Instrukcja obsługi Makita MLS100

Makita Maszyna do piłowania MLS100

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Makita MLS100 (16 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/16
1
ENGLISH (Original instructions)
INSTRUCTION MANUAL
DOUBLE INSULATION
Compound Miter Saw
MLS100
015058
IMPORTANT: Read Before Using.
2
ENGLISH (Original instructions)
SPECIFICATIONS
Model MLS100
Blade diameter 255 mm
Blade body thickness 1.6 mm - 2.4 mm
Hole diameter
For all countries other than European countries 25.4 mm
For European countries 30 mm
Max. Cutting capacities (H x W) with blade 255 mm in diameter
Miter angle
Bevel angle 0° 45° (left and right)
0° 75 mm x 130 mm 75 mm x 90 mm
45° (left) 48 mm x 120 mm 48 mm x 90 mm
No load speed (min-1) 4,200
Dimensions (L x W x H) 610 mm x 485 mm x 515 mm
Net weight 14.7 kg
Safety class /II
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
END217-5
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
･ Read instruction manual.
･ DOUBLE INSULATION
･ To avoid injury from flying debris, keep
holding the saw head down, after
making cuts, until the blade has come
to a complete stop.
･ Do not place hand or fingers close to
the blade.
･ For your safety, remove the chips, small
pieces, etc. from the table top before
operation.
･ Always set SUB-FENCE to left position
when performing left bevel cuts. Failure
to do so may cause serious injury to
operator.
･ To loosen the bolt, turn it clockwise.
･ Only for EU countries
Do not dispose of electric equipment
together with household waste material!
In observance of the European
Directive, on Waste Electric and
Electronic Equipment and its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an environmentally compatible
recycling facility.
ENE004-1
Intended use
The tool is intended for accurate straight and miter
cutting in wood. With appropriate saw blades, aluminum
can also be sawed.
ENF002-2
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
ENG905-1
Noise
The typical A-weighted noise level determined according
to EN61029:
Sound pressure level (L
pA) : 92 dB (A)
Sound power level (L
WA) : 105 dB (A)
Uncertainty (K) : 3 dB (A)
Wear ear protection
ENH003-15
For European countries only
EC Declaration of Conformity
Makita declares that the following Machine(s):
Designation of Machine:
Compound Miter Saw
Model No./ Type: MLS100
3
Conforms to the following European Directives:
2006/42/EC
They are manufactured in accordance with the following
standard or standardized documents:
EN61029
The technical file in accordance with 2006/42/EC is
available from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
30.5.2014
000331
Yasushi Fukaya
Director
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
GEA005-3
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
9. If operating a power tool in a damp location is
unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
10. Use of power supply via a RCD with a rated
residual current of 30mA or less is always
recommended.
Personal safety
11. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
12. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
13. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.
14. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
15. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
16.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts.
Loose clothes, jewellery
or long hair can be caught in moving parts.
17.
If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of
dust collection can reduce dust-related hazards.
Power tool use and care
18. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.

Specyfikacje produktu

Marka: Makita
Kategoria: Maszyna do piłowania
Model: MLS100

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Makita MLS100, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Maszyna do piłowania Makita

Makita

Makita 5603 Instrukcja

15 Października 2024
Makita

Makita DJV181Z Instrukcja

12 Października 2024
Makita

Makita DUC353Z Instrukcja

8 Października 2024
Makita

Makita JR001GD202 Instrukcja

4 Października 2024
Makita

Makita BSS610 Instrukcja

2 Października 2024
Makita

Makita EA3502S Instrukcja

2 Października 2024
Makita

Makita DJV140 Instrukcja

2 Października 2024
Makita

Makita HS301DWAE Instrukcja

30 Września 2024
Makita

Makita DSS500RFJ Instrukcja

28 Września 2024
Makita

Makita SP6000J Instrukcja

24 Września 2024

Instrukcje Maszyna do piłowania

Najnowsze instrukcje dla Maszyna do piłowania

MSW

MSW -TAS287 Instrukcja

15 Października 2024
MSW

MSW T-SAW300 Instrukcja

15 Października 2024
Black & Decker

Black & Decker KS650 Instrukcja

14 Października 2024
Black & Decker

Black & Decker GKC3630L20 Instrukcja

14 Października 2024
Ferm

Ferm FKS-165 Instrukcja

14 Października 2024
Royal Catering

Royal Catering RCBS-1650 Instrukcja

14 Października 2024
Royal Catering

Royal Catering RCBS-1650.1ECO Instrukcja

14 Października 2024
Husqvarna

Husqvarna 365H Instrukcja

13 Października 2024
Hitachi

Hitachi C 7MFA(LA) Instrukcja

10 Października 2024
RYOBI

RYOBI R36XCHS10 Instrukcja

9 Października 2024