Instrukcja obs艂ugi Lanzar Vibe 426
Przeczytaj poni偶ej 馃摉 instrukcj臋 obs艂ugi w j臋zyku polskim dla Lanzar Vibe 426 (9 stron) w kategorii Autoradio. Ta instrukcja by艂a pomocna dla 3 os贸b i zosta艂a oceniona przez 2 u偶ytkownik贸w na 艣rednio 4.5 gwiazdek
Strona 1/9
Viberant Owner鈥檚 Manual- 1
12
3
765
Congratulations on your purchase of a Lanzar Viberant amplifier. You have purchased a quality product designed
and engineered to give you many years of uncompromised musical service. VIBE amplifiers are designed with
the latest technology available, which provides headroom for even the most demanding peaks and dynamic ranges
found on modern CD's and recordings.
TABLE OF CONTENTS
System Wiring
6. 2 channel stereo
7. 2 channel bridged mode
8. 2 channel tri-mode
9. 2 channel triamp system
10. 4 channel stereo
11. 4 channel bridged mode
12. 4 channel tri-mode
13. Precautions
14.Troubleshooting
15.Notes
1. INPUT LEVEL CONTROLS
Enables the matching of input levels to the output levels from
head unit (or other signal source).
2. CROSSOVER MODE SELECTOR
Determines the mode of built-in crossover:
low pass (permits only low frequency signals to pass to speakers),
high pass (permits only high frequency signals to pass to speakers),
or flat.
3. BASS BOOST CONTROL
With a bass boost switch engaged, the bass level is increased
approx 18dB.
4. REMOTE BASS BOOST
Plug in the remote bass boost control wire in here
5. POWER & PROTECTION INDICATORS
Provide instant information on status of amplifier, including
short-circuit and thermal overload alerts.
6. HIGH PASS FILTER (HPF)
When Crossover Mode Selector is in High Pass Mode, this control
limits the frequencies which will be distributed to the speakers
to those below the value to which this is set within the range 80-
2.5KHz.
7. LOW PASS FILTER (LPF)
When Crossover Mode Selector is in Low Pass Mode, this control
limits the frequencies which will be distributed to the speakers
to those below the value to which this is set within the range 35-
400Hz.
Table of Contents
Feature and Controls
1. VIBE 226/236/246/256/266/276/286
2. VIBE 416/426/436
3. Installation
4. Specifications
Features and Control
s
Viberant Owner鈥檚 Manual
VIBE 226/236/246/256/266/276/28
6
4
Viberant Owner鈥檚 Manual- 3
1. REMOTE BASS BOOST
Plug in the remote bass boost control wire in here
2. INPUT LEVEL CONTROLS
Enables the matching of input levels to the output levels from
head unit (or other signal source).
3. CROSSOVER MODE SELECTOR
Determines the mode of built-in crossover:
low pass (permits only low frequency signals to pass to speakers),
high pass (permits only high frequency signals to pass to speakers),
or flat.
4. BASS BOOST CONTROL
With a bass boost switch engaged, the bass level is increased
approx 18dB.
5. POWER & PROTECTION INDICATORS
Provide instant information on status of amplifier, including
short-circuit and thermal overload alerts.
6. HIGH PASS FILTER (HPF)
When Crossover Mode Selector is in High Pass Mode, this control
limits the frequencies which will be distributed to the speakers
to those below the value to which this is set within the range 80-
2.5KHz.
7. LOW PASS FILTER (LPF)
When Crossover Mode Selector is in Low Pass Mode, this control
limits the frequencies which will be distributed to the speakers
to those below the value to which this is set within the range 35-
400 Hz.
1. Find a suitable location in the vehicle to mount the amplifier.
2. Make sure there is sufficient air flow around the intended mounting location.
3. Bolt the amplifier to the mounting surface.
4. Connect the power ground terminal to the nearest point on the chassis of the car. Keep this ground wire less than one meter (39")
in length. Use 8 gauge wire.
5. Connect the remote terminal to the remote output of the head unit using 14 gauge wire.
6. Connect an empty fuse holder within 300mm (12") of the battery and run 8 gauge of larger high quality cable from this fuse to the
amplifier location.
7. Make sure there is no fuse in this fuse holder. Then make the connection to the "BATT" connection on the amplifier.
8. If multiple amplifiers are being used, use cables (each with its own fuse at the battery) or a #0 or #2 cable from the fuse holder at
the battery to a distribution block at or near the amplifier's location.
9. Connect all line inputs and outputs using high-quality RCA-RCA cables.
10. Insert fuse(s) at the battery fuse holder(s).
11. Recheck all connections before powering up.
12. Set all level controls to their least sensitive positions and set all crossover controls, switches, etc. to the desired frequency or
position.
13. Once the system is powered up, set the volume control on the head unit to about the 2 o'clock position, and then set all the
amplifiers' level controls for maximum output level.
14. Further fine tuning of the various controls may be necessary to obtain the desired results.
Viberant Owner鈥檚 Manual2 -
Features and Controls Installatio
n
VIBE 416/426/436
5 234762 3 476
1
Specyfikacje produktu
| Marka: | Lanzar |
| Kategoria: | Autoradio |
| Model: | Vibe 426 |
Potrzebujesz pomocy?
Je艣li potrzebujesz pomocy z Lanzar Vibe 426, zadaj pytanie poni偶ej, a inni u偶ytkownicy Ci odpowiedz膮
Instrukcje Autoradio Lanzar
13 Wrze艣nia 2024
11 Wrze艣nia 2024
3 Wrze艣nia 2024
3 Wrze艣nia 2024
1 Wrze艣nia 2024
21 Sierpnia 2024
Instrukcje Autoradio
- Autoradio Sony
- Autoradio AEG
- Autoradio Pioneer
- Autoradio Philips
- Autoradio SilverCrest
- Autoradio JBL
- Autoradio Scott
- Autoradio Opel
- Autoradio Panasonic
- Autoradio Muse
- Autoradio Nedis
- Autoradio Medion
- Autoradio Boss
- Autoradio Lenco
- Autoradio Marquant
- Autoradio Jensen
- Autoradio Skoda
- Autoradio Blaupunkt
- Autoradio Volvo
- Autoradio Dual
- Autoradio Grundig
- Autoradio Hyundai
- Autoradio Smart
- Autoradio Kenwood
- Autoradio Alpine
- Autoradio JVC
- Autoradio Ultimate
- Autoradio Mercedes-Benz
- Autoradio Biltema
- Autoradio Auna
- Autoradio OneConcept
- Autoradio Pure
- Autoradio Zenec
- Autoradio Clarion
- Autoradio Fusion
- Autoradio Magnat
- Autoradio Pyle
- Autoradio VDO
- Autoradio Harman Kardon
- Autoradio Aiwa
- Autoradio AKAI
- Autoradio Clatronic
- Autoradio Kicker
- Autoradio Mac Audio
- Autoradio Denver
- Autoradio Hertz
- Autoradio Trevi
- Autoradio Overmax
- Autoradio Sencor
- Autoradio Ground Zero
- Autoradio Rockford Fosgate
- Autoradio Daewoo
- Autoradio Crunch
- Autoradio Varta
- Autoradio Audison
- Autoradio Tevion
- Autoradio Caliber
- Autoradio MB Quart
- Autoradio Tokai
- Autoradio Adcom
- Autoradio Autovision
- Autoradio Roadstar
- Autoradio MT Logic
- Autoradio Axton
- Autoradio Soundstream
- Autoradio VDO Dayton
- Autoradio Watssound
- Autoradio Cartronix
- Autoradio Mtx Audio
- Autoradio ESX
- Autoradio RetroSound
Najnowsze instrukcje dla Autoradio
19 Wrze艣nia 2024
19 Wrze艣nia 2024
18 Wrze艣nia 2024
18 Wrze艣nia 2024
18 Wrze艣nia 2024
18 Wrze艣nia 2024
18 Wrze艣nia 2024
18 Wrze艣nia 2024
18 Wrze艣nia 2024
18 Wrze艣nia 2024