Instrukcja obsługi Makita GA9062R

Makita szlifierka GA9062R

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Makita GA9062R (16 stron) w kategorii szlifierka. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/16

INSTRUCTION MANUAL

Angle Grinder

GA7062

GA7062R

GA9062

GA9062R

ENGLISH: Original instructions

DOUBLE INSULATION

Read before use.

2 ENGLISH

SPECIFICATIONS

Model: GA7062 GA7062R GA9062 GA9062R

Wheel diameter 180mm 230mm

Max. wheel thickness 7.2mm 6.5mm

Spindle thread M14 or M16 or 5/8″ (country specic)

Rated speed (n) 8,500min-1 6,600min-1

Overall length 450mm

Net weight 5.4kg 5.5kg 5.6kg 5.7kg

Safety class /II

• Due to our continuing program of research and development, the specications herein are subject to change

without notice.

• Specications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

Symbols

The following show the symbols used for the equipment.

Be sure that you understand their meaning before use.

Read instruction manual.

Wear safety glasses.

DOUBLE INSULATION

Only for EU countries

Do not dispose of electric equipment

together with household waste material! In

observance of the European Directive, on

Waste Electric and Electronic Equipment

and its implementation in accordance with

national law, electric equipment that have

reached the end of their life must be col-

lected separately and returned to an envi-

ronmentally compatible recycling facility.

Intended use

The tool is intended for grinding, sanding and cutting of

metal and stone materials without the use of water.

Power supply

The tool should be connected only to a power supply of the same

voltage as indicated on the nameplate, and can only be operated

on single-phase AC supply. They are double-insulated and can,

therefore, also be used from sockets without earth wire.

For public low-voltage distribution

systems of between 220 V and 250 V

Only for model GA7062 / GA9062

Switching operations of electric apparatus cause voltage

uctuations. The operation of this device under unfavor-

able mains conditions can have adverse effects to the

operation of other equipment. With a mains impedance

equal or less than 0.25 Ohms it can be presumed that

there will be no negative effects. The mains socket used

for this device must be protected with a fuse or protective

circuit breaker having slow tripping characteristics.

Noise

The typical A-weighted noise level determined accord-

ing to EN60745:

Model GA7062

Sound pressure level (L

pA) : 91 dB(A)

Sound power level (L

WA) : 102 dB (A)

Uncertainty (K) : 3 dB(A)

Model GA7062R

Sound pressure level (L

pA) : 91 dB(A)

Sound power level (L

WA) : 102 dB (A)

Uncertainty (K) : 3 dB(A)

Model GA9062

Sound pressure level (L

pA) : 91 dB(A)

Sound power level (L

WA) : 102 dB (A)

Uncertainty (K) : 3dB(A)

Model GA9062R

Sound pressure level (L

pA) : 91 dB(A)

Sound power level (L

WA) : 102 dB (A)

Uncertainty (K) : 3dB(A)

WARNING: Wear ear protection.

Vibration

The vibration total value (tri-axial vector sum) deter-

mined according to EN60745:

Model GA7062

Work mode: surface grinding with normal side grip

Vibration emission (a

h, AG) : 7.5 m/s2

Uncertainty (K) : 1.5 m/s2

Work mode: surface grinding with anti vibration side grip

Vibration emission (a

h, AG) : 7.5 m/s2

Uncertainty (K) : 1.5 m/s2

Work mode: disc sanding with normal side grip

Vibration emission (a

h, DS) : 2.5 m/s2

Uncertainty (K) : 1.5 m/s2

Work mode: disc sanding with anti vibration side grip

Vibration emission (a

h, DS) : 2.5 m/s2

Uncertainty (K) : 1.5 m/s2

Model GA7062R

Work mode: surface grinding with normal side grip

Vibration emission (a

h, AG) : 7.5 m/s2

Uncertainty (K) : 1.5 m/s2

3 ENGLISH

Work mode: surface grinding with anti vibration side grip

Vibration emission (a

h, AG) : 7.5 m/s2

Uncertainty (K) : 1.5 m/s2

Work mode: disc sanding with normal side grip

Vibration emission (a

h, DS) : 2.5 m/s2

Uncertainty (K) : 1.5 m/s2

Work mode: disc sanding with anti vibration side grip

Vibration emission (a

h, DS) : 2.5 m/s2

Uncertainty (K) : 1.5 m/s2

Model GA9062

Work mode: surface grinding with normal side grip

Vibration emission (a

h, AG) : 6.5 m/s2

Uncertainty (K) : 1.5 m/s2

Work mode: surface grinding with anti vibration side grip

Vibration emission (a

h, AG) : 6.0 m/s2

Uncertainty (K) : 1.5 m/s2

Work mode: disc sanding with normal side grip

Vibration emission (a

h, DS) : 2.5 m/s2 or less

Uncertainty (K) : 1.5 m/s2

Work mode: disc sanding with anti vibration side grip

Vibration emission (a

h, DS) : 2.5 m/s2 or less

Uncertainty (K) : 1.5 m/s2

Model GA9062R

Work mode: surface grinding with normal side grip

Vibration emission (a

h, AG) : 6.5 m/s2

Uncertainty (K) : 1.5 m/s2

Work mode: surface grinding with anti vibration side grip

Vibration emission (a

h, AG) : 6.0 m/s2

Uncertainty (K) : 1.5 m/s2

Work mode: disc sanding with normal side grip

Vibration emission (a

h, DS) : 2.5 m/s2 or less

Uncertainty (K) : 1.5 m/s2

Work mode: disc sanding with anti vibration side grip

Vibration emission (a

h, DS) : 2.5 m/s2 or less

Uncertainty (K) : 1.5 m/s2

NOTE: The declared vibration emission value has

been measured in accordance with the standard test

method and may be used for comparing one tool with

another.

NOTE: The declared vibration emission value

may also be used in a preliminary assessment of

exposure.

WARNING: The vibration emission during actual

use of the power tool can differ from the declared

emission value depending on the ways in which the

tool is used.

WARNING: Be sure to identify safety measures

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (taking

account of all parts of the operating cycle such as

the times when the tool is switched off and when it is

running idle in addition to the trigger time).

WARNING: The declared vibration emission

value is used for main applications of the power tool.

However if the power tool is used for other applica-

tions, the vibration emission value may be different.

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A

to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings and

all instructions. Failure to follow the warnings and

instructions may result in electric shock, re and/or

serious injury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical Safety

1. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodied plugs and matching outlets will

reduce risk of electric shock.

2. Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

3. Do not expose power tools to rain or wet con-

ditions. Water entering a power tool will increase

the risk of electric shock.

4. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

5. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

6. If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

7. Use of power supply via an RCD with a rated

residual current of 30 mA or less is always

recommended.

Personal Safety

1. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inuence of drugs, alcohol or med-

ication. A moment of inattention while operating

power tools may result in serious personal injury.

Specyfikacje produktu

Marka:	Makita
Kategoria:	szlifierka
Model:	GA9062R

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Makita GA9062R, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje szlifierka Makita

Makita GA9060R Instrukcja

14 Października 2024

Makita DGA700Z Instrukcja

12 Października 2024

Makita BBO180 Instrukcja

2 Października 2024

Makita 9557NB Instrukcja

2 Października 2024

Makita 9558HNR Instrukcja

2 Października 2024

Makita DBO484 Instrukcja

2 Października 2024

Makita CE002G Instrukcja

2 Października 2024

Makita GA022GD202 Instrukcja

2 Października 2024

Makita GA7063RX02 Instrukcja

2 Października 2024

Makita GA013GD101 Instrukcja

2 Października 2024

Instrukcje szlifierka

Najnowsze instrukcje dla szlifierka

HiKOKI GP2S2 Instrukcja

15 Października 2024

Hitachi G 13SR Instrukcja

14 Października 2024

Einhell NBG 150 Instrukcja

9 Października 2024

Einhell TE-AG 18/100 Li-Solo Instrukcja

9 Października 2024

Einhell TC-AG 100 Instrukcja

9 Października 2024

Einhell MWS 115/2 Instrukcja

9 Października 2024

Einhell Professional TP-AG 2320 Instrukcja

9 Października 2024

Einhell RT-AG 230/180 Instrukcja

9 Października 2024

Einhell WSE 230/5 Instrukcja

9 Października 2024

Einhell TP-AG 1210 Instrukcja

9 Października 2024