Instrukcja obsługi Makita DUC254Z


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Makita DUC254Z (24 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/24
INSTRUCTION MANUAL
Cordless Chain Saw
DUC204
DUC254
DUC254C
ENGLISH: Original instructions
Read before use.
2 ENGLISH
SPECIFICATIONS
Model: DUC204 DUC254 DUC254C
Overall length (without guide bar) 256 mm
Rated voltage D.C. 18 V
Net weight 2.8 - 3.3 kg
Standard guide bar length 200 mm 250 mm
Recommended guide bar
length
with 90PX 200 - 250 mm -
with 91PX 250 mm- -
with 25AP 250 mm-
Applicable saw chain type
(refer to the table below)
90PX 90PX
91PX
25AP
Standard sprocket Number of teeth 6 9
Pitch 3/8″ 1/4″
Chain speed 0 - 24 m/s
(0 - 1,440 m/min)
0 - 22.5 m/s
(0 - 1,350 m/min)
Chain oil tank volume 140 cm
3
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsmaydifferfromcountrytocountry.
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge
BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 / BL1840B / BL1850 / BL1850B / BL1860B
Some of the battery cartridges listed above may not be available depending on your region of residence.
WARNING: Only use the battery cartridges listed above. Use of any other battery cartridges may cause
injuryand/orre.
Saw chain, guide bar, and sprocket combination
Saw chain type 90PX
Number of drive links 33 40
Guide bar Guide bar length 200 mm 250 mm
Cutting length 180 mm 244 mm
Pitch 3/8″
Gauge 1.1 mm
Type Sprocket nose bar
Sprocket Number of teeth 6
Pitch 3/8″
Saw chain type 91PX
Number of drive links 40
Guide bar Guide bar length 250 mm
Cutting length 244 mm
Pitch 3/8″
Gauge 1.3 mm
Type Sprocket nose bar
Sprocket Number of teeth 6
Pitch 3/8″
3 ENGLISH
Saw chain type 25AP
Number of drive links 60
Guide bar Guide bar length 250 mm
Cutting length 250 mm
Pitch 1/4″
Gauge 1.3 mm
Type Carving bar
Sprocket Number of teeth 9
Pitch 1/4″
NOTICE: When using 25AP saw chain, use with Sprocket 9 (optional accessory).
WARNING:Useappropriatecombinationoftheguidebarandsawchain.Otherwisepersonalinjurymay
result.
Symbols
The following show the symbols used for the equipment. Be
sure that you understand their meaning before use.
Read instruction manual.
Wear safety glasses.
Wear ear protection.
Wear a helmet, goggles and ear protection.
Use appropriate protection for foot-leg and
hand-arm.
This saw is to be used by properly trained
operators only.
Do not expose to moisture.
Maximum permissible cut length
Always use two hands when operating the
chain saw.
Direction of chain travel
Sawchainoiladjustment
Ni-MH
Li-ion
Only for EU countries
Do not dispose of electric equipment or battery
pack together with household waste material!
In observance of the European Directives,
on Waste Electric and Electronic Equipment
and Batteries and Accumulators and Waste
Batteries and Accumulators and their implemen-
tation in accordance with national laws, electric
equipment and batteries and battery pack(s)
that have reached the end of their life must be
collected separately and returned to an environ-
mentally compatible recycling facility.
Intended use
The tool is intended for cutting branches and pruning
trees. It is also suitable for tree service.
Noise
The typical A-weighted noise level determined accord-
ing to IEC62841-4-1:
Model DUC204
Sound pressure level (L
pA) : 92.2 dB(A)
Sound power level (L
WA) : 103.2 dB (A)
Uncertainty (K) : 2.5 dB(A)
Model DUC254
Sound pressure level (L
pA) : 92.2 dB(A)
Sound power level (L
WA) : 103.2 dB (A)
Uncertainty (K) : 2.5 dB(A)
Model DUC254C
Sound pressure level (L
pA) : 92.2 dB(A)
Sound power level (L
WA) : 103.2 dB (A)
Uncertainty (K) : 2.5 dB(A)
WARNING: Wear ear protection.
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to IEC62841-4-1:
Model DUC204
Work mode: cutting wood
Vibration emission (a
h,W) : 3.1 m/s2
Uncertainty (K) : 1.5 m/s
2
Model DUC254
Work mode: cutting wood
Vibration emission (a
h,W) : 3.1 m/s2
Uncertainty (K) : 1.5 m/s
2
Model DUC254C
Work mode: cutting wood
Vibration emission (a
h,W) : 4.1 m/s2
Uncertainty (K) : 1.5 m/s
2
NOTE:
The declared vibration emission value has been
measured in accordance with the standard test method and
may be used for comparing one tool with another.
NOTE:
The declared vibration emission value may also be
used in a preliminary assessment of exposure.


Specyfikacje produktu

Marka: Makita
Kategoria: Maszyna do piłowania
Model: DUC254Z

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Makita DUC254Z, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Maszyna do piłowania Makita

Makita

Makita DUC306PG2 Instrukcja

12 Stycznia 2025
Makita

Makita DJR187ZK Instrukcja

12 Grudnia 2024
Makita

Makita 5603 Instrukcja

15 Października 2024
Makita

Makita DJV181Z Instrukcja

12 Października 2024
Makita

Makita DUC353Z Instrukcja

8 Października 2024
Makita

Makita JR001GD202 Instrukcja

4 Października 2024
Makita

Makita BSS610 Instrukcja

2 Października 2024
Makita

Makita EA3502S Instrukcja

2 Października 2024
Makita

Makita DJV140 Instrukcja

2 Października 2024
Makita

Makita HS301DWAE Instrukcja

30 Września 2024

Instrukcje Maszyna do piłowania

Najnowsze instrukcje dla Maszyna do piłowania

Güde

Güde GSS 400 Instrukcja

12 Stycznia 2025
HiKOKI

HiKOKI C 6BU3 Instrukcja

11 Stycznia 2025
DEDRA

DEDRA DED7060 Instrukcja

11 Stycznia 2025
Einhell

Einhell KGS 190 Instrukcja

11 Stycznia 2025
Sun Joe

Sun Joe SWJ599E Instrukcja

11 Stycznia 2025
Maruyama

Maruyama MCV51 Instrukcja

11 Stycznia 2025
Vonroc

Vonroc JS505DC Instrukcja

9 Stycznia 2025