Instrukcja obsługi Maytag MK2160AS

Maytag Magnetostrykcja MK2160AS

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Maytag MK2160AS (12 stron) w kategorii Magnetostrykcja. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
MICROWAVE OVEN BUILT-IN TRIM KIT
INSTALLATION INSTRUCTIONS
Built-In Trim Kit Models MK2167, MK2160
UL listed for use over any electric or gas built-in oven, up to 30" (76.2 cm) wide
INSTRUCTIONS D’INSTALLATION
GARNITURE ENCASTRÉE POUR FOUR À MICRO-ONDES
Garniture encastrée pour modèles MK2167, MK2160
Homologation UL pour utilisation au-dessus de tous les fours encastrés électriques ou gaz, jusqu’à 30" (76,2 cm) de largeur
MICROWAVE OVEN SAFETY
Table of Contents / Table des matières
MICROWAVE OVEN SAFETY ...................................................1
INSTALLATION INSTRUCTIONS..............................................2
Tools and Parts .......................................................................2
Location Requirements...........................................................2
Required Cutout Dimensions..................................................2
Trim Kit Frame Dimensions.....................................................3
Electrical Requirements ..........................................................3
Prepare Microwave Oven........................................................3
Prepare Cutout/Cabinet Opening ...........................................4
Install the Microwave Oven.....................................................5
Install Trim Kit Frame ..............................................................6
SÉCURITÉ DU FOUR À MICRO-ONDES...........................................7
INSTRUCTIONS D’INSTALLATION....................................................7
Outillage et pièces.............................................................................7
Exigences d'emplacement................................................................7
Dimensions nécessaires de l'ouverture d'encastrement..................8
Dimensions du cadre de la trousse de garniture..............................8
Spécifications électriques .................................................................9
Préparation du four à micro-ondes...................................................9
Préparation de l'ouverture d'encastrement ....................................10
Installation du four à micro-ondes ..................................................11
Installation du cadre de la trousse de garniture .............................12
W10532204A
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
2
INSTALLATION INSTRUCTIONS
Tools and Parts
Tools Needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listed here.
Parts Supplied (not shown to scale
Location Requirements
The microwave oven may be installed over a built-in oven. If
installing over a built-in oven, make sure there is a minimum of 3"
(7.6 cm) between the top of the lower oven cutout and the
microwave oven cutout floor.
The microwave oven may also be installed in a cabinet by itself
(without a built-in oven below). For best usability, we recommend
a minimum distance of 36" (91.4 cm) from the floor to the cutout
floor.
Make sure the surrounding cabinetry has clearance to open and
close freely. Allow a clearance of at least 1⁹⁄₁₆" (4.0 cm) below the
cutout floor (3" [7.6 cm] for installation above a built-in oven), and
a clearance of at least 2" (5.1 cm) above the cutout opening.
Required Cutout Dimensions
NOTES:
■Depth requirements depend upon receptacle and its location
within or outside of recommended region. See illustration and
chart above.
■Height dimension is critical: 17" (43.2 cm) minimum, 17¹⁄₈"
(43.5 cm) maximum.
■Width measurement has ±1/16" (2 mm) tolerance.
■3" (7.6 cm) minimum dimension is from lower oven cutout
ceiling to microwave oven cutout floor.
■Trim kit frame extends 1¹⁄₁₆" (2.7 cm) above and below the
cutout opening.
■Measuring tape
■Pencil
■Phillips screwdriver
■Drill
■7/64" drill bit
Rails (2) Bottom duct Trim kit frame
Short screws (14)
(11 + 3 extra)
Long wood screws (6 - painted)
(4 + 2 extra)
A. Upper cabinet
B. Microwave oven cutout
C. Lower oven cutout
D. Lower cabinets
E. Floor
3"
(7.6 cm)
BB
D
36"
(91.4 cm)
C
2"
(5.1 cm)
2"
(5.1 cm)
1 "⁹⁄₁₆
(4.0 cm)
A
E
A. Trim kit frame overhang
B. Cutout for lower oven
C. Recommended region for receptacle
location (no less than 6" [15.2 cm] to
the right of cutout centerline)
D. Cutout centerline
Receptacle Location Minimum Depth
Within recommended
region
18" (45.7 cm) with flush receptacle;
21" (53.2 cm) with non-flush receptacle
Outside recommended
region
19¹⁄₂" (49.5 cm) with flush receptacle;
22¹⁄₂" (57.2 cm) with non-flush
receptacle
3"
(7.6 cm)
6"
(15.2 cm)
A
1 "¹⁄₁₆
(2.7 cm)
1 "¹⁄₁₆
(2.7 cm)
B
CD
23¹⁄₈" (58.7 cm)17 " (43.5 cm)¹⁄₈
max.
17" (43.2 cm)
min.
For minimum depth requirements, see chart.
3
Trim Kit Frame Dimensions
*27" (68.6 cm) trim kit
**30" (76.2 cm) trim kit
Electrical Requirements
Observe all governing codes and ordinances.
Required:
■A 120 volt, 60 Hz, AC only, 15- or 20-amp electrical supply
with a fuse or circuit breaker.
Recommended:
■A time-delay fuse or time-delay circuit breaker.
■A separate circuit serving only this microwave oven.
Prepare Microwave Oven
1. Unplug microwave oven before proceeding with installation.
2. Remove any loose items inside microwave oven.
3. Gently turn microwave oven onto its top, with the door facing
forward (toward installer).
4. Align the two rails on the microwave oven bottom, as shown,
making sure the flanges are forward and pointing up.
5. Secure the rails to the microwave oven bottom using four
short screws.
26⁷⁄₈" (68.2 cm)**
29³⁄₄" (75.6 cm)**
2 " (5.2 cm)*¹⁄₁₆
*
3¹⁄₂" (8.9 cm)**
22 " (57.8 cm)³⁄₄
12¹⁄₄
"
(31.1 cm
)
1 " (3.0 cm)³⁄₁₆
19 "¹⁄₈
(48.6 cm)
3⁷⁄₁₆"
(8.7 cm)
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
A. Rails (2)
B. Microwave oven bottom
C. Short screws (4)
D. Flanges
E. Door
GROUNDING INSTRUCTIONS
SAVE THESE INSTRUCTIONS
■ For all cord connected appliances:
The microwave oven must be grounded. In the event of
an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric
current. The microwave oven is equipped with a cord
having a grounding wire with a grounding plug. The plug
must be plugged into an outlet that is properly installed
and grounded.
WARNING: Improper use of the grounding plug can
result in a risk of electric shock. Consult a qualified
electrician or serviceman if the grounding instructions are
not completely understood, or if doubt exists as to whether
the microwave oven is properly grounded.
Do not use an extension cord. If the power supply cord is
too short, have a qualified electrician or serviceman install
an outlet near the microwave oven.

Specyfikacje produktu

Marka: Maytag
Kategoria: Magnetostrykcja
Model: MK2160AS

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Maytag MK2160AS, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Magnetostrykcja Maytag

Maytag

Maytag UMCS5022RZ Instrukcja

15 Października 2024
Maytag

Maytag UMV1160CW Instrukcja

25 Września 2024
Maytag

Maytag MMV5208WS Instrukcja

25 Września 2024
Maytag

Maytag MMV1164WS Instrukcja

25 Września 2024
Maytag

Maytag MMV4205DH Instrukcja

25 Września 2024
Maytag

Maytag MMV6190FZ Instrukcja

25 Września 2024
Maytag

Maytag MMMF6030PB Instrukcja

25 Września 2024
Maytag

Maytag MMV1153BAB Instrukcja

25 Września 2024
Maytag

Maytag MMV5208WW Instrukcja

25 Września 2024
Maytag

Maytag MMV5227JK Instrukcja

25 Września 2024

Instrukcje Magnetostrykcja

Najnowsze instrukcje dla Magnetostrykcja

Sharp

Sharp R-334W Instrukcja

15 Października 2024
Whirlpool

Whirlpool WMCS7022RS Instrukcja

15 Października 2024
Insignia

Insignia NS-MW11BK5 Instrukcja

15 Października 2024
Insignia

Insignia NS-MW7RM5 Instrukcja

15 Października 2024
Whirlpool

Whirlpool AMW 730/WH Instrukcja

14 Października 2024
Whirlpool

Whirlpool AVM 220/WP/AV Instrukcja

14 Października 2024
Daewoo

Daewoo KOR-6CDS8 Instrukcja

14 Października 2024
Pelgrim

Pelgrim MAG740 Instrukcja

13 Października 2024
Sharp

Sharp R-2V11B Instrukcja

13 Października 2024
Küppersbusch

Küppersbusch EMWG 8604.0 Instrukcja

13 Października 2024