Instrukcja obsługi Metra Axxess AX-ADGM04

Metra Niesklasyfikowane Axxess AX-ADGM04

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Metra Axxess AX-ADGM04 (10 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/10

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

AX-ADGM04

I N S TA L L A T I O N I N S T R U C T I O N S

INTRODUCTION

INTERFACE FEATURES

TOOLS REQUIRED

• Crimping tool and connectors, or solder gun, solder,

and heat shrink • Small ﬂat-blade screwdriver

• Tape

• Wire cutter • Zip ties

TABLE OF CONTENTS

Connections to be made

For models

without

an ampliﬁer .......................3

For models

with

an analog ampliﬁer ................4

For models

with

a digital ampliﬁer ...................5

12-pin pre-wired ASWC-1 harness ......................6

DIN jack ................................................................6

Installing & programming the AX-ADGM04

AX-ADBOX1 ...........................................................6

AX-ADBOX2 .......................................................... 7

Adjusting the AX-ADGM04 ....................................8

Extra features .........................................................9

GM Data Interface 2012-2016

APPLICATIONS

See inside front cover

The AX-ADGM04 harness is designed for, and must be used with, the

AX-ADBOX1 or AX-ADBOX2 interface (sold separately). Please refer to the

AX-ADBOX1 or AX-ADBOX2 for the 16-pin connector with stripped leads

• Provides accessory power (12-volt 10-amp)

• Maintains the retained accessory power

(R.A.P.) feature

• Provides NAV outputs (parking brake,

reverse, speed sense)

• Retains chimes

• Retains OnStar / OE Bluetooth

• Adjustable OnStar level

• Retains RSE (rear seat entertainment)

• Retains satellite radio

• Retains the factory AUX-IN jack

• Pre-wired ASWC-1 harness

(ASWC-1 sold separately)

• Can be used in non-ampliﬁed, or analog/

digital ampliﬁed models

• Retains balance and fade†

• Micro-B USB updatable

INTERFACE COMPONENTS

• AX-ADGM04 harness

• 4-pin to 4-pin resistor pad harness

† To retain fade in digital ampliﬁed models, use the AX-ADBOX1

APPLICATIONS

CHEVROLET

Avalanche † * 2012-2013

Express † 2013-2015

Malibu

(with monochrome display) 2013-2015

Malibu Limited

(with monochrome display) 2016

CHEVROLET (CONT)

Silverado 2500 / 3500 † * 2014

Silverado † * 2012-2013

Suburban † ** 2012-2014

Tahoe † ** 2012-2014

Trax 2015-2016

GMC

Savana † 2013-2015

Sierra 2500 / 3500 † * 2014

Sierra † * 2012-2013

Yukon / Yukon XL † ** 2012-2014

These vehicles have a digital amp option. Please reference the “Service Parts Identiﬁcation” sticker located in the glove box for the RPO code Y91. If Y91 is present, then the vehicle is equipped with a digital ampliﬁer

These vehicles have a digital amp option. Please reference the “Service Parts Identiﬁcation” sticker located in the glove box for the RPO code Y91, STZ, or UQS. If Y91, STZ, or UQS is present, then the vehicle is equipped with a

digital ampliﬁer

† Only for models equipped with NAV. If not equipped with NAV, use the AX-ADGM01.

REV. 5/4/2020 INSTAX-ADGM04

From the AX-ADGM04 harness to the aftermarket radio:

• Connect the wire to the ground wire.Black

• Connect the Yellow wire to the battery wire.

• If installing either an ASWC-1 or AX-LCD (both sold separately), connect the (2) wires to Red

accessory power.

• Cut off the resistors from the Green Green/Black Purple Purple/Black, , , and wires below the

heat shrink.

• Connect the wire to the left rear positive speaker output.Green

• Connect the wire to the left rear negative speaker output.Green/Black

• Connect the wire to the right rear positive speaker output.Purple

• Connect the wire to the right rear negative speaker output.Purple/Black

• Ensure the (2) 4-pin Molex connectors are connected together.

Note: The 4-pin to 4-pin resistor pad harness will not be used in this application.

• The Black/Yellow wire is used for OnStar level adjustment for models that do not come

equipped with steering wheel controls. Refer to the OnStar level Adjustment section for

further instructions.

• Connect the and RCA jacks to the audio AUX-IN jacks from the aftermarket radio.Red White

• Disregard the wire with a red connector, it will not be used in this application.Pink

Note: The relay attached to the AX-ADGM04 harness is only for audible turn signal clicks.

No extra steps are required to retain this feature, so leave the relay as-is.

Continue to 12-pin pre-wired ASWC-1 harness

CONNECTIONS TO BE MADE

Attention! This interface will work with models that are either non-ampliﬁed, analog ampliﬁed,

or digital ampliﬁed. Please follow the instructions carefully for your model vehicle. Failure to

do so will result in either no sound, or low sound. If you are unsure if your vehicle is factory

ampliﬁed or not, please contact your local dealership.

For models

without

an ampliﬁer:

From the 16-pin harness with stripped leads to the aftermarket radio (harness included with interface):

• Connect the wire to the accessory wire.Red

Note: If installing either an ASWC-1 or AX-LCD (both sold separately), connect the (2) Red

wires on the AX-ADGM04 harness as well.

• Connect the wire to the power antenna wire.Blue/White

• If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.

• If the aftermarket radio has a mute wire, connect the wire to it. If the mute wire is Brown

not connected, the radio will turn off when OnStar is activated.

• Connect the wire to the right front positive speaker output.Gray

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the wire to the left front positive speaker output.White

• Connect the wire to the left front negative speaker output.White/Black

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the wire to the VSS/speed sense wire.Blue/Pink

• Connect the wire to the reverse wire.Green/Purple

• Connect the wire to the parking brake wireLight Green

• Tape off and disregard the following (4) wires, they will not be used in this application:

Green Green/Black Purple Purple/Black, , ,

Specyfikacje produktu

Marka:	Metra
Kategoria:	Niesklasyfikowane
Model:	Axxess AX-ADGM04

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Metra Axxess AX-ADGM04, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Metra

Metra 71-017C Instrukcja

9 Października 2024

Metra AXSP-HK Instrukcja

9 Października 2024

Metra 109-TO7 Instrukcja

9 Października 2024

Metra 95-8273B Instrukcja

9 Października 2024

Metra 95-7822 Instrukcja

9 Października 2024

Metra 82-8703 Instrukcja

9 Października 2024

Metra 88-00-9004 Instrukcja

9 Października 2024

Metra 82-9101 Instrukcja

9 Października 2024

Metra 95-7021HG Instrukcja

9 Października 2024

Metra 82-5608 Instrukcja

9 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024