Instrukcja obsługi Metra AX-HYKIA2-SWC

Metra Niesklasyfikowane AX-HYKIA2-SWC

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Metra AX-HYKIA2-SWC (8 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

AX-HYKIA2-SWC

I N S TA L L AT I O N I N S T R U C T I O N S

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS REQUIRED

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell

caps, etc.)

TABLE OF CONTENTS

Connections to be made ....................................2-3

Installing the AX-HYKIA2-SWC ..............................3

Programming the AX-HYKIA2-SWC ......................4

Steering wheel control settings ....................... 4-7

- L.E.D. feedback ...................................................4

- Changing radio type ..........................................5

Remapping the steering wheel control buttons

.. 5-6

Dual assignment instructions (long button press)

.. 6-7

Troubleshooting .....................................................7

Hyundai Data Interface with SWC 2012-2016

APPLICATIONS

• Provides NAV outputs (parking brake, reverse, speed sense)

• Retains audio controls on the steering wheel

• Retains BlueLink

• Designed for ampliﬁed* and non-ampliﬁed models

• Retains the factory backup camera

• Retains balance and fade

• Micro “B” USB updatable

HYUNDAI

Veloster (without NAV) 2016

Veloster 2012-2015

• AX-HYKIA2-SWC interface

• AX-HYKIA2-SWC harness

• 16-pin harness with stripped leads

• Female 3.5mm connector with stripped leads

* Requires the AX-HYKIA-SPDIF (sold separately)

CONNECTIONS TO BE MADE

From the 16-pin harness with stripped leads to the aftermarket radio:

• Connect the Red wire to the accessory wire.

• If the vehicle comes equipped with a factory ampliﬁer, connect the Blue/White wire to the

amp turn-on wire.

• If the aftermarket radio has a mute wire, connect the Brown wire to it. If the mute wire is

not connected, the radio will turn off when BlueLink is activated.

• Connect the Gray wire to the right front positive speaker output.

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the White wire to the left front positive speaker output.

• Connect the White/Black wire to the left front negative speaker output.

• Tape off and disregard the following (9) wires, they will not be used in this application:

Blue/Pink Blue/White Green Green/Black Green/Purple Orange/White, *, , , , Light Green, ,

Purple Purple/Black,

* Non-ampliﬁed models

From the AX-HYKIA2-SWC harness to the aftermarket radio:

• Connect the Black wire to the ground wire.

• Connect the Yellow wire to the battery wire.

• Connect the Blue wire to the power antenna wire.

• If the aftermarket radio has an illumination wire, connect the Orange wire to it.

• Connect the Green wire to the left rear positive speaker output.

• Connect the Green/Black wire to the left rear negative speaker output.

• Connect the Purple wire to the right rear positive speaker output.

• Connect the Purple/Black wire to the right rear negative output.

The following (3) wires are only for a multimedia/navigation radio that requires these wires.

• Connect the Blue/Pink wire to the VSS/speed sense wire.

• Connect the Green/Purple wire to the reverse wire.

• Connect the Light Green wire to the parking brake wire.

• Connect the Red and White RCA jacks to the audio AUX-IN jacks of the aftermarket radio.

• If the vehicle is equipped with a factory backup camera, connect the Yellow RCA jack to the

backup camera input.

• The 14-pin harness will only be used for models that come equipped with a factory

ampliﬁer. Connect the AX-HYKIA-SPDIF (sold separately) to this connector.

Continued on the next page

REV. 1/15/2018 INSTAX-HYKIA2-SWC

With the key in the off position:

• Connect the 16-pin harness with stripped leads, and the AX-HYKIA2-SWC harness, into the

interface.

• For models equipped with a factory ampliﬁer, connect the AX-HYKIA-SPDIF (sold

separately) to the HYKIA2-SWC interface.

Attention!

Do not connect the AX-HYKIA1-SWC harness to the wiring harness in the vehicle just yet

Attention!

If retaining steering wheel controls, ensure that the jack/wire is connected to the

radio before proceeding. If this step is skipped, the interface will need to be reset for the steering

wheel controls to function.

CONNECTIONS TO BE MADE INSTALLING THE AX-HYKIA2-SWC

3.5mm jack steering wheel control retention:

• The 3.5mm jack is to be used to retain audio controls on the steering wheel control.

• For

the radios listed below, connect the

female 3.5mm connector with stripped leads

to the male

3.5mm SWC jack from the AX-HYKIA2-SWC harness. Any remaining wires tape off and disregard

• Eclipse: Connect the steering wheel control wire, normally Brown Brown/White, to the

wire of the connector. Then connect the remaining steering wheel control wire, normally

Brown/White Brown, to the wire of the connector.

• Metra OE: Connect the steering wheel control Key 1 wire (Gray) to the wire.Brown

• Kenwood or select JVC with a steering wheel control wire: Connect the Blue/Yellow

wire to the Brown wire.

• XITE: Connect the steering wheel control SWC-2 wire from the radio to the Brown wire.

• Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AX-SWC-PARROT (sold

separately), and then connect the 4-pin connector from the AX-SWC-PARROT into the radio

Note:

The radio must be updated to rev. 2.1.4 or higher software.

• Universal “2 or 3 wire” radio: Connect the steering wheel control wire, referred to

as Key-A or SWC-1, to the Brown wire of the connector. Then connect the remaining

steering wheel control wire, referred to as Key-B or SWC-2, to the Brown/White wire of

the connector. If the radio comes with a third wire for ground, disregard this wire.

Note:

After the interface has been programmed to the vehicle, refer to the manual provided

with the radio for assigning the SWC buttons. Contact the radio manufacturer for more

information

• For all other radios: Connect the 3.5mm jack from the AX-HYKIA2-SWC harness, into the jack

on the aftermarket radio designated for an external steering wheel control interface. Please

refer to the aftermarket radios manual if in doubt as to where the 3.5mm jack goes to.

Specyfikacje produktu

Marka:	Metra
Kategoria:	Niesklasyfikowane
Model:	AX-HYKIA2-SWC

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Metra AX-HYKIA2-SWC, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Metra

Metra 71-017C Instrukcja

9 Października 2024

Metra AXSP-HK Instrukcja

9 Października 2024

Metra 109-TO7 Instrukcja

9 Października 2024

Metra 95-8273B Instrukcja

9 Października 2024

Metra 95-7822 Instrukcja

9 Października 2024

Metra 82-8703 Instrukcja

9 Października 2024

Metra 88-00-9004 Instrukcja

9 Października 2024

Metra 82-9101 Instrukcja

9 Października 2024

Metra 95-7021HG Instrukcja

9 Października 2024

Metra 82-5608 Instrukcja

9 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024