Instrukcja obsługi Makita GD0811C

Makita szlifierka GD0811C

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Makita GD0811C (52 stron) w kategorii szlifierka. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/52
GB Die Grinder Instruction Manual
F Meuleuse droite Manuel d’instructions
D Geradschleifer Betriebsanleitung
I Smerigliatrice diritta Istruzioni per l’uso
NL
Stempelslijpmachine
Gebruiksaanwijzing
E Rectificador Manual de instrucciones
P Retificadeira Manual de instruções
DK Ligesliber Brugsanvisning
GR Λειαντής Οδηγίες χρήσεως
TR Kalıp taşlama makinasıKullanma kılavuzu
GD0801C
GD0811C
2
1 2
3 4
5 6
7
015004 015009
015005 015006
015007 003495
015008
1
1
2
3
4
5
6
8
9
7
10
3
ENGLISH (Original instructions)
Explanation of general view
1 Lock-off lever
2 Switch lever
3 Speed adjusting dial
4 Side handle
5 Wrench 19
6 Wrench 13
7 Collet nut
8 Tighten
9 Loosen
10 8 mm (5/16") Max.
SPECIFICATIONS
• Due to our continuing program of research and
development, the specifications herein are subject to
change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
ENE050-1
Intended use
The tool is intended for grinding ferrous materials or
deburring castings.
ENF002-2
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
GEA010-1
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future
reference.
GEB034-9
DIE GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding Operation:
1. This power tool is intended to function as a
grinder. Read all safety warnings, instructions,
illustrations and specifications provided with
this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
2. Operations such as sanding, wire brushing,
polishing or cutting-off are not recommended to
be performed with this power tool. Operations for
which the power tool was not designed may create a
hazard and cause personal injury.
3. Do not use accessories which are not
specifically designed and recommended by the
tool manufacturer. Just because the accessory can
be attached to your power tool, it does not assure
safe operation.
4. The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannot be adequately controlled.
6. The arbour size of accessories must properly fit
the collet of the power tool. Accessories that do
not match the mounting hardware of the power tool
will run out of balance, vibrate excessively and may
cause loss of control.
7. Mandrel mounted accessories must be fully
inserted into the collet or chuck. If the mandrel is
insufficiently held and/or the overhang of the wheel
is too long, the mounted accessory may become
loose and be ejected at high velocity.
8. Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks. If power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of
the rotating accessory and run the power tool at
maximum no-load speed for one minute.
Damaged accessories will normally break apart
during this test time.
Model GD0801C GD0811C
Collet size Max. 8 mm Max. 8 mm
Max. wheel point diameter
Max. wheel diameter 25 mm 50 mm
Max. mandrel (shank) length 40 mm 40 mm
Rated speed (n) / No load speed (n 0
) 29,000 min–1 7,000 min–1
Overall length 390 mm 390 mm
Net weight 2.0 kg 2.0 kg
Safety class /II

Specyfikacje produktu

Marka: Makita
Kategoria: szlifierka
Model: GD0811C

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Makita GD0811C, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje szlifierka Makita

Makita

Makita 9562CVR Instrukcja

12 Stycznia 2025
Makita

Makita GA9060R Instrukcja

14 Października 2024
Makita

Makita DGA700Z Instrukcja

12 Października 2024
Makita

Makita BBO180 Instrukcja

2 Października 2024
Makita

Makita 9557NB Instrukcja

2 Października 2024
Makita

Makita 9558HNR Instrukcja

2 Października 2024
Makita

Makita DBO484 Instrukcja

2 Października 2024
Makita

Makita CE002G Instrukcja

2 Października 2024
Makita

Makita GA022GD202 Instrukcja

2 Października 2024
Makita

Makita GA7063RX02 Instrukcja

2 Października 2024

Instrukcje szlifierka

Najnowsze instrukcje dla szlifierka

Parkside

Parkside PEXS 270 A1 Instrukcja

13 Stycznia 2025
Tryton

Tryton TDS125B Instrukcja

11 Stycznia 2025
Bosch

Bosch GWS 18V-8 Professional Instrukcja

5 Stycznia 2025
DeWalt

DeWalt DCG415B Instrukcja

3 Stycznia 2025
Einhell

Einhell TC-AG 18/115 Li Instrukcja

31 Grudnia 2025
DeWalt

DeWalt DWE4115 Instrukcja

30 Grudnia 2025
Black Decker

Black Decker 4292 Instrukcja

30 Grudnia 2025
Hazet

Hazet 9032M-36 Instrukcja

30 Grudnia 2025
Einhell

Einhell WS 230-4 Instrukcja

29 Grudnia 2024
RIKON

RIKON 80-800VS Instrukcja

27 Grudnia 2024