Instrukcja obsługi Makita GD0600

Makita szlifierka GD0600

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Makita GD0600 (44 stron) w kategorii szlifierka. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/44
GB Die Grinder Instruction manual
F Meuleuse droite Manuel d’instructions
D Geradschleifer Betriebsanleitung
I Smerigliatrice diritta Istruzioni per l’uso
NL Stempelslijpmachine Gebruiksaanwijzing
E Amoladora recta Manual de instrucciones
P Rectificadora recta Manual de instruções
DK Ligesliber Brugsanvisning
GR Ευθυλειαντήρας Οδηγίες χρήσης
GD0600
007052
2
1 2007053 007055
3 4015678 007056
5007054
123
4
5
4
10 mm (3/8”) MAX.
6
3
ENGLISH (Original instructions)
Explanation of general view
SPECIFICATIONS
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use ENE050-1
The tool is intended for grinding ferrous materials or
deburring castings.
Power supply ENF002-2
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety
Warnings GEA010-1
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
DIE GRINDER SAFETY
WARNINGS GEB034-9
Safety Warnings Common for Grinding Operation:
1. This power tool is intended to function as a
grinder. Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious
injury.
2. Operations such as sanding, wire brushing,
polishing or cutting-off are not recommended to
be performed with this power tool. Operations for
which the power tool was not designed may create a
hazard and cause personal injury.
3. Do not use accessories which are not specifically
designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
4. The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated
speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannot be adequately controlled.
6. The arbour size of accessories must properly fit
the collet of the power tool. Accessories that do not
match the mounting hardware of the power tool will
run out of balance, vibrate excessively and may cause
loss of control.
7. Mandrel mounted accessories must be fully
inserted into the collet or chuck. If the mandrel is
insufficiently held and/or the overhang of the wheel is
too long, the mounted accessory may become loose
and be ejected at high velocity.
8. Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks. If power tool or accessory is
dropped, inspect for damage or install an
undamaged accessory. After inspecting and
installing an accessory, position yourself and
bystanders away from the plane of the rotating
accessory and run the power tool at maximum no-
load speed for one minute. Damaged accessories
will normally break apart during this test time.
9. Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece
fragments. The eye protection must be capable of
stopping flying debris generated by various
operations. The dust mask or respirator must be
capable of filtrating particles generated by your
1. Switch lever
2. Lock-off lever
3. Lock button
4. Wrench 13
5. Collet nut
6. Side handle
Model GD0600
Max. collet capacity 6 mm or 6.35 mm (1/4”)
Wheel Point Max. wheel diameter 38 mm
Max. mandrel (shank) length 46 mm
Rated speed (n) / No load speed (n 0) 25,000 min-1
Overall length 358 mm
Net weight 1.7 kg
Safety class /II

Specyfikacje produktu

Marka: Makita
Kategoria: szlifierka
Model: GD0600

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Makita GD0600, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje szlifierka Makita

Makita

Makita 9562CVR Instrukcja

12 Stycznia 2025
Makita

Makita GA9060R Instrukcja

14 Października 2024
Makita

Makita DGA700Z Instrukcja

12 Października 2024
Makita

Makita BBO180 Instrukcja

2 Października 2024
Makita

Makita 9557NB Instrukcja

2 Października 2024
Makita

Makita 9558HNR Instrukcja

2 Października 2024
Makita

Makita DBO484 Instrukcja

2 Października 2024
Makita

Makita CE002G Instrukcja

2 Października 2024
Makita

Makita GA022GD202 Instrukcja

2 Października 2024
Makita

Makita GA7063RX02 Instrukcja

2 Października 2024

Instrukcje szlifierka

Najnowsze instrukcje dla szlifierka

Bosch

Bosch GWS 30-180 PB Professional Instrukcja

6 Lutego 2025
Hazet

Hazet 9032N-1 Instrukcja

4 Lutego 2025
Hazet

Hazet 9032N-5 Instrukcja

4 Lutego 2025
Parkside

Parkside PEXS 270 A1 Instrukcja

13 Stycznia 2025
Tryton

Tryton TDS125B Instrukcja

11 Stycznia 2025
Bosch

Bosch GWS 18V-8 Professional Instrukcja

5 Stycznia 2025
DeWalt

DeWalt DCG415B Instrukcja

3 Stycznia 2025
Einhell

Einhell TC-AG 18/115 Li Instrukcja

31 Grudnia 2025
DeWalt

DeWalt DWE4115 Instrukcja

30 Grudnia 2025
Black Decker

Black Decker 4292 Instrukcja

30 Grudnia 2025