Instrukcja obsługi Lincoln Electric Magnum 250 LX

Lincoln Electric Niesklasyfikowane Magnum 250 LX

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lincoln Electric Magnum 250 LX (20 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/20
Operator’s Manual
MAGNUM 250 LX SPOOL GUN
Register your machine:
www.lincolnelectric.com/register
Authorized Service and Distributor Locator:
www.lincolnelectric.com/locator
IM887 | Issue D ate Apr- 14
© Lincoln Global, Inc. All Rights Reserved.
K Number:
K2490-1
Save for future reference
Date Purchased
Code: (ex: 10859)
Serial: (ex: U1060512345)
THANK YOU FOR SELECTING
A QUALITY PRODUCT BY
LINCOLN ELEC TRIC.
Please examine Carton and equiPment For
damage immediately
When this equipment is shipped, title passes to the purchaser upon
receipt by the carrier. Consequently, Claims for material damaged in
shipment must be made by the purchaser against the transportation
company at the time the shipment is received.
saFety dePends on you
Lincoln arc welding and cutting equipment is designed and built with
safety in mind. However, your overall safety can be increased by
proper installation ... and thoughtful operation on your part.
DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT
WITHOUT READING THIS MANUAL AND THE SAFETY PRECAUTIONS
CONTAINED THROUGHOUT. And, most importantly, think before you
act and be careful.
This statement appears where the information must be followed
exactly to avoid serious personal injury or loss of life.
This statement appears where the information must be followed to
avoid minor personal injury or damage to this equipment.
KeeP your head out oF the Fumes.
DON’T get too close to the arc. Use
corrective lenses if necessary to
stay a reasonable distance away
from the arc.
READ and obey the Material Safety
Data Sheet (MSDS) and the warning
label that appears on all containers
of welding materials.
USE ENOUGH VENTILATION or
exhaust at the arc, or both, to keep
the fumes and gases from your breathing zone and the general area.
IN A LARGE ROOM OR OUTDOORS, natural ventilation may be
adequate if you keep your head out of the fumes (See below).
USE NATURAL DRAFTS or fans to keep the fumes away from your
face.
If you de velop unusual symptoms, see your supervisor. Perhaps the
welding atmosphere and ventilation system should be checked.
wear CorreCt eye, ear & body ProteCtion
PROTECT your eyes and face with welding helmet
properly fitted and with proper grade of filter plate
(See ANSI Z49.1).
PROTECT your body from welding spatter and arc
flash with protective clothing including woolen
clothing, flame-proof apron and gloves, leather
leggings, and high boots.
PROTECT others from splatter, flash, and glare with
protective screens or barriers.
IN SOME AREAS, protection from noise may be
appropriate.
BE SURE protective equipment is in good condition.
Also, wear safety glasses in work area AT
AT
AT
AT AT A
A
A
AAL
L
L
LLL
L
L
LL
T
T
T
TTI
I
I
IIM
M
M
MMES.
ES.
ES.
ES.ES.
S
S
S
SSP
P
P
PPEC
EC
EC
ECECI
I
I
IIA
A
A
AAL
L
L
LL
SI
SI
SI
SISITU
TU
TU
TUTUAT
AT
AT
ATATI
I
I
IION
ON
ON
ONONS
S
S
SS
DO NOT WELD OR CUT containers or materials which previously had
been in contact with hazardous substances unless they are properly
cleaned. This is extremely dangerous.
DO NOT WELD OR CUT painted or plated parts unless special
precautions with ventilation have been taken. They can release highly
toxic fumes or gases.
A
A
A
AAd
d
d
ddd
d
d
ddi
i
i
iit
t
t
tti
i
i
iion
on
on
onona
a
a
aal
l
l
ll
p
p
p
ppr
r
r
rre
e
e
eec
c
c
ccau
au
au
auaut
t
t
tti
i
i
iio
o
o
oon
n
n
nna
a
a
aar
r
r
rry
y
y
yy
m
m
m
mmea
ea
ea
eaeas
s
s
ssu
u
u
uur
r
r
rres
es
es
eses
PROTECT compressed gas cylinders from excessive heat, mechanical
shocks, and arcs; fasten cylinders so they cannot fall.
BE SURE cylinders are never grounded or part of an electrical circuit.
REMOVE all potential fire hazards from welding area.
ALWAYS HAVE FIRE FIGHTING EQUIPMENT READY FOR IMMEDIATE
USE AND KNOW HOW TO USE IT.
WARNING
CAUTION
SECTION A:
WARNINGS
CALIFORNIA PROPOSITION 65 WARNINGS
Di
Di
Di
DiDies
es
es
esese
e
e
eel
l
l
ll En
En
En
En Eng
g
g
ggi
i
i
iine
ne
ne
nenes
s
s
ss
Diesel engine exhaust and some of its constituents are known
to the State of California to cause cancer, birth defects, and other
reproductive harm.
G
G
G
GGas
as
as
asaso
o
o
ool
l
l
lli
i
i
iin
n
n
nne
e
e
ee
E
E
E
EEn
n
n
nng
g
g
ggi
i
i
iin
n
n
nne
e
e
ees
s
s
ss
The engine exhaust from this product contains chemicals known
to the State of California to cause cancer, birth defects, or other repro-
ductive harm.
arC welding Can be hazardous. ProteCt
yourselF and others From Possible serious
inJury or death. KeeP Children away. PaCe-
maKer wearers should Consult with their
doCtor beFore oPerating.
Read and understand the following safety highlights. For additional
safety information, it is strongly recommended that you purchase a
copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the
American Welding Society, P.O. Box 351040, Miami, Florida 33135 or
CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety”
booklet E205 is available from the Lincoln Electric Company, 22801
St. Clair Avenue, Cleveland, Ohio 44117-1199.
BE SURE THAT ALL INSTALLATION, OPERATION,
MAINTENANCE AND REPAIR PROCEDURES ARE
PERFORMED ONLY BY QUALIFIED INDIVIDUALS.
FOR ENGINE POWERED
EQUIPMENT.
1.a. Turn the engine off before troubleshooting
and maintenance work unless the
maintenance work requires it to be running.
1.b. Operate engines in open, well-ventilated
areas or vent the engine exhaust fumes outdoors.
1.c. Do not add the fuel near an open flame
welding arc or when the engine is running.
Stop the engine and allow it to cool before
refueling to prevent spilled fuel from
vaporizing on contact with hot engine parts
and igniting. Do not spill fuel when filling tank.
If fuel is spilled, wipe it up and do not start engine until fumes
have been eliminated.
1.d. Keep all equipment safety guards, covers and
devices in position and in good repair.Keep
hands, hair, clothing and tools away from
V-belts, gears, fans and all other moving parts
when starting, operating or repairing
equipment.
1.e. In some cases it may be necessary to remove safety guards to
perform required maintenance. Remove guards only when
necessary and replace them when the maintenance requiring
their removal is complete. Always use the greatest care when
working near moving parts.
1.f. Do not put your hands near the engine fan. Do not attempt to
override the governor or idler by pushing on the throttle control
rods while the engine is running.
1.g. To prevent accidentally starting gasoline engines while turning
the engine or welding generator during maintenance work,
disconnect the spark plug wires, distributor cap or magneto wire
as appropriate.
1.h. To avoid scalding, do not remove the radiator
pressure cap when the engine is hot.
ELECTRIC AND
MAGNETIC FIELDS MAY
BE DANGEROUS
2.a. Electric current flowing through any conductor
causes localized Electric and Magnetic Fields (EMF). Welding
current creates EMF fields around welding cables and welding
machines
2.b. EMF fields may interfere with some pacemakers, and welders
having a pacemaker should consult their physician before
welding.
2.c. Exposure to EMF fields in welding may have other health effects
which are now not known.
2.d. All welders should use the following procedures in order to
minimize exposure to EMF fields from the welding circuit:
2.d.1. Route the electrode and work cables together - Secure
them with tape when possible.
2.d.2. Never coil the electrode lead around your body.
2.d.3. Do not place your body between the electrode and work
cables. If the electrode cable is on your right side, the
work cable should also be on your right side.
2.d.4. Connect the work cable to the workpiece as close as
possible to the area being welded.
2.d.5. Do not work next to welding power source.
iii
SAFETY

Specyfikacje produktu

Marka: Lincoln Electric
Kategoria: Niesklasyfikowane
Model: Magnum 250 LX

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Lincoln Electric Magnum 250 LX, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Lincoln Electric

Lincoln Electric

Lincoln Electric X-Tractor 3A Instrukcja

8 Października 2024
Lincoln Electric

Lincoln Electric X-Tractor 5A Instrukcja

6 Października 2024
Lincoln Electric

Lincoln Electric Circulator Instrukcja

4 Października 2024
Lincoln Electric

Lincoln Electric Handy MIG Instrukcja

4 Października 2024
Lincoln Electric

Lincoln Electric K5334-1 Instrukcja

30 Września 2024
Lincoln Electric

Lincoln Electric Power Arc 5000 Instrukcja

30 Września 2024
Lincoln Electric

Lincoln Electric Country 300 Instrukcja

22 Września 2024
Lincoln Electric

Lincoln Electric AC-225-GLM Instrukcja

22 Września 2024
Lincoln Electric

Lincoln Electric HydroGuard Rod Oven 350 Instrukcja

22 Września 2024
Lincoln Electric

Lincoln Electric Helix T55 Weld Head Instrukcja

22 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024