Instrukcja obsługi Makita DPC8132

Makita Maszyna do piłowania DPC8132

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Makita DPC8132 (68 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/68
WARNING!
Read and understand this Manual. Always follow safety precautions in the Instruction and
Safety Manual. Improper use can cause serious injury!
The engine exhaust from this product contains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm. Preserve this Manual carefully!
ATTENTION!
Suivez toujours les conseils de sécurité du présent manuel d’instructions et de sécurité.
Une utilisation incorrecte de la découpeuse peut entraîner des blessures graves!
Conservez avec soin ce manuel! Les gaz d’échappement émis par ce produit contiennent des produits
chimiques connus par l’Etat de Californie pour provoquer le cancer, des défauts de naissance ou autres
dommages de reproduction. Lisez et comprenez ce manuel.
DPC6410, DPC6411
DPC7310, DPC7311
DPC7320, DPC7321
DPC8111, DPC8112
Instruction and Safety Manual
for Gasoline Power Cuts (page 2 - 33)
Manuel d’instructions et de sécurité
de découpeuse thermiques (page 34 - 65)
2
EMISSIONS COMPONENT DEFECT WARRANTY COVERAGE
MAKITA U.S.A, Inc warrant to the initial retail purchaser and each subsequent owner, that this utility equipment was designed, built,
and equipped to conform at the time of initial sale to all applicable regulations of the U.S.
Environmental Protection Agency (EPA), and that the engine is free of defects in materials and workmanship which would cause this
engine to fail to conform with EPA regulations during its warranty period.
For the components listed under PARTS COVERED, the service dealer authorized by MAKITA will, at no cost to you, make the ne-
cessary diagnosis, repair, or replacement necessary to ensure that the engine complies with applicable U.S. EPA regulations.
EMISSION COMPONENT DEFECT WARRANTY PERIOD
The warranty period for this engine begins on the date of sale to the initial purchaser and continues for a period of 2 years.
PARTS COVERED
Listed below are the parts covered by the Emission Components Defect Warranty. Some of the parts listed below may require sche-
duled maintenance and are warranted up to the rst scheduled replacement point for that part.
Fuel Metering System Ignition System
Carburetor and internal parts Spark plugs
Fuel lter, if applicable Flywheel Magneto
Throttle stopper, if applicable Ignition Coil
Choke System, if applicable
Air Induction System Miscellaneous Items Used in Above Systems
Air cleaner plate, Air lter Fuel hoses, clamps and sealing gaskets
Air cleaner case, Intake manifold
OBTAINING WARRANTY SERVICE
To obtain warranty service, take your engine to the nearest MAKITA Factory Service Center or service Center authorized by MAKITA.
Bring your sales receipts indicating date of purchase for this engine. The dealer of service authorized by MAKITA will perform the
necessary repairs or adjustments within a reasonable amount of time and furnish you with a copy of the repair order. All parts and
accessories replaced under this warranty become the property of MAKITA.
WHAT IS NOT COVERED
• Conditions resulting from tampering, misuse, improper adjustment (unless they were made by the service dealer authorized by
MAKITA during a warranty repair), alteration, accident, failure to use the recommended fuel and oil, or not performing required
maintenance services.
• The replacement parts used for required maintenance services.
• Consequential damages such as loss of time, inconvenience, loss of use of the engine or equipment, etc.
• Diagnosis and inspection charges that do not result in warranty-eligible service being performed.
• Any non-authorized replacement part, or malfunction of authorized parts due to use of non-authorized parts.
OWNER’S WARRANTY RESPONSIBILITIES
As the engine owner, you are responsible for the performance of the required maintenance listed in your owner’s manual.
MAKITA recommends that you retain all receipts covering maintenance on your engine, but MAKITA cannot deny warranty solely
for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the engine owner, you should
however be aware that MAKITA may deny warranty coverage if your engine or a part has failed due to abuse, neglect, improper
maintenance or unapproved modications.
You are responsible for presenting your engine to the nearest service dealer authorized by MAKITA when a problem exists.
If you have any questions regarding your warranty rights and responsibilities, you should contact the MAKITA Warranty service
Department at 1-800-4 MAKITA (462-5482) for the information.
THINGS YOU SHOULD KNOW ABOUT THE EMISSION CONTROL SYSTEM WARRANTY:
MAINTENANCE AND REPAIRS
You are responsible for the proper maintenance of the engine. You should keep all receipts and maintenance records covering the
performance of regular maintenance in the event questions arise. These receipts and maintenance records should be transferred
to each subsequent owner of the engine. MAKITA reserves the right to deny warranty coverage if the engine has not been properly
maintained. Warranty claims will not be denied, however, solely because of the lack of required maintenance or failure to keep
maintenance records.
MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY
ANY REPAIR ESTABLISHMENT OR INDIVIDUAL; HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY A SERVICE
DEALER AUTHORIZED BY MAKITA. THE USE OF PARTS THAT ARE NOT EQUIVALENT IN PERFORMANCE AND DURABILITY
TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A BEA-
RING ON THE OUTCOME OF A WARRANTY CLAIM.
If other than the parts authorized by MAKITA are used for maintenance replacements or for the repair of components affecting emis-
sion control, you should assure yourself that such parts are warranted by their manufacturer to be equivalent to the parts authorized
by MAKITA in their performance and durability.
HOW TO MAKE A CLAIM
All repair qualifying under this limited warranty must be performed by a service dealer authorized by MAKITA. In the event that any
emission-related part is found to be defective during the warranty period, you shall notify MAKITA Warranty service Department at
1-800-4 MAKITA (462-5482) and you will be advised of the appropriate warranty service dealer or service providers
where the warranty repair can be performed.
3
Packing
Your MAKITA Power Cut is packed in a cardboard box to pre-
vent shipping damage.
Cardboard is a basic raw material and is consequently reuseable
or suitable for recycling (waste paper recycling).
Table of contents Page
Packing ................................................................................ 3
Delivery inventory .............................................................. 4
Symbols ............................................................................... 4
SAFETY PRECAUTIONS
Intended use ................................................................... 5
General precautions .......................................................5
Protective equipment ...................................................5-6
Fuels / Refuelling ............................................................6
Putting into operation ......................................................6
Cutting discs ...................................................................7
Kickback and lock-in .......................................................8
Working behavior / Method of working ............................ 8
Always observe the following when using
synthetic resin cutting discs .............................................9
Cutting metal ...................................................................9
Cutting masonry and concrete ...................................9-10
Transport and storage ...................................................10
Maintenance .................................................................11
First aid .........................................................................11
Disposal and environmental protection ......................... 11
Technical data ................................................................... 12
Denomination of components ......................................... 13
PUTTING INTO OPERATION
Mounting the cutting disc ...............................................14
Tightening the V-belt / Checking V-belt tension ............15
Installing the pressure water system .......................15-16
Fuels / Refuelling .....................................................16-17
Starting the engine ........................................................18
Cold-starting .................................................................18
Warm-starting ...............................................................19
Stop engine ................................................................... 19
Adjusting the carburetor .................................................. 20
MAINTENANCE
Changing the V-belt ......................................................21
Cleaning the protection hood ........................................22
Cleaning / changing the air lter ..............................22-23
Replacing the spark plug ..............................................24
Replacing the suction head ..........................................24
Replacing the starter cable ...........................................25
Replacing the return spring ...........................................26
Instructions for periodic maintenance ...........................30
Cutting attachment in central / side position ................. 27
Repositioning the cutting attachment .......................27-28
Replacing/cleaning the spark arrester screen ..............28
SPECIAL ACCESSORIES
Diamond cutting discs, trolley, water tank
and pressure water system ............................................29
Service, spare parts and guarantee ...........................30-31
Troubleshooting ............................................................... 31
Extract from spare parts list .......................................32-33
Accessories .................................................................. 33
Service stations (see enclosure)
Thank you for purchasing a MAKITA product!
Congratulations on choosing a MAKITA Power Cut cutoff saw!
We are condent that you will be satised with this modern
piece of equipment. Like our chain saws, the MAKITA Power
Cuts feature specially designed high-performance engines
with outstanding power-to-weight ratios, for heavy-duty yet
lightweight tools.
Other advantages of the MAKITA Power Cuts:
• Sturdy construction and high reliability.
• Maintenance-free electronic ignition, hermetically sealed to
protect against dust and moisture.
• Vibration damping with the MAKITA 2-mass system (D2M) for
tireless working even when guiding the Power Cut by hand.
• Five-stage air-lter system for reliable working even under
very dusty conditions.
• Two options for mounting the cutter attachment: Either cen-
trally, for good balance when guiding the unit manually, or on
the side, for ush cuts along walls or curbsides or horizontally
directly above the ground.
• Extensive range of resin-bonded and diamond grit cutting
discs, trolley with dust catcher, and systems for supplying
water to the disc.
The following industrial property rights apply:
US 08510690, SE 95027298, SE 95027306, IT 95000653,
IT 95000654, GBM 9412558, GBM 9412559.
We want you to be satised with your MAKITA product.
In order to guarantee the optimal function and performance of
your Power Cut and to ensure your personal safety we would
request you to perform the following:
Read this Instruction and Safety Manual carefully before
putting the Power Cut into operation for the rst time,
and strictly observe the safety regulations! Failure to
observe these precautions can lead to severe injury or
death!
WARNING!
Some dust created by power sanding sawing, grind-
ing, drilling, and other construction activities contains
chemicals known (to the State of California) to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and
other masonry products, and
• arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work.
To reduce your exposure to these chemicals: work in
a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specially
designed to lter out microscopic particles.
Only for DPC7310, 7311, 7320, 7321: The Emissions Compliance
Period referred to on the emission Compliance label indicates
the number of operating hours for which the engine has been
shown to meet federal emissions requirements.
Category C= 50 hours, B= 125 hours, and A= 300 hours.

Specyfikacje produktu

Marka: Makita
Kategoria: Maszyna do piłowania
Model: DPC8132

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Makita DPC8132, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Maszyna do piłowania Makita

Makita

Makita DUC306PG2 Instrukcja

12 Stycznia 2025
Makita

Makita DJR187ZK Instrukcja

12 Grudnia 2024
Makita

Makita 5603 Instrukcja

15 Października 2024
Makita

Makita DJV181Z Instrukcja

12 Października 2024
Makita

Makita DUC353Z Instrukcja

8 Października 2024
Makita

Makita JR001GD202 Instrukcja

4 Października 2024
Makita

Makita BSS610 Instrukcja

2 Października 2024
Makita

Makita EA3502S Instrukcja

2 Października 2024
Makita

Makita DJV140 Instrukcja

2 Października 2024
Makita

Makita HS301DWAE Instrukcja

30 Września 2024

Instrukcje Maszyna do piłowania

Najnowsze instrukcje dla Maszyna do piłowania

Husqvarna

Husqvarna 455e Rancher Instrukcja

12 Stycznia 2025
Güde

Güde GSS 400 Instrukcja

12 Stycznia 2025
HiKOKI

HiKOKI C 6BU3 Instrukcja

11 Stycznia 2025
DEDRA

DEDRA DED7060 Instrukcja

11 Stycznia 2025
Einhell

Einhell KGS 190 Instrukcja

11 Stycznia 2025
Sun Joe

Sun Joe SWJ599E Instrukcja

11 Stycznia 2025
Einhell

Einhell BT-MB 550 U Instrukcja

11 Stycznia 2025
Maruyama

Maruyama MCV51 Instrukcja

11 Stycznia 2025
Vonroc

Vonroc JS505DC Instrukcja

9 Stycznia 2025
PowerPlus

PowerPlus POWX53300T Instrukcja

9 Stycznia 2025