Instrukcja obsługi Lorex LNB9292

Lorex kamera bezpieczeństwa LNB9292

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lorex LNB9292 (2 stron) w kategorii kamera bezpieczeństwa. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

4K Motorized Varifocal Bullet Camera

with Smart Motion Detection

Important Installation Guidelines

Additional Installation Tips:

• Point the camera where there is the least amount of obstructions (e.g., tree branches).

• Install the camera where vandals cannot easily reach.

• Secure cabling so that it is not exposed or easily cut.

• This camera is rated for outdoor use. Installation in a sheltered location is

recommended.

• Smart motion detection is enabled by default. When enabled, the camera's recording

frame rate is 20 frames per second.

• To obtain the maximum 30 frames per second, smart motion detection must be

disabled.

Optimizing Person and Vehicle Detection Accuracy:

• Angle the camera so that objects of interest appear in the bottom of the camera ⅔

image.

• Choose a location where objects of interest will be no further than 50ft (~15m) from

the camera.

Optimal accuracy for objects

within 50ft (~15m) and in the

bottom of the image.⅔

Lower accuracy for objects

further away than 50ft (~15m)

and/or in the top of the image.⅓

• Angle the camera between 30~60° down from the

level position.

• Install the camera between 8-16ft (2.5-5m) off of

the ground.

Level position (i.e., ceiling)

Optimal

angle

range

NOTE: Accuracy of person and vehicle detection will

be inuenced by multiple factors, such as the object’s

distance from the camera, the size of the object, and

the height and angle of the camera. Night vision will

also impact the accuracy of detection.

LNB9292_QSG_EN_R3

• For a full list of compatible recorders, visit .

lorex.com/compatibility

• Not intended for submersion in water. Installation in a sheltered location

recommended.

• This camera includes an Auto Mechanical IR Cut Filter. When the camera changes

between Day/Night viewing modes, an audible clicking noise may be heard from the

camera. This clicking is normal, and indicates that the camera lter is working.

• For optimal remote viewing from your recorder, an upload speed of 256kbps per

camera is required (default setting). For example, your Internet service package

must support 2Mbps or greater upload speed for 8 cameras, 4Mbps or greater for 16

cameras, and 8Mbps or greater for 32 cameras (your Internet service provider can

conrm your upload speed). You may lower the resolution and bitrate of camera video

streams to further boost performance for slower Internet connections. See your NVR's

user manual at lorex.com for full instructions (see "Conguring Recording Quality"

section).

Disclaimers

Dimensions

9.5” / 242mm

3.6”/91mm

• 4K Motorized Varifocal Bullet Camera with Smart Motion Detection

• Mounting Kit*

• Mounting Template*

• Ethernet Extension Cable with Pre-attached RJ45 Cable Gland*

• Allen Key*

* Per camera in multi-camera packs.

Package Contents

ATTENTION:

It is recommended to connect the camera to the NVR or an external PoE

switch. If using a DC power adapter (not included) with the camera, a

REGULATED power supply is REQUIRED for use with this camera. Use of a

non-regulated, non-conforming power supply can damage this product and

voids the warranty.

• Use the camera only with compatible Lorex NVRs.

• Read this guide carefully and keep it for future reference.

• Follow all instructions for safe use of the product and handle with care.

• Use the camera within given temperature, humidity and voltage levels

noted in the camera’s specications.

• Do not disassemble the camera.

• Do not point the camera directly towards the sun or a source of

intense light.

• Use only a regulated power supply with the product (optional). Use of a

non-regulated, non-conforming power supply can damage the product

and void the warranty.

• Periodic cleaning may be required. Use a damp cloth only. Do not use any

harsh, chemical-based cleaners.

• The supplied cable is rated for surface mounting only. Cables for in-wall

and oor-to-oor installations are sold separately (CMR type). These and

other cables are available at .

lorex.com

Safety Precautions

lorex.com

Ethernet

Extension

Cable

RJ45 Cable Gland

Using the RJ45 Cable Gland (Optional)

The RJ45 cable gland is pre-attached to the

included Ethernet extension cable.

The RJ45 cable gland covers the camera’s Ethernet connector and the RJ45 plug to

provide weather-resistance and protection from dust, dirt and other environmental

contaminants.

To use the RJ45 cable gland:

RJ45 Cable Gland Barrel Camera Ethernet Connector

NOTE: The RJ45 cable gland is weather-resistant. Seal the cap with silicone and/or

electrical tape for additional sealing if it will be exposed to precipitation regularly.

Twist the RJ45 cable gland barrel securely onto the camera Ethernet connector.

Need Help?

Visit us online for up-to-date software

and complete instruction manuals

Click on the tabDownloads

Visit lorex.com

Search for the model

number of your product

Click on your product

in the search results

As our products are subject to continuous improvement, Lorex reserves the right to

modify product design, specications and prices, without notice and without incurring

Nocturnal Series

Lorex N10

LNB9292

Quick Start Guide

Setup Diagram

CameraNVR

Scenario 1: Connect Cameras to NVR

Router

Camera

Router

PoE Switch

ATTENTION:

• This camera is compatible only with select NVRs supporting 4K

camera input. For a list of compatible recorders, visit

lorex.com/compatibility.

• You must connect the camera to a supporting H.265 NVR to take

advantage of H.265 compression. For instructions on enabling H.265

compression, visit lorex.com, and search for “How do I enable H.265

compression?”.

NVR

Scenario 2: Connect Cameras to Local Area Network (LAN)

LNB9292_QSG_EN_R3

Installing the Camera

ATTENTION:

Test your camera prior to selecting a permanent mounting location by temporarily

connecting the camera and cable to your NVR.

Before Installing the Camera

• Decide whether to run the cables through the

wall / ceiling (drilling required) or

along the wall / ceiling.

• If you run the cables along the

wall / ceiling, you must run the

cable through the on cable notch

the base. This will keep the camera

base ush to the surface when mounted.

Cable Notch

To install your camera:

1. Use the included mounting template to mark holes for the screws. Drill

holes for the mounting screws.

NOTE: Insert the included drywall anchors if you are installing the

camera in drywall.

Problem Solution

No picture / signal • Ensure the camera is connected to a compatible NVR

supporting 4K camera input. For full camera compatibility,

visit .

lorex.com/compatibility

• The camera may take up to 1 minute to power up after

being connected to the NVR. Wait two minutes before

following the steps below.

• Ensure the camera is connected to your NVR or to your

local network.

• If you are not using PoE, you must connect the camera to

a 12V DC power adapter (not included).

• If the camera is connected to the LAN, you must search

your network for cameras using the NVR. See the NVR’s

instruction manual.

• Ensure your NVR is properly connected to a TV/monitor.

• There may be an issue with your extension cable run.

Connect the camera to the NVR using a different Ethernet

cable.

Picture is too bright • Ensure your camera isn’t pointed directly at a source of

light (e.g., sun or spotlight).

• Slide the sunshade forward to block excess light.

• Move your camera to a different location.

• Check the brightness and contrast settings on the NVR.

Picture is too dark • If using during the day, the camera may not be getting

enough light. Slide the sunshade backwards to let in

more light.

• Check the brightness and contrast settings on the NVR.

Night vision is not

working

• The night vision activates when light levels drop. The area

may have too much light.

Picture is not clear • Check the camera lens for dirt, dust, spiderwebs. Clean

the lens with a soft, clean cloth.

• Make sure that the cable run is within the limitations

specied in the section ‘Cable Extension Options’.

Bright spot in video

when viewing camera

at night

• Night vision reects when pointing a camera through a

window. Move the camera to a different location.

Picture is in color in

dark conditions

• This camera comes with an image sensor that is extra

sensitive to light, meaning that the camera stays in color

mode at low-light conditions. For instructions on how to

make your camera switch to night mode, visit ,

lorex.com

and search for “How do I make my camera switch to night

mode?”.

No audio • Audio is only supported on Lorex NVRs. For a list of

compatible recorders, visit .

lorex.com/compatibility

• Ensure NVR volume is turned on / turned up.

• Ensure audio function on camera is turned on (see ‘Audio

Settings’).

• Ensure audio is turned up on viewing device.

Low frame rate

(frames per second)

• To obtain the maximum 30 frames per second, you must

connect to a compatible recorder. For a complete list of

compatible recorders, visit .

lorex.com/compatibility

• If your recorder is capable of supporting 30 frames per

second, you will need to disable smart motion detection in

order to use the maximum frame rate.

Troubleshooting

Connect the Ethernet cable to the

camera.

Connect the other end of the

Ethernet cable to the NVR’s PoE

ports. The camera may take a

minute to power up after

being connected.

Connect the other end of the

Ethernet cable to a router or switch

on your network. See your NVR

manual for details on connecting

the camera to your NVR using a

switch or router.

Camera NVR

(Optional)

12V DC Power

Ethernet Cable

NOTE: A 12V DC power adapter

(model#: , not ACCPWR12V1

included) is only required if

connecting the camera’s Ethernet

cable to a router or switch that does

not support PoE.

Mounting

screws (2×)

Camera base

Drywall

anchors

(3×)

Mounting surface

2. Connect cables as shown in

the section “Connecting the

Camera”.

3. Feed the cable through the

mounting surface or cable

notch. Mount the camera

stand to the surface using

the provided screws.

4. Use the included Allen

key to loosen the three

adjustment screws on the

camera base. Make the

necessary camera angle

adjustments.

5. Tighten the adjustment

screws to secure the

position.

6. Remove the vinyl lm from

the camera lens when your

installation is complete.

Adjustment screws

Connecting the Camera Adjusting Zoom and Focus

Adjust the camera’s zoom and focus using a compatible NVR. For more

information, see your NVR’s instruction manual on

lorex.com

Right-click on the

camera’s live view and

then click . AutoFocus

Use the sliders to adjust

zoom and focus.

• Point the camera where there is the least amount of obstructions

(i.e., tree branches).

• Install the camera where vandals cannot easily reach.

• Secure cabling so that it is not exposed or easily cut.

• The camera is rated for outdoor use. Installation in a sheltered location is recommended.

Installation Tips

• You can use a RJ45 coupler or switch (not included) to connect male

ends of Ethernet cable together.

• To extend the cable run beyond 300ft (92m), a switch will be required

(sold separately).

Extend the Ethernet cable run for your camera up to 300ft (92m). See table

below. It is recommended to use UL CMR approved cables available at

lorex.com.

Cable Extension Options

Cable Type Max Cable Run

Distance

Max # of

Extensions

CAT5e (or higher) Ethernet cable 300ft (92m) 3

Specyfikacje produktu

Marka:	Lorex
Kategoria:	kamera bezpieczeństwa
Model:	LNB9292

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Lorex LNB9292, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje kamera bezpieczeństwa Lorex

Lorex LNZ4001 Instrukcja

24 Września 2024

Lorex LNE1001 Instrukcja

24 Września 2024

Lorex LNE45DDB Instrukcja

21 Września 2024

Lorex LNB45ABW Instrukcja

21 Września 2024

Lorex LNE45DDW Instrukcja

21 Września 2024

Lorex LNB45ABB Instrukcja

21 Września 2024

Lorex W261AQ Instrukcja

21 Września 2024

Lorex E842CA Instrukcja

4 Lipca 2024

Lorex E842CAWP Instrukcja

4 Lipca 2024

Lorex E842CAB Instrukcja

4 Lipca 2024

Instrukcje kamera bezpieczeństwa

Najnowsze instrukcje dla kamera bezpieczeństwa

TRENDnet TV-IP602WN Instrukcja

5 Października 2024

Home Protector 72268 Instrukcja

5 Października 2024

TRENDnet TV-IP302PI Instrukcja

5 Października 2024

Abus IPCB42510B Instrukcja

28 Września 2024

Vivotek FE8171V Supreme Instrukcja

28 Września 2024

Vivotek MD7530 Dome Instrukcja

28 Września 2024

Vivotek IP8362 Supreme Instrukcja

28 Września 2024

Vivotek NR8401 NVR Instrukcja

28 Września 2024

Vivotek ST2403 Software Instrukcja

28 Września 2024

Vivotek PZ8111W PTZ Instrukcja

28 Września 2024