Instrukcja obsługi Lorex LNB9232S

Lorex kamera bezpieczeństwa LNB9232S

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lorex LNB9232S (2 stron) w kategorii kamera bezpieczeństwa. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

4K Ultra HD IR Bullet IP Camera

LNB9232_QSG_EN_R1

Quick Start Guide

English Version 1.0

As our products are subject to continuous improvement, Lorex reserves the right

to modify product design, speciﬁcations and prices, without notice and without

• For a full list of compatible recorders, visit lorex.com/compatibility.

• Not intended for submersion in water. Installation in a sheltered location

recommended.

• This camera includes an Auto Mechanical IR Cut Filter. When the camera changes

between Day/Night viewing modes, an audible clicking noise may be heard from

the camera. This clicking is normal, and indicates that the camera ﬁlter is working.

• For optimal remote viewing from your recorder, an upload speed of 256kbps per

camera is required (default setting). For example, your Internet service package

must support 2Mbps or greater upload speed for 8 cameras, 4Mbps or greater

for 16 cameras, and 8Mbps or greater for 32 cameras (your Internet service

provider can conﬁrm your upload speed). You may lower the resolution and

bitrate of camera video streams to further boost performance for slower Internet

connections. See your NVR's user manual at for full instructions (see

lorex.com

"Conﬁguring Recording Quality" section).

Disclaimers

Dimensions

7.6” / 193mm3.1” /78mm

LNB9232 SERIES

• 4K Ultra HD IR Bullet IP Camera

• Mounting Kit*

• Mounting Template*

• Ethernet Extension Cable with Pre-attached RJ45 Cable Gland*

* Per camera in multi-camera packs.

Package Contents

ATTENTION:

It is recommended to connect the camera to the NVR or an external PoE

switch. If using a DC power adapter (not included) with the camera, a

REGULATED power supply is REQUIRED for use with this camera. Use of

a non-regulated, non-conforming power supply can damage this product

and voids the warranty.

• Use the camera only with compatible Lorex NVRs.

• Read this guide carefully and keep it for future reference.

• Follow all instructions for safe use of the product and handle with care.

• Use the camera within given temperature, humidity and voltage levels

noted in the camera’s speciﬁcations.

• Do not disassemble the camera.

• Do not point the camera directly towards the sun or a source of

intense light.

• Use only a regulated power supply with the product (optional). Use of a

non-regulated, non-conforming power supply can damage the product

and void the warranty.

• Periodic cleaning may be required. Use a damp cloth only. Do not use

any harsh, chemical-based cleaners.

• The supplied cable is rated for surface mounting only. Cables for in-wall

and ﬂoor-to-ﬂoor installations are sold separately (CMR type). These

and other cables are available at lorex.com.

Safety Precautions

www.lorex.com

• You can use a RJ45 coupler or switch (not included) to connect male

ends of Ethernet cable together.

• To extend the cable run beyond 300ft (92m), a switch will be required

(sold separately).

Extend the Ethernet cable run for your camera up to 300ft (92m).

See table below. It is recommended to use UL CMR approved cables

available at lorex.com.

Cable Extension Options

Cable Type Max Cable Run

Distance

Max # of

Extensions

CAT5e (or higher) Ethernet cable 300ft (92m) 3

• Point the camera where there is the least amount of obstructions (i.e., tree

branches).

• Install the camera where vandals cannot easily reach.

• Secure cabling so that it is not exposed or easily cut.

• This camera is rated for outdoor use. Installation in a sheltered location is

recommended.

Installation Tips

Ethernet

Extension

Cable

RJ45 Cable Gland

Using the RJ45 Cable Gland (Optional)

The RJ45 cable gland is pre-attached to the

included Ethernet extension cable.

The RJ45 cable gland covers the camera’s Ethernet connector and the RJ45 plug to

provide weather-resistance and protection from dust, dirt and other environmental

contaminants.

To use the RJ45 cable gland:

RJ45 Cable

Gland Barrel

Camera Ethernet

Connector

NOTE: The RJ45 cable gland is weather-resistant. Seal the cap with silicone and/or

electrical tape for additional sealing if it will be exposed to precipitation regularly.

Twist the RJ45 cable gland barrel securely onto the camera Ethernet connector.

Resources

Need Help?

Visit us online for

up-to-date software and

complete instruction manuals

Click on the Downloads tab

Visit lorex.com

Search for the model number

of your product

Click on your product in the

search results

Setup Diagram

CameraNVR

Scenario 1: Connect Cameras to NVR

Router

CameraRouter

PoE Switch

ATTENTION:

• This camera is compatible only with select NVRs supporting 4K

camera input. For a list of compatible recorders, visit

lorex.com/compatibility.

• You must connect the camera to a supporting H.265 NVR to take

advantage of H.265 compression. For instructions on enabling

H.265 compression, visit lorex.com, and search for “How do I

enable H.265 compression?”.

NVR

Scenario 2: Connect Cameras to Local Area Network (LAN)

LNB9232_QSG_EN_R1

Installing the Camera

ATTENTION:

Test your camera prior to selecting a permanent mounting location by

temporarily connecting the camera and cable to your NVR.

Before Installing the Camera

• Decide whether to run the cables through

the wall / ceiling (drilling required) or

along the wall / ceiling.

• If you run the cables along the

wall / ceiling, you must run the

cable through the on cable notch

the base. This will keep the camera

base ﬂush to the surface when mounted.Cable Notch

To install your camera:

1. Use the included mounting template to mark holes for the screws.

Drill holes for the mounting screws.

NOTE: Insert the included drywall anchors if you are installing the

camera in drywall.

4. Use a Philips screwdriver

(not included) to loosen the

adjustment screw.

5. Adjust the camera

position as needed.

6. Tighten the adjustment screw

to secure the position.

Problem Solution

No picture /

signal

• Ensure the camera is connected to a compatible

NVR supporting 4K camera input. For full camera

compatibility, visit lorex.com/compatibility.

• The camera may take up to 1 minute to power

up after being connected to the NVR. Wait two

minutes before following the steps below.

• Ensure the camera is connected to your NVR or

to your local network.

• If you are not using PoE, you must connect

the camera to a 12V DC power adapter (not

included).

• If the camera is connected to the LAN, you must

search your network for cameras using the NVR.

See the NVR’s instruction manual.

• Ensure your NVR is properly connected to a TV/

monitor.

• There may be an issue with your extension cable

run. Connect the camera to the NVR using a

different Ethernet cable.

Picture is too

bright

• Ensure your camera isn’t pointed directly at a

source of light (e.g., sun or spot light).

• Slide the sunshade forward to block excess light.

• Move your camera to a different location.

• Check the brightness and contrast settings on

the NVR.

Picture is too

dark

• If using during the day, the camera may not

be getting enough light. Slide the sunshade

backwards to let in more light.

• Check the brightness and contrast settings on

the NVR.

Night vision is

not working

• The night vision activates when light levels drop.

The area may have too much light.

Picture is not

clear

• Check the camera lens for dirt, dust, spiderwebs.

Clean the lens with a soft, clean cloth.

• Make sure that the cable run is within the

limitations speciﬁed in the section ‘Cable

Extension Options’.

Bright spot

in video when

viewing camera

at night

• Night vision reﬂects when pointing a camera

through a window. Move the camera to a

different location.

Picture is in

color in dark

conditions

• This camera comes with an image sensor that is

extra sensitive to light, meaning that the camera

stays in color mode at low-light conditions.

For instructions on how to make your camera

switch to night mode, visit lorex.com, and search

for “How do I make my camera switch to night

mode?”.

No audio • Audio is only supported on Lorex NVRs. For a list

of compatible recorders, visit

lorex.com/compatibility.

• Ensure NVR volume is turned up.

• Ensure audio function on camera is turned on

(see ‘Audio Settings’).

• Ensure audio is turned up on the viewing device.

Troubleshooting

Connect the Ethernet cable to

the camera.

Connect the other end of the

Ethernet cable to the NVR’s PoE

ports. The camera may take a

minute to power up after

being connected.

Connect the other end of the

Ethernet cable to a router or

switch on your network. See

your NVR manual for details on

connecting the camera to your

NVR using a switch or router.

Camera NVR

(Optional)

12V DC Power

Ethernet Cable

NOTE: A 12V DC power adapter

(model#: ACCPWR12V1, not

included) is only required if

connecting the camera’s Ethernet

cable to a router or switch that

does not support PoE.

Mounting screws (4×)

Camera base

Drywall anchors (4×)

Mounting surface

3. Feed the cable through

the mounting surface or

cable notch and mount

the camera stand to the

surface using the provided

screws.

Adjustment screw

2. Connect cables as shown in the section “Connecting the Camera”.

Connecting the Camera

To enable / disable audio recording and

listen-in audio through a Lorex NVR:

1. From Live View, right-click and click Main

Menu. Enter the system user name (default:

admin) and password.

2. Click ( ) and select > Recording

Recording.

3. Under , select the channel where Channel

the audio-capable camera is connected.

4. Under : Audio/Video

A. Check the box on the left to enable audio

recording and listen-in audio.

NOTE: Listen-in audio requires a monitor with

speakers or speakers connected to the NVR.

B. (Optional) Check the middle checkbox

to enable audio streaming to mobile

applications.

5. Under , select the format Audio Encode

that will be used to record audio. is G711A

recommended.

6. Click to save changes.OK

NOTE: These instructions are based on current NVR interface and Lorex Secure app. For

the most up-to-date instructions, see your NVR’s instruction manual on lorex.com.

Audio Settings

ATTENTION:

Audio recording and listen-in audio are disabled by default. Audio recording and

/ or use of listen-in audio without consent is illegal in certain jurisdictions. Lorex

Corporation assumes no liability for use of its products that does not conform

with local laws.

To enable audio through the Lorex

Secure app:

1. Launch the Lorex Secure app.

From the Home screen, tap the

audio-capable camera to open

the channel in full screen.

2. Tap to access settings for

the camera.

3. Tap the switch next to

Camera Microphone to enable

audio.

Prerequisites:

• You must enable audio on the

camera’s sub stream through

a connected NVR. Follow the

instructions to the left for more

information.

• You must connect your NVR to

the Lorex Secure app. See your

NVR's documentation for details.

Specyfikacje produktu

Marka:	Lorex
Kategoria:	kamera bezpieczeństwa
Model:	LNB9232S

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Lorex LNB9232S, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje kamera bezpieczeństwa Lorex

Lorex LNZ4001 Instrukcja

24 Września 2024

Lorex LNE1001 Instrukcja

24 Września 2024

Lorex LNE45DDB Instrukcja

21 Września 2024

Lorex LNB45ABW Instrukcja

21 Września 2024

Lorex LNE45DDW Instrukcja

21 Września 2024

Lorex LNB45ABB Instrukcja

21 Września 2024

Lorex W261AQ Instrukcja

21 Września 2024

Lorex E842CA Instrukcja

4 Lipca 2024

Lorex E842CAWP Instrukcja

4 Lipca 2024

Lorex E842CAB Instrukcja

4 Lipca 2024

Instrukcje kamera bezpieczeństwa

Najnowsze instrukcje dla kamera bezpieczeństwa

TRENDnet TV-IP602WN Instrukcja

5 Października 2024

Home Protector 72268 Instrukcja

5 Października 2024

TRENDnet TV-IP302PI Instrukcja

5 Października 2024

Abus IPCB42510B Instrukcja

28 Września 2024

Vivotek FE8171V Supreme Instrukcja

28 Września 2024

Vivotek MD7530 Dome Instrukcja

28 Września 2024

Vivotek IP8362 Supreme Instrukcja

28 Września 2024

Vivotek NR8401 NVR Instrukcja

28 Września 2024

Vivotek ST2403 Software Instrukcja

28 Września 2024

Vivotek PZ8111W PTZ Instrukcja

28 Września 2024