Instrukcja obsługi LiftMaster 041A6569

LiftMaster Niesklasyfikowane 041A6569

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla LiftMaster 041A6569 (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
Be sure power is not connected to the garage door opener
BEFORE installing the safety reversing sensor.
To prevent SERIOUS INJURY or DEATH from a closing garage
door:
• Correctly connect and align the safety reversing sensor. This
required safety device MUST NOT be disabled.
• Install the safety reversing sensor so beam is NO HIGHER
than 6" (15 cm) above garage floor.
Safety Sensor Brackets
Model 41a6569
Be sure power to the opener is disconnected.
The sending eye transmits an invisible light beam to the receiving
eye. The units can be installed on either side of the garage door as
long as the sun never shines directly into the receiving eye lens.
Look at the label on the connector end of each case to identify the
sensors.
The brackets must be connected and fastened so that the sending
and receiving eyes face each other as shown in Figure 1.
If an obstruction breaks the light beam while the garage door is
closing, the door will stop and reverse to full open position, and
the opener lights will fl ash for 5 seconds.
The brackets must be securely fastened to a solid surface such as
the studs on either side of the door, or add a piece of wood at each
location if installing in masonry construction.
The invisible light beam path must be unobstructed. No part of the
garage door (or door tracks, springs, hinges, rollers or other
hardware) can interrupt the beam while the door is closing. If it
does, use a piece of wood to build out each sensor mounting
location to the minimum depth required for light beam clearance.
Invisible Light Beam
Protection Area
Safety Reversing Sensor
6" (15 cm) max. above floor Safety Reversing Sensor
6" (15 cm) max. above floor
Figure 1: Facing the door from inside the garage
2
Install the Safety Reversing Sensor
Figures 2 and 3 show assembly of brackets and "C" wrap based on
the recommended installation of the sensors on each side of the
garage door as shown on page 1. Figures 4 and 5 are variations
which may fi t your installation requirements better.
Make sure the wraps and brackets are aligned so the sensors
will face each other across the garage door.
• Fasten the "C" wraps to the mounting brackets having square
holes, using the hardware shown in Figure 2.
• Connect each assembly to a slotted bracket, using the hardware
shown in Figure 3.
NOTE: the alignment of the brackets for left and right sides of
the door.
• Finger tighten the lock nuts.
• Use bracket mounting holes as a template to locate and drill (2)
3/16" diameter pilot holes on both sides of the garage door, 4"- 6"
above the fl oor (See warning on but not exceeding 6" (15 cm).
page 1.)
• Attach bracket assemblies with 1/4"x1-1/2" lag screws as shown
in Figure 3.
• Adjust right and left side bracket assemblies to the same distance
out from the mounting surface. Make sure all door hardware
obstructions are cleared. Tighten the nuts securely.
Garage
Floor
Inside
Garage
Wall
Alternate Floor Mount
Mounting Bracket
with Slot
Mounting Bracket
with Square Holes
"C" Wrap
Sensor
Indicator Light
Attach with
concrete anchors
(not provided)
"C" Wrap
Inside
Garage
Wall
Mounting Bracket
with Square Holes
Mounting Bracket
with Slot
Alternate Wall Mount
Sensor
Garage
Floor
Indicator Light
Mounting Bracket
with Slot
1/4"-20
Lock Nuts
1/4x1-1/2"
Lag Screws 1/4-20x1/2" Carriage Bolts
(with square shoulder)
Inside
Garage
Wall
"C" Wrap
Mounting Bracket
with Square Holes
Mounting Bracket
With Square Holes
#10-32x3/8"
Screws
"C" Wrap
#10-32
Lock Nuts
Figure 2
Figure 3
Figure 4
Figure 5
Lag Screw 1/4x1-1/2"
Screw
#10-32x3/8"
Lock Nut
#10x32
Staples Carriage Bolts
1/4"-20x1/2"
Lock Nut
1/4"-20
HARDWARE SHOWN ACTUAL SIZE
3
ALIGNING THE SAFETY REVERSING SENSORS
1/4-20x1-1/2"
Hex Bolt
"C" Wrap Wire
Safety Reversing Sensor
Wing Nut
Invisible Light Beam
Protection Area
Safety Reversing Sensor
Safety Reversing Sensor
Connect Wire to
Opener Terminals
Bell Wire
Bell Wire
Indicator Light
OPENER TERMINAL SCREWS
Sensor
Connections
Wall Control
Connections
(dotted line)
1 2 3
Figure 6
TROUBLESHOOTING THE SAFETY REVERSING SENSORS
1. If the sending eye glow steadily indicator light does not after
installation, check for:
• Electric power to the opener.
• A short in the white or white/black wires. These can occur at
staples, or at opener connections.
• Incorrect wiring between sensors and opener.
• A broken wire.
2. If the sending eye glows steadily indicator light but the
receiving eye indicator light doesn’t:
• Check alignment.
• Check for an open wire to the receiving eye.
3. If the receiving eye indicator light is dim, realign either sensor.
NOTE: When the invisible beam path is obstructed or misaligned
while the door is closing, the door will reverse. If the door is
already open, it will not close. The opener lights will blink 10
times.
• Center each sensor unit in a “C” wrap with lenses pointing
toward each other across the door.
• Secure Safety Reversing Sensors with the hardware shown In
Figure 6. Finger tighten the wing nut on the to receiving eye
allow for fi nal adjustment. Securely tighten the sending eye
wing nut.
• Run wires from both Safety Reversing Sensors to the opener
as shown. Use insulated staples to secure the wire to the wall
and ceiling.
• Connect both sets of wires to the opener terminals as shown
(depending upon your model).
• Plug in the opener. If your opener has the Multi-Function Door
Control, make sure the Lock Feature is off. Indicator lights in
both the and will steadily if sending receiving eyes glow
connections and alignment are correct. If the indicator light is
off the (and the invisible light beam path is not receiving eye
obstructed), alignment is required.
• Loosen the wing nut to allow slight rotation of receiving eye
unit. Adjust Safety Reversing Sensor vertically and horizontally
until the indicator light with a steady light.glows
• When indicator lights are in both units, glowing steadily
tighten the wing nut in the unit.receiving eye
1/4-20x1-1/2"
Hex Bolt Wing Nut
HARDWARE SHOWN ACTUAL SIZE
- -Finished Ceiling

Specyfikacje produktu

Marka: LiftMaster
Kategoria: Niesklasyfikowane
Model: 041A6569

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z LiftMaster 041A6569, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane LiftMaster

LiftMaster

LiftMaster CAPXLV2MC Instrukcja

7 Października 2024
LiftMaster

LiftMaster CAPXSHOOD Instrukcja

29 Września 2024
LiftMaster

LiftMaster 041DJ003MC Instrukcja

25 Września 2024
LiftMaster

LiftMaster myQ-SGC2WCH Instrukcja

23 Września 2024
LiftMaster

LiftMaster CAPXS Instrukcja

23 Września 2024
LiftMaster

LiftMaster 041D8006-1 Instrukcja

22 Września 2024
LiftMaster

LiftMaster IHSL24UL Instrukcja

22 Września 2024
LiftMaster

LiftMaster LJ8900W Instrukcja

22 Września 2024
LiftMaster

LiftMaster 041A7767 Instrukcja

22 Września 2024
LiftMaster

LiftMaster 41K4629 Instrukcja

22 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024