Instrukcja obsługi Metra 95-6549


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Metra 95-6549 (4 stron) w kategorii zestaw samochodowy. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/4
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
Metra. The World’s Best Kits.MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 7/26/18 INST95-6549
I N S TA L L A T I O N I N S T R U C T I O N S
95-6549
KIT FEATURES
ISO DDIN radio provision
Complete center dash panel for a factory look
KIT COMPONENTS
• A) Radio/climate control panel • B) Radio brackets • C) Tray • D) Storage pocket • E) Dummy panel • F) Climate control spacers
• G) (6) #8 x 3/8” Pan-head Phillips screws • H) (4) #8 x 5/8” Pan-head Phillips screws • I) (3) #8 x 1/2” Truss-head Phillips screws
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 3/8’ socket wrench • Cutting tool • Grinding tool
• 1/8” drill bit
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation ....................................................2-3
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: 70-1817
Antenna Adapter: N/R
A B C
F HG I
D E
Jeep Wrangler 1997-2002
1.800.221.0932
|
MetraOnline.com
2
1. Unclip the top cover from the instrument
panel, then remove (2) Phillips screws
exposed.
2. Remove the ashtray, then remove (1)
Phillips screw exposed.
3. Starting from the bottom edge of the
radio/climate control panel, unclip,
unplug, and remove the panel.
4.
Remove (2) 3/8” screws securing the
radio to the dash. Slide the radio out,
then unplug and remove the radio.
Continue to Kit Preparation
(Figure A)
1. Remove (4) Phillips screws securing the
climate control panel to the dash, then
temporarily move it out of the way in
preparation for the next step.
2. Cut the shaded area in the sub-dash
to allow room for the radio assembly.
(Figure A)
Some radios may require more Note:
cutting than shown. Cut as needed to
allow room for the aftermarket radio.
The dash cut goes through the Note:
center of the lower left mounting hole.
(See detail)
From the factory radio/climate control panel:
3. Unclip and remove the a/c vents.
(Figure B)
4. Unclip and remove the cigarette lighter/
switch panel.
5. Remove the (2) panel clips.
Continued on the next page
DASH DISASSEMBLY KIT PREPARATION
(Figure A)
Remove shaded area
Detail
(Figure B)
REV. 7/26/2018 INST95-6549 3
To the 95-6549 radio/climate control panel:
7. Clip in the a/c vents.
8. Clip in the cigarette lighter/switch panel.
9. Attach the (2) panel clips.
10.
Clip in either the
storage pocket
or
dummy
panel
to replace the factory ashtray
.
11. Secure the
tray
to the
radio climate/control
panel
using the (2) #8 x 3/8” Phillips
pan-head screws provided. (Figure C)
12. Grind down the climate control panel
locater pins. (Figure D)
13. 1997-1999: Place the
climate control
spacers
onto the back of the climate
control panel, then secure the climate
control panel back to the vehicle using
the (4) #8 x 5/8” pan-head screws screws
provided. (Figure E)
2000-2002: Secure the climate control
panel to the
6549 panel
using the (4)
#8 x 3/8” Phillips pan-head screws
provided.
Continue to Kit Assembly
KIT PREPARATION (CONT.) KIT ASSEMBLY
1. Secure the
radio brackets
to the radio
using the screws supplied with the
radio. (Figure A)
2.
Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to the
radio. Metra recommends using the proper
mating adapter from Metra and/or Axxess.
Test the radio for proper operation
.
3. Secure the radio assembly to the dash
using (1) factory screw in the top right.
Drill an 1/8” hole in the (3) remaining
screw holes in the brackets, then use the
(3) #8 x 1/2” Phillips truss-head screws
provided to fully secure the radio.
4.
Reassemble the dash in reverse order of
disassembly to complete the installation
.
(Figure A)
(Figure C)
(Figure E)
(Figure D)


Specyfikacje produktu

Marka: Metra
Kategoria: zestaw samochodowy
Model: 95-6549

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Metra 95-6549, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje zestaw samochodowy Metra

Metra

Metra 95-5026 Instrukcja

28 Grudnia 2024
Metra

Metra 95-7883HG Instrukcja

28 Grudnia 2024
Metra

Metra AX-ADCT4 Instrukcja

28 Grudnia 2024
Metra

Metra 99-7345B Instrukcja

28 Grudnia 2024
Metra

Metra 99-7339B Instrukcja

28 Grudnia 2024
Metra

Metra 99-7367HG Instrukcja

8 Października 2024
Metra

Metra 99-8223 Instrukcja

8 Października 2024
Metra

Metra 99-7422 Instrukcja

8 Października 2024
Metra

Metra 99-7875 Instrukcja

8 Października 2024
Metra

Metra 99-3302 Instrukcja

8 Października 2024

Instrukcje zestaw samochodowy

Najnowsze instrukcje dla zestaw samochodowy

Nokia

Nokia HF-33W Instrukcja

15 Stycznia 2025
Scosche

Scosche HA1714B Instrukcja

28 Grudnia 2024
HTC

HTC Car Kit Instrukcja

15 Grudnia 2024
Scosche

Scosche BTFreq Pro Instrukcja

7 Października 2024
Kogan

Kogan KAPCARSTE7A Instrukcja

7 Października 2024
Arkon

Arkon SM517 Instrukcja

6 Października 2024
Pioneer

Pioneer 12.301232-04 Instrukcja

6 Października 2024
Havis

Havis C-HDM-201 Instrukcja

5 Października 2024
Havis

Havis PKG-PSM-215 Instrukcja

5 Października 2024