Instrukcja obsługi Microchip ATmega32U4

Microchip Niesklasyfikowane ATmega32U4

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Microchip ATmega32U4 (12 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/12

Differential and Single-Ended

ADC

Differential and Single-Ended ADC

Introduction

Author: Kristian Saxrud Bekken, Microchip Technology Inc.

A common requirement for microcontroller applications is the need to sense the real world in one way or another.

This requires bridging the gap between the digital dimension of a microcontroller and the analog realm of the real

world. In most cases, this is accomplished by using a sensor that translates the magnitude of a physical phenomenon

to an analog voltage which is routed to a pin on the microcontroller. Lastly, a dedicated part of the microcontroller

called an analog-to-digital converter, also referred to as an ADC or A/D converter, transforms the analog voltage to a

digital value to be further processed by the microcontroller.

Most analog sensors either output their measured value as a single analog voltage signal or as a difference between

two analog voltage signals. The two concepts are referred to as single-ended signaling and differential signaling,

respectively.

This white paper provides a high-level introduction to A/D conversion of single-ended and differential analog signals

by presenting the main advantages and drawbacks for the two approaches, as well as a selection of common

applications and useful considerations.

Table of Contents

Introduction.....................................................................................................................................................1

1. Single-Ended Operation..........................................................................................................................3

1.1. General Concept.......................................................................................................................... 3

1.2. Advantages and Drawbacks.........................................................................................................3

1.3. Typical Applications......................................................................................................................3

2. Differential Operation.............................................................................................................................. 5

2.1. General Concept.......................................................................................................................... 5

2.2. Advantages and Drawbacks.........................................................................................................6

2.3. Typical Applications......................................................................................................................6

3. Considerations........................................................................................................................................ 7

4. Revision History...................................................................................................................................... 8

The Microchip Website...................................................................................................................................9

Product Change Notification Service..............................................................................................................9

Customer Support.......................................................................................................................................... 9

Product Identification System.......................................................................................................................10

Microchip Devices Code Protection Feature................................................................................................ 10

Legal Notice................................................................................................................................................. 10

Trademarks.................................................................................................................................................. 10

Quality Management System....................................................................................................................... 11

Worldwide Sales and Service.......................................................................................................................12

Differential and Single-Ended ADC

1. Single-Ended Operation

1.1 General Concept

The simplest and most widely used analog sensors provide single-ended signals. These are designed to be

connected to the same ground level as the microcontroller and to provide their measurement result as an analog

voltage signal on a single wire referenced to this common ground. All basic ADCs support single-ended operation.

An ADC can be designed to operate in different ways, and the amount of time required to perform an analog-to-digital

conversion will vary between ADCs. Regardless, the result is a digital representation of the analog input value. The

digital value will typically be an integer between and 0 2

n-1 n, where is the resolution of the ADC in bits. An integer

value of means that the analog voltage level is the same as ground, while the maximum value (0 2

n-1) corresponds

to the level of what is referred to as the ADC voltage reference (V

ref). The voltage reference defines the conversion

range of the ADC, which for single-ended operation means that an analog input above this level still produces the

maximum digital value, while an input below ground level gives a digital value of . In most cases, the ADC voltage0

reference can be selected among different levels between ground and the microcontroller supply voltage in order to

utilize as much of the ADC resolution as possible for inputs in a given voltage range.

A 12-bit single-ended ADC will most likely have an output range of . If the selected [0,4095] V

ref is 2.0V, and the

analog input signal is 0.5V, the corresponding digital value can be calculated as follows:

Equation 1-1. Example - 12-bit Single-Ended Conversion

ADC Output = Input



Total ADC Counts

=0.5V

2.0V 4096

= 1024

1.2 Advantages and Drawbacks

Whether single-ended operation is the best choice in a given setting depends on the specific application. Below are

some of the main advantages and drawbacks associated with this approach.

Main advantages:

• Both sensors and microcontrollers are available at very low cost

• Occupies only one analog microcontroller input per sensor

• In most cases conceptually simple and easy to use

• Large selection of available sensors and microcontrollers

Main drawbacks:

• Sensitive to noise along the analog signal path

• Sensitive to common-mode noise on the ground and reference voltage levels of the microcontroller

• The signal path between the sensor and the microcontroller should be as short as possible to minimize noise

and ground-level differences

• Conditioning circuitry that adds cost and unwanted dynamic effects might be needed

1.3 Typical Applications

There are numerous types of single-ended analog sensors available. Some of the most common use-cases in

microcontroller applications are:

• Potentiometers for measuring angle or position

• Light intensity measurement

• Infrared and ultrasonic range measurement

Differential and Single-Ended ADC

Single-Ended Operation

Specyfikacje produktu

Marka:	Microchip
Kategoria:	Niesklasyfikowane
Model:	ATmega32U4

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Microchip ATmega32U4, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Microchip

Microchip ATECC608B Instrukcja

7 Października 2024

Microchip HV860 Instrukcja

7 Października 2024

Microchip EVB-LAN9255 Instrukcja

7 Października 2024

Microchip LX4580 Instrukcja

7 Października 2024

Microchip LX7720 Instrukcja

7 Października 2024

Microchip AT32UC3C0128C Instrukcja

4 Października 2024

Microchip AT32UC3A3256 Instrukcja

4 Października 2024

Microchip AT32UC3A364 Instrukcja

4 Października 2024

Microchip AT32UC3B0256 Instrukcja

4 Października 2024

Microchip AT32UC3A0512 Instrukcja

4 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024