the type of time base (master time base or independent time base)

- Selects the type of duty cycle (master duty cycle or independent duty cycle)

- Controls Dead Time mode

- Enables or disables Center-Aligned mode

- Controls the external PWM Reset operation

- Enables or disables immediate updates of the duty cycle, phase offset, independent time

base period

•IOCONx: PWM I/O Control Register

- Enables or disables PWM pin control feature (PWM control or GPIO)

- Controls fault/current limit override values

- Enables PWMxH and PWMxL pin swapping

- Controls the PWMxH and PWMxL output polarity

- Controls the PWMxH and PWMxL output if any of the following modes is selected:

• Complementary mode

• Push-Pull mode

• True Independent mode

Note: Not all registers are available on all devices. Refer to the “High-Speed PWM”

chapter in the specific device data sheet for availability.

Section 14. High-Speed PWM

High-Speed PWM

R/W-0 U-0 R/W-0 HS/HC-0 R/W-0 R/W-0 R/W-0 R/W-0

PTEN — PTSIDL SESTAT SEIEN EIPU(1) SYNCPOL(1) SYNCOEN(1)

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SYNCEN(1) SYNCSRC<2:0>(1) SEVTPS<3:0>(1)

bit 7 bit 0

Legend: HC = Cleared in Hardware HS = Set in Hardware

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 PTEN: PWM Module Enable bit

1 = PWM module is enabled

0 = PWM module is disabled

bit 14 Unimplemented: Read as ‘0’

bit 13 PTSIDL: PWM Time Base Stop in Idle Mode bit

1 = PWM time base halts in CPU Idle mode

0 = PWM time base runs in CPU Idle mode

bit 12 SESTAT: Special Event Interrupt Status bit

1 = Special Event Interrupt is pending

0 = Special Event Interrupt is not pending

bit 11 SEIEN: Special Event Interrupt Enable bit

1 = Special Event Interrupt is enabled

0 = Special Event Interrupt is disabled

bit 10 EIPU: Enable Immediate Period Updates bit(1)

1 = Active Period register is updated immediately

0 = Active Period register updates occur on PWM cycle boundaries

bit 9 SYNCPOL: Synchronize Input and Output Polarity bit

(1)

1 = SYNCIx/SYNCO polarity is inverted (active-low)

0 = SYNCIx/SYNCO is active-high

bit 8 SYNCOEN: Primary Time Base Sync Enable bit(1)

1 = SYNCO output is enabled

0 = SYNCO output is disabled

bit 7 SYNCEN: External Time Base Synchronization Enable bit(1)

1 = External synchronization of primary time base is enabled

0 = External synchronization of primary time base is disabled

bit 6-4 SYNCSRC<2:0>: Synchronous Source Selection bits(1)

These bits select the SYNCIx or PTGOx input as the synchronous source. Refer to the “High-Speed

PWM” chapter in the specific device data sheet for availability.

bit 3-0 SEVTPS<3:0>: PWM Special Event Trigger Output Postscaler Select bits

(1)

1111 = 1:16 postscaler generates Special Event trigger at every 16th compare match event

•

0001 = 1:2 postscaler generates Special Event trigger at every second compare match event

0000 = 1:1 postscaler generates Special Event trigger at every compare match event

Note 1: These bits should be changed only when PTEN = 0. In addition, when using the SYNCIx feature, the user

application must program the period register with a value that is slightly larger than the expected period of

the external synchronization input signal.

Specyfikacje produktu

Marka:	Microchip
Kategoria:	Niesklasyfikowane
Model:	dsPIC33EP64GP502

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Microchip dsPIC33EP64GP502, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Microchip

Microchip AT91SAM9M11 Instrukcja

15 Stycznia 2025

Microchip AT91SAM9261 Instrukcja

15 Stycznia 2025

Microchip AT91SAM9CN12 Instrukcja

15 Stycznia 2025

Microchip ATA5749C Instrukcja

15 Stycznia 2025

Microchip ATECC508A Instrukcja

15 Stycznia 2025

Microchip ATECC608C-TNGTLS Instrukcja

15 Stycznia 2025

Microchip ATECC608C-TCSM Instrukcja

15 Stycznia 2025

Microchip ATMXT144UD-SL Instrukcja

15 Stycznia 2025

Microchip ATMXT1296M1 Instrukcja

15 Stycznia 2025

Microchip ATMEGA162 Instrukcja

15 Stycznia 2025

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Rock N Roller R14G Instrukcja

29 Stycznia 2025

Rock N Roller R6RT Instrukcja

29 Stycznia 2025

QSC TSC-8 Instrukcja

29 Stycznia 2025

XTRARM XTR-FS5130 Instrukcja

29 Stycznia 2025

Sunding SD-581G Instrukcja

29 Stycznia 2025

XTRARM XTR-FS5070 Instrukcja

29 Stycznia 2025

XTRARM XTR-FS2010 Instrukcja

29 Stycznia 2025

Shimbol Memory I PRO Instrukcja

29 Stycznia 2025

OSEE TX402 Instrukcja

29 Stycznia 2025

GOgroove Record Cleaning Kit Instrukcja

29 Stycznia 2025