Instrukcja obsługi Makita HP2010N

Makita maszyna wiertnicza HP2010N

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Makita HP2010N (16 stron) w kategorii maszyna wiertnicza. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/16

I N S T R U C T I O N M A N U A L

WARNING:

For your personal safety, READ and UNDERSTAND before using.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

w w w . m a k i t a t o o l s . c o m

Hammer Drill

20 mm (3/4”)

MODEL HP2010N

DOUBLE

INSULATION

SPECIFICATIONS

• Manufacturer reserves the right to change specifications without notice.

• Specifications may differ from country to country.

GENERAL SAFETY RULES USA002-2

(For All Tools)

WARNING:

Read and understand all instructions. Failure to follow all

instructions listed below, may result in electric shock, fire and/or

serious personal injury.

SAVE THESE INSTRUCTIONS

Work Area

1. Keep your work area clean and well lit.

Cluttered benches and dark areas invite acci-

dents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power

tools create sparks which may ignite the dust

or fumes.

3. Keep bystanders, children, and visitors

away while operating a power tool. Distrac-

tions can cause you to lose control.

Model HP2010N

Speed High Low

Capacities

Concrete 13 mm (1/2”) 20 mm (3/4”)

Steel 6.5 mm (1/4”) 13 mm (1/2”)

Wood 20 mm (3/4”) 40 mm (1-1/2”)

No load speed (RPM) 0 - 2,300/min. 0 - 900/min.

Blows per minute 0 - 46,000 0 - 18,000

Overall length 350 mm (13-3/4”)

Net weight 3.0 kg (6.6 lbs)

Electrical Safety

4. Double insulated tools are equipped with

a polarized plug (one blade is wider than

the other.) This plug will fit in a polarized

outlet only one way. If the plug does not fit

fully in the outlet, reverse the plug. If it

still does not fit, contact a qualified elec-

trician to install a polarized outlet. Do not

change the plug in any way. Double insula-

tion eliminates the need for the three wire

grounded power cord and grounded power

supply system.

5. Avoid body contact with grounded sur-

faces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of

electric shock if your body is grounded.

6. Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

7. Do not abuse the cord. Never use the cord

to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil,

sharp edges or moving parts. Replace

damaged cords immediately. Damaged

cords increase the risk of electric shock.

8. When operating a power tool outside, use

an outdoor extension cord marked “W-A”

or “W”. These cords are rated for outdoor

use and reduce the risk of electric shock.

Personal Safety

9. Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use tool while tired or

under the influence of drugs, alcohol, or

medication. A moment of inattention while

operating power tools may result in serious

personal injury.

10. Dress properly. Do not wear loose cloth-

ing or jewelry. Contain long hair. Keep

your hair, clothing, and gloves away from

moving parts. Loose clothes, jewelry, or long

hair can be caught in moving parts.

11. Avoid accidental starting. Be sure switch

is off before plugging in. Carrying tools with

your finger on the switch or plugging in tools

that have the switch on invites accidents.

12. Remove adjusting keys or wrenches

before turning the tool on. A wrench or a

key that is left attached to a rotating part of

the tool may result in personal injury.

13. Do not overreach. Keep proper footing

and balance at all times. Proper footing and

balance enables better control of the tool in

unexpected situations.

14. Use safety equipment. Always wear eye

protection. Dust mask, non-skid safety

shoes, hard hat, or hearing protection must

be used for appropriate conditions. Ordinary

eye or sun glasses are NOT eye protection.

Tool Use and Care

15. Use clamps or other practical way to

secure and support the workpiece to a

stable platform. Holding the work by hand or

against your body is unstable and may lead

to loss of control.

16. Do not force tool. Use the correct tool for

your application. The correct tool will do the

job better and safer at the rate for which it is

designed.

17. Do not use tool if switch does not turn it

on or off. Any tool that cannot be controlled

with the switch is dangerous and must be

repaired.

18. Disconnect the plug from the power

source before making any adjustments,

changing accessories, or storing the tool.

Such preventive safety measures reduce the

risk of starting the tool accidentally.

19. Store idle tools out of reach of children

and other untrained persons. Tools are

dangerous in the hands of untrained users.

20. Maintain tools with care. Keep cutting

tools sharp and clean. Properly maintained

tools with sharp cutting edges are less likely

to bind and are easier to control.

Specyfikacje produktu

Marka:	Makita
Kategoria:	maszyna wiertnicza
Model:	HP2010N
Kolor produktu:	Zielony
Źródło zasilania:	Prąd przemienny
Waga produktu:	2903 g
Waga wraz z opakowaniem:	5262 g
Regulowana prędkość:	Tak
Wskaźnik nacisku:	46000 bpm
Średnica wiertła w betonie (max):	19 mm
Prędkość znamionowa:	2300 RPM
Walizka:	Tak
Rodzaj zacisku:	Klucz
Średnica wiertła w metalu (max):	12.7 mm
Średnica wiertła w drewnie (max):	25.4 mm
Miękki uchwyt:	Tak
Wiercenie:	Tak
Wiercenie udarowe:	Tak
Liczba biegów:	2
Dodatkowa rękojeść:	Tak
Głębokościomierz dołączony:	Tak
Prędkość znamionowa (min):	0 RPM
Szybkozaciskowy uchwyt wiertarski:	Nie