Instrukcja obsługi Manitowoc UY-0190A

Manitowoc maszyna do produkcji lodów UY-0190A

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Manitowoc UY-0190A (22 stron) w kategorii maszyna do produkcji lodów. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/22

Part Number: 04002909 Rev02 4/16

UnderCounter Ice Machines

Installation, Operation and Maintenance Manual

Safety Notices

Read these precautions to prevent personal injury:

• Read this manual thoroughly before operating,

installing or performing maintenance on the

equipment. Failure to follow instructions in this

manual can cause property damage, injury or death.

• Routine adjustments and maintenance procedures

outlined in this manual are not covered by the

warranty.

• Proper installation, care and maintenance are essential

for maximum performance and trouble-free operation

of your equipment.

Visit our website www.manitowocice.com for manual

updates, translations, or contact information for

service agents in your area.

• This equipment contains high voltage electricity and

refrigerant charge. Installation and repairs are to be

performed by properly trained technicians aware of

the dangers of dealing with high voltage electricity

and refrigerant under pressure. The technician must

also be certified in proper refrigerant handling

and servicing procedures. All lockout and tag out

procedures must be followed when working on this

equipment.

• This equipment is intended for indoor use only. Do

not install or operate this equipment in outdoor areas.

nWarning

Follow these electrical requirements during

installation of this equipment.

• All field wiring must conform to all applicable

codes of the authority having jurisdiction. It is

the responsibility of the end user to provide the

disconnect means to satisfy local codes. Refer to rating

plate for proper voltage.

• This appliance must be grounded.

• This equipment must be positioned so that the plug is

accessible unless other means for disconnection from

the power supply (e.g., circuit breaker or disconnect

switch) is provided.

• Check all wiring connections, including factory

terminals, before operation. Connections can become

loose during shipment and installation.

nWarning

Follow these precautions to prevent personal injury

during installation of this equipment:

• Installation must comply with all applicable

equipment fire and health codes with the authority

having jurisdiction.

• To avoid instability the installation area must be

capable of supporting the combined weight of the

equipment and product. Additionally the equipment

must be level side to side and front to back.

• Remove all removable panels before lifting and

installing and use appropriate safety equipment

during installation and servicing. Two or more people

are required to lift or move this appliance to prevent

tipping and/or injury.

• Do not damage the refrigeration circuit when

installing, maintaining or servicing the unit.

• Connect to a potable water supply only.

• This equipment contains refrigerant charge.

Installation of the line sets must be performed by

a properly trained and EPA certified refrigeration

technician aware of the dangers of dealing with

refrigerant charged equipment.

• Legs or casters must be installed and the legs/casters

must be screwed in completely. When casters are

installed, the mass of this unit will allow it to move

uncontrolled on an inclined surface. These units must

be tethered/secured to comply with all applicable

codes. Swivel casters must be mounted on the front

and rigid casters must be mounted on the rear. Lock

the front casters after installation is complete.

• Some 50 Hz models may contain up to 150 grams

of R290 (propane) refrigerant. R290 (propane)

is flammable in concentrations of air between

approximately 2.1% and 9.5% by volume (LEL lower

explosion limit and UEL upper explosion limit). An

ignition source at a temperature higher than 470°C is

needed for a combustion to occur. Refer to nameplate

to identify the type of refrigerant in your equipment.

Only trained and qualified personnel aware of the

dangers are allowed to work on the equipment.

Specyfikacje produktu

Marka:	Manitowoc
Kategoria:	maszyna do produkcji lodów
Model:	UY-0190A

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Manitowoc UY-0190A, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje maszyna do produkcji lodów Manitowoc

Manitowoc CNF0201 Instrukcja

13 Lipca 2024

Manitowoc RNF1020C Instrukcja

13 Lipca 2024

Manitowoc JC-1395 Instrukcja

13 Lipca 2024

Manitowoc K-00068 Instrukcja

13 Lipca 2024

Manitowoc SPA-160 Instrukcja

13 Lipca 2024

Manitowoc D-320 Instrukcja

13 Lipca 2024

Manitowoc D-400 Instrukcja

13 Lipca 2024

Manitowoc SPA-310 Instrukcja

13 Lipca 2024

Manitowoc RF-0266A Instrukcja

13 Lipca 2024

Manitowoc SFA-191 Instrukcja

13 Lipca 2024

Instrukcje maszyna do produkcji lodów

Najnowsze instrukcje dla maszyna do produkcji lodów

Jocel JMFG001764 Instrukcja

5 Października 2024

KitchenAid KUID508HPS Instrukcja

5 Września 2024

Magimix Glacier 11667 Instrukcja

24 Sierpnia 2024

Magimix Glacier 11669 Instrukcja

24 Sierpnia 2024

Magimix Gelato Chef 2200 Instrukcja

24 Sierpnia 2024

Hamilton Beach 68321Z Instrukcja

23 Sierpnia 2024

Hamilton Beach 68550E Instrukcja

23 Sierpnia 2024

Hamilton Beach 68322 Instrukcja

23 Sierpnia 2024

Hamilton Beach 68320 Instrukcja

23 Sierpnia 2024

Magic Chef MCIM30SST Instrukcja

22 Sierpnia 2024