Instrukcja obsługi Lucky FF918CS-W

Lucky wykrywacz ryb FF918CS-W

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lucky FF918CS-W (1 stron) w kategorii wykrywacz ryb. Ta instrukcja była pomocna dla 19 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/1

MADE IN CHINA

MANUFACTURER: JINHUA LUCKY ET MANUFACTURER CO.,LTD.

FF918CS-W Wireless

Boat Fish Finder Manual Guide

1. Thank you for choosing LUCKY

FF918CS-W Wireless boat fish finder.

This a ma zing pro duc t is espe cially desi gned f or

amateur and professional fishermen alike, to find out the

loca tion of fish ,d ep th a nd bottom contour of water. The

unit can be used in ocean, river or la ke and is fantastic

for detecting schools of fish in any particular area. Using

amazing and innovative technology, this fish finder is the

ideal tool to bring the fish to you !

-1-

2. Installing Cell Battery of Wireless

Sonar Sensor

1.Please open the wirless sonar sensor cover.

-2-

2. According to picture shows, make the battery with

right direction put into the batte ry hol der, the batte ry

positive level upward, battery into the sheet iron below,

then press down.

Cell Battery

Under Metal Piece

Positive Pole "+"

Upward.

3. Installation is complete

3. Display View

The FF918CS-W displays underwater information

in an easy-to-understand format. The to p of the d isplay

corresponds to the water surface at the transducer, and

the bottom of the display corresponds to the Depth Range

automatically selected for the current water depth. The

Bottom Contour varies as the dep th un de r the boat

changes. Digital readouts provide precise information

for depth, fish and water temperature.

As the boat moves, terrain and bottom composition

variations are displayed.Fish, baitfish and thermoclines

-3-

(underwater temperature changes) are di spla yed when

detected. Underwater conditions vary greatly, so some

experience and interpretation is needed to realize all the

benefits of the FF918CS-W use the picture as a guide to

the most common conditions and practice using the

FF918CS-W over known bottom types.

1-Battery capacity

2-Upper Zoom Range

3-Water Surface Line

4-Small Fish Icon

5 Depth- ruler

6-Medium Fish Icon

7-Lower Zoom Range

-4-

8-Wireless signal indicator

9-Sensitivity

10-Water Depth

11-Water Temperature

12-Large Fish Icon

13-Bottom Contour

5.Powering ON and OFF

Press last 3seconds and release the POWER-MENU

key to power the FF918 -

C WS on. Press and hold the

POWER-MENU key until the unit shuts down to power off.

1-Up arrow key

2-Mode key

3-Power Menu key/

4-Sensitivity key

5-Down arrow key

6-light Key

-5-

START UP

When the FF918CS-W powers on, the will

temporarily display on screen last for 5seconds.Then

will show .

FF918CS-W

From this menu, use the arrow keys to select either

Start-Up, Simulation.

If you do nothing, the unit will default to normal on the

water use.

START UP

SIMULATION

-Use Start-Up for on the water use.

-Use Simulation for learning how to use the system

with simulated sonar data; access Simulator by

pressing the Down Arrow Key once

START UP

6. The Menu System

A simple menu system allows you to access your

FF918CS-W adjustable settings. To activate the menu

system, press the POWER-MENU key.

NOTE: Each time the POWER-MENU key is pressed,the

backlight momentarily illuminates for easy viewing at

night. Adjust the Brightness menu setting to keep the

backlight on.

-6-

Press the POWER-MENU key repeatedly to display the

FF918 CS-W menu settings, one at a time. When a menu

setting is on the display, use the UP and DOWN Arrow

keys to adjust th e menu setting. Menus setting are

removed from the screen automatically after several

seconds.In Normal operating mode,most menu settings

saved to memory will not return to their default values

when the unit is turned off. See individual menu choices

for more information.

SENSITIVITY

1 9

6.2 Sensitivity---

Press the POWER-MENU key until SENSITIVITY appears.

Sensitivity controls how much detail is shown on the

display. Increasing the sensitivity shows more sonar

returns from small baitfish and suspended debris in the

water; however, the display may become too cluttered.

When operating in very clear water or greater depths,

increased sensitivity shows weaker returns that may be

of interest. Decreasing th e sensitivity eliminates the

clutter from the display that is sometimes present in

murky or muddy water. If Sensitivity is adjusted too low,

the display may not show many sonar returns that could

be fish. (1 –9).

Use the User Mode menu choice to change between

these two user modes.

-7-

USER MODE

WIRELESS

6.1 User mode---

USER MODE

WIRELESS

USER MODE

SIMULATION

ZOOM

OFF

Press the POWER - MENU key until DEPTH RANGE

appears. Auto matic is the default s etting. When in

automatic, the lower range will be adjusted by the unit to

follow the bottom. (Auto, 1-45)

NOTE: In manual operation, if the depth is greater than

the depth range settings, the bottom will not be visible on

the display. Select AUTO to return to automatic operation.

6 4 Zoom--- .

Press the POWER - MENU key until ZOOM appears.

Select Auto to magnify the area around the bottom in

order to reveal fish and structure close to the bottom that

may not be visible during normal operation. When ZOOM

is set to Auto, the upper and lower Depth Ranges are

automatically adjusted to keep the area above and below

the bottom on the display. Select Off to re tu rn to normal

operation. (Off, Auto, 1-45).

-8-

DEPTH RANGE

AUTO 4 5

AUTO

6 3 Depth Range---.

FISH ICON

SHALLOW ALARM

OFF

There is also a series of manual ranges which can be

selected. The manual depth ranges are determined by

the present depth conditions.

6 5 Shallow Alarm ---.

Press the POWER-MENU key until Shallow Alarm appears.

Select OFF for no Depth Alarm, or select 1 to 45 meters

to set the alarm depth. An audible alarm sounds when the

depth is equal to or less than the setting. (Off, 1-45)

6 6 Fish Icon ---.

Upper Zoom Range

Structure

Lower Zoom Range

-9-

Make sure press the POWER-MENU key until Fish Icon

appears. Select either Off to view “raw” sonar returns,or

On to view Fish symbols. Fish Icon uses advanced signal

processing to interpret sonar returns, and will display a

Fish Symbol when very selective requirements are met.

A select number of possible fish returns will be displayed

with their associated depth. (On, Off).

FISH ICON

ZOOM

OFF

100

6 7 Fish Alarm---.

Press the POWER-MENU key until FISH ALARM appears.

Select Off for no fish alarm, or one of the following

symbols to set the alarm. An alarm will sound when the

FF918CS-W detects fish that correspond to the alarm

setting. Fish Alarm will only sound if Fish ID+ is also set

to On. (Off, Large, Large/Medium, All).

FISH ALA RM

Large fish only

Large/Medium fish

All fish

FISH ALA RM

-10-

BRIGHTNESS

1 9

BATT ALARM

OFF

13.5

COLOR TONE

RED

UNITS

M / ℃

6 8 Units--- .

Make sure press the POWER-MENU key until UNITS

appears. UNITS selects the units of measure. ( Feet/F,

Meters/C, Feet/C, Meet/F ,where F stands for Fahrenheit

and C stands for Celsius )

6.9 Color Tone---

Make sure press the POWER-MENU key until Color Tone

appears. Selects the method used to represent the bottom

and structure on the display.

(Red, Green, Blue, Orange, Grey)

6 10 Battery Alarm ---.

Make sure press the POWER-MENU key until Battery

Alarm appears. Select Off or 8.6 to 13.5 Volts. Battery

Alarm sounds when the input battery voltage is equal to

or less than the menu setting. ( Off , 8.6 to 13.5 Volts )

6 11 Brightness. ---

-11-

Press the POWER-MENU key until Brightness appears.

Use the backlight for night fishing. Select 1 9 to activate -

the backlight at the desired level.

7. Maintenance

Foll ow these si mp le procedure s to ensure your

FF918CS-W continues to deliver top performance.

7.1.If the unit comes into contact with salt spray, wipe the

affected surfaces with a cloth dampened in fresh water.

7.2.Do not use a chemical glass cleaner on the less - this

may cause cracking in the lens.

7.3.Wh en cle aning the LCD protect ive lens, use a

chamois and non-abrasive, mild cleaner. Do not wipe

while dirt or grease is on the lens. Be careful to avoid

scratching the lens.

7.4.If your boat remains in the water for long period of

time, marine growth can reduce the effectiveness of the

transducer. Periodically clean the face of the transducer

with liquid detergent.

-12-

8. Trouble

Many requests for repair received by LUCKY involve

units that do not actually need repair.

8.1. Nothing happens when I turn the unit on.

Check the power cable connection at both ends. Be

sure the cable is connected correctly to a reliable power

source – red lead to positive, black lead to negative or

ground. Ensure the power available is between 11 and

13 V DC.

-13-

8.2. There is no bottom reading visible on the

display.

In very deep water, it may be necessary to increase the

sensitivity setting manually to maintain a graphic depiction

of the bottom. Inspect the transducer cable from end to

end for breaks, kinks, or cuts in the outer casing of the

cable. If none of these actions identifies an obvious

problem, the transducer itself may be at fault. Be sure to

include the transducer if returning the unit for repair.

8.3.When in very shallow water, I get gaps in the

bottom reading and inconsistent digital depth

indication.

The FF918CS-W will work reliably in water 3 feet

(1 meters) or deeper. Remember that the depth is

measured from the transducer, not from the surface of

the water.

8.5.The display shows many black dots at high

speeds and high sensitivity settings.

You are seeing noise or interference caused by one of

several sources. Noise can be caused by electronic

devices. Turn off any nearby electronics and see if the

problem goes away. Noise can be caused by the engine.

If engine noise is causing the interference, the problem

will intensify at higher RPMs. Increase the engine speed

with the boat stationary to isolate this cause. Propeller

cavitation can also appear as noise on the display. If the

transducer is mounted too close to the propeller, the

turbulence generated can interfere with the sonar signal.

Make sure that the transducer is mounted at least 15”

(380mm) from the propeller.

8.4.The display begins to fade out. Images are

not as sharp as normal.

Check the input voltage. The FF918CS-W w ill not

operate on input voltages below 10 V DC.

-14-

9. Specifications

Depth Capability:---------------------------135 feet (45m)

Power Output:--------------------------------------100 Watts

Sonar Operating Frequency:-------------125 KHz

Sonar Coverage :------------------- 90° in 125KHz;

LCD Matrix: --------------------------MVA-TFT-LCD,65536

Colors,320V x 480H

Power Requirement:---------------------------11 to 13V DC

-15-

Attention Of Using Wireless Sonar:

1. P lease ma ke sure batt eries ar e correctly installed.

After batteries are wholly installed into the battery

holder, they shall be locked tightly with belt. Moreover,

please check if the battery cover has been screwed

tightly, and if the O-shaped ring is placed at the correct

position. If the seal ring breaks away from the slot, it

shall be reinstalled properly, so as to avoid water

leakage. If not properly sealed, or if the seal ring is not

correctly installed, water may flow in, affecting the

normal function of the camera.

2. Please make sure at the batteries are full. If data of the

c amera is found with error in reading, please change

batteries. If there is electricity shortage, the data of

depth may not be accurate or even changes frequently.

In addition, the operating distance will also be reduced

consequently.

3. Please try not to make the wireless sonar sensor fall

off onto hard ground or rocks. This may cause great

impact, making components in it fall off or damaging

the wireless sonar sensor.

4. After being used in sea water, the surface of wireless

sonar sensor and the copper columns shall be washed

with fresh water, so as to avoid copper columns from

being corroded by sea water, and to ensure that the

camera can be operated normally.

5. If water accidentally enters into the wireless sonar

sensor, the batteries shall be removed immediately,

-16-

and water in the holder shall be wiped up as well. After

that, it is required to use dry cloth or paper towel to sop

up water in the battery holder. The wireless sonar

sensor shall not be used only after the water has been

completed removed.

6. It's advised to use fish finder in water more than 1

meters. As fish finder is a high-precision electronic

product to detect fish based on sonar transmission and

reflection, and wavelength of the signal is 1 meters,

but signal cannot be reflected in one wavelength, so it's

impossible to detect fish within 1 meters. Besides the

beam angle of sonar signal is 90 degrees. So the deeper

of the water, the more area is detected, and the more

accurate of the detection is.

7. It's not advised to use the fish finder in environment of

smooth place( like water tank, swimming pool, water

bucket, or fish pond) and hard ground (like ceramic tiles,

cement, glasses or plastics), because the detection

can be inaccurat e. The bot to m of these places is

smooth and hard, adding to their small space, the

signal sent by fish finder will be reflected strongly,

which would increase signal overlapping and interfere

the proper operation of fish finder. So it's better to use

the fish finder in large space like outdoor natural water.

8. It's advised to avoid using fish finder in net cages or

nearby. Signal of fish finder can be interfered by fishing

nets and thick ropes under the water of these places,

adding to high - density fish school, it would cause

distortion of detecting depth and fish school.

-17-

9. After being used in seawater, please wipe the surface

seawater of fish finder with soft cloth.

10. Please clean the screen of fish finder with glasses

cloth to protect the mirror surface, but not with rough

things, which would scratch the mirror surface of fish

finder.

11. Do not put fish finder in high temperature environment

such as below the automobile front windshield, it will

cause damage to inner precise components, and

perfor mance of the fish finder.

12. If there is no signal reception in use,”No signal” will

be displayed on the screen and fish finder will alarm

until reception is regained.

13. It's advised to use fish finder in open space to achieve

an ideal effect. When there are obstacles like buildings,

trees between wireless sonar sensor and fish finder,

signal will be interfered and becomes unstable, and

reception distance is shortened. Please avoid using

two fish finders within the operational distance of one

wireless sonar sensor, as signal of wireless sonar

sensor is strong, and can transmit far. Or else wireless

signal will interfere each other, and cause inaccurate

detection information.

14. It's advised to use in good and stable environment.

Moving or pulling wireless sonar sensor too fast could

cause unstability and intermittent of the signal. Big

waves on the water level would cause strong shake

of wireless sonar sensor, and signal may be lost

temporally.

-18-

15. Do not hang too heavy things on the wireless sonar

sensor, which will make it sink into the water, and

cause signal lost,.

16. Please make sure the lid of wireless sonar sensor is

screwed down to prevent water in to damage the

sensor. So it's advised to use the coin to screw down

the lid.

Specyfikacje produktu

Marka:	Lucky
Kategoria:	wykrywacz ryb
Model:	FF918CS-W

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Lucky FF918CS-W, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje wykrywacz ryb Lucky

Lucky FF918C-T Instrukcja

20 Września 2024

Lucky FL068-W Instrukcja

19 Września 2024

Lucky FF718LIC-WT Instrukcja

15 Września 2024

Lucky FL218TPA-WT Instrukcja

1 Września 2024

Lucky FF918CS-W Instrukcja

6 Lipca 2024

Lucky FF718-W Instrukcja

4 Lipca 2024

Lucky LBT-1-GPS Instrukcja

2 Lipca 2024

Instrukcje wykrywacz ryb

Najnowsze instrukcje dla wykrywacz ryb

Simrad Cruise 5 Instrukcja

8 Października 2024

Closer Pets Fish Mate 5000 GBIO Instrukcja

30 Września 2024

Eagle FishMark 320 Portable Instrukcja

26 Września 2024

Eagle Cuda 300 Portable Instrukcja

26 Września 2024

Garmin Echo 151 Instrukcja

20 Września 2024

Deeper FLDP09 Instrukcja

16 Września 2024

Furuno FCV-30 Instrukcja

16 Września 2024

Garmin Fishfinder 240 Blue Instrukcja

14 Września 2024

Lowrance X-4 Instrukcja

14 Września 2024

Raymarine Dragonfly 7 Instrukcja

10 Września 2024