Instrukcja obsługi La Crosse Technology 308-1410GR

La Crosse Technology termometr 308-1410GR

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla La Crosse Technology 308-1410GR (3 stron) w kategorii termometr. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

Wireless Thermometer

Model: -1410GR | Instruction Manual 308

This Wireless Thermometer features: indoor/outdoor temperature

with MIN/MAX readings in Fahrenheit or Celsius, outdoor

temperature trend arrow, and manual set time. Wireless

transmission range of over 200 feet (60 meters) in open air, from

transmitter to wireless thermometer.

SETUP INSTRUCTIONS STEP BY STEP

STEP 1:

Remove battery cover from the Wireless

Thermometer.

Insert 2 NEW AA batteries (not included) into

the back of the wireless thermometer. Observe

the correct polarity (see marking inside the

battery compartment).

The wireless thermometer will light up and

show, indoor temperature, and time (12:00).

STEP 2:

Ensure that the transmitter is within 10 feet of the

wireless thermometer.

Remove battery cover from TX141-B transmitter: Slide

the battery cover down and lift o the front.

Insert 2 NEW AA batteries into the transmitter.

Observe the correct polarity.

Within 3 minutes the Wireless Thermometer will show

readings in the outdoor temperature area on the LCD.

Note: Allow t wireless thermometer and the he

transmitter to stay within 10 feet of each other for the rst 15

minutes of set up.

Do Not Mix Old and New Batteries

Do Not Mix Alkaline, Standard, Lithium or Rechargeable

Batteries

TRANSMITTER SIGNAL STRENGTH INDICATOR

 After the batteries are inserted, the wireless thermometer will

search for the outdoor temperature transmitter for 3 minutes.

 The antenna symbol will ash during reception, and

temperature display will be dashes “---“.

 No antenna symbol will show during transmitter synchronization.

 If synchronization fails once, the antenna will lose one bar.

 If synchronization fails twice, the antenna will lose two bars.

 If RF (radio frequency) reception fails ve times, the antenna

symbol will be shown as .

 The antenna will show full display with successful RF

(radio frequency) reception.

TROUBLE SHOOTING

If the wireless thermometer does not display the outdoor

temperature after 3 minutes, remove the batteries from both units

and start the setup process again.

If the outdoor temperature does not show up after a second

attempt, please slide open the battery cover of the outdoor

transmitter to reveal the TX button. Push down on the TX button

for 3 seconds to send a wireless signal to the wireless

thermometer.

For optimal 433 MHz signal reception, the outdoor transmitter

should be placed within 200 feet (60 meters) from the wireless

thermometer.

SET TIME

The SET/°F/°C button moves through the program menu. The

MIN/MAX/+ button changes the value.

12/24-HOUR TIME: Hold the SET/°F/°C button for 2 seconds.

12H will ash. Press and release the MIN/MAX/+ button to select

24-hour time format. Press and release the SET button once to

move to the hour.

: The Hour will ash. Press and release the MIN/MAX/+ HOUR

button until the correct hour is shown. Press and release the SET

button once to move to the minutes.

MINUTES: The Minutes will ash. Press and release the

MIN/MAX/+ button until the correct minutes are displayed. Press

and release the SET button once more to exit the program menu.

FAHRENHEIT/CELSIUS

Press the SET/°F/°C button to

select Fahrenheit or Celsius

temperature readout.

MAXIMUM/MINIMUM TEMPERATURE READINGS

The Wireless Thermomet will show the daily minimum and er

maximum temperatures each day starting at midnight (12:00 AM).

The temperature station automatically resets the min/max

temperatures at midnight (12:00 AM).

VIEW MINIMUM: Press MAX/MIN button to show the minimum

temperature record.

RESET MINIMUM: With the minimum temperatures displayed,

press and hold the MAX/MIN key for 2 seconds to manually clear the

MIN records in memory.

VIEW MAXIMUM: Press MAX/MIN key again, to show the

maximum temperature records. In maximum memory display mode,

RESET MINIMUM: With the maximum temperatures displayed,

press and hold the MAX/MIN key for 2 seconds to manually clear the

MAX records in memory.

TEMPERATURE TREND ICONS

The outdoor temperature trend indicators will update every 30

minutes or less. These trends represent temperature changes over

the past three hours.

Temperature rising more than 2°F / 1°C in the past three

hours

Temperature has not changed more than 2°F 1°C in the /

past three hours.

Temperature falling more than 2°F 1°C in the past three /

hours

The temperature trend indicators are shown next to the indoor

temperature and outdoor temperature readings.

POSITIONING THE TEMPERATURE TRANSMITTER

The remote temperature transmitter should be mounted vertically to

avoid damage. Place both units in the desired locations, and wait

approximately 1-hour before permanently mounting the transmitter

to ensure that there is proper reception. The outdoor temperature

transmitter is water resistant, not waterproof and should not be

placed anywhere it will become submerged in water or subject to

standing water or snow.

WALL MOUNT

Choose a location for the transmitter that is within range of the

Wireless Thermometer and under an overhang for accuracy.

Option 1:

Install one mounting screw (not included) into a wall

leaving approximately ½ of an inch (12.7mm)

extended.

Place the transmitter onto the screw, using the

hanging hole on the backside.

Gently pull the transmitter down to lock the screw into

place.

Option 2:

Insert the mounting screw (not included) through the front of the

transmitter and into the wall.

Tighten the screw to snug (do not over tighten).

To achieve a true temperature reading, mount where direct

sunlight cannot reach the outdoor transmitter. Mount the outdoor

transmitter on a North-facing wall or in any well shaded area.

Under an eave or deck rail work well. The maximum transmitting

range in open air is over 200-feet (60 meters). Obstacles such as

walls, windows, stucco, concrete, and large metal objects can

reduce the range. Place the transmitter at least 6 feet in the air to

improve signal transmission.

SPECIFICATIONS

Indoor Temperature:

Range: 32°F to 122°F (0°C to + 50°C)

Resolution: 0.2°F/0.1°C

Outdoor Temperature:

Range: -40°F to 140°F (-40°C to + 60°C)

Resolution: 0.2°F/0.1°C

Distance: Over 200 ft. (60 meters)

RF 433MHz (open air)

Power:

Wireless Thermometer: 2-AA LR6 Alkaline battery

(not include d)

TX141-B Transmitter: 2-AA LR6 Alkaline battery

(not included)

Battery Life: Battery life is over 24 months when

using reputable Alkaline battery

brands

Dimensions:

308-1410GR

Wireless Thermometer: 3”L x 1.36”W x 4.17”H

(76 x 34 x 106 ) mm

TX141-B Transmitter: 5.08” H x 1.58” W x 0.83” D

(129 x 40.13 x 21mm)

CARE AND MAINTENANCE

Do Not Mix Old and New Batteries

Do Not Mix Alkaline, Standard, Lithium or Rechargeable Batteries

Do not expose the Wireless Thermometer: to extreme temperatures,

vibration or shock.

Keep wireless thermometer dry.

Clean with a soft damp cloth. Do not use solvents or scouring agents.

The wireless thermometer is not a toy. Keep it out of reach of children.

The wireless thermometer is not to be used for medical purpose or for

public information, but is determined for home use only.

The specications of this product may change without prior notice.

Improper use or unauthorized opening of housing will void the warranty.

If the unit does not work properly, change the batteries.

WARRANTY INFORMATION

La Crosse Technology, Ltd provides a 1-year limited warranty on this product against

manufacturing defects in materials and workmanship. This limited warranty begins on

the original date of purchase, is valid only on products purchased and used in North

America and only to the original purchaser of this product. To receive warranty

service, the purchaser must contact La Crosse Technology, Ltd for problem

determination and service procedures. Warranty service can only be performed by a

La Crosse Technology, Ltd authorized service center. The original dated bill of sale

must be presented upon request as proof of purchase to La Crosse Technology, Ltd

or La Crosse Technology, Ltd’s authorized service center.

La Crosse Technology, Ltd will repair or replace this product, at our option and at no

charge as stipulated herein, with new or reconditioned parts or products if found to be

defective during the limited warranty period specied above. All replaced parts and

products become the property of La Crosse Technology, Ltd and must be returned to

La Crosse Technology, Ltd.

Replacement parts and products assume the remaining original warranty, or ninety

(90) days, whichever is longer. La Crosse Technology, Ltd will pay all expenses for

labor and materials for all repairs covered by this warranty. If necessary repairs are

not covered by this warranty, or if a product is examined which is not in need or

repair, you will be charged for the repairs or examination.

The owner must pay any shipping charges incurred in getting your La Crosse

Technology, Ltd product to a La Crosse Technology, Ltd authorized service center.

Your La Crosse Technology, Ltd warranty covers all defects in material and

workmanship with the following specied exceptions: (1) damage caused by accident,

unreasonable use or neglect (including the lack of reasonable and necessary

maintenance); (2) damage occurring during shipment (claims must be presented to

the carrier); (3) damage to, or deterioration of, any accessory or decorative surface;

(4) damage resulting from failure to follow instructions contained in your owner’s

manual; (5) damage resulting from the performance of repairs or alterations by

someone other than an authorized La Crosse Technology, Ltd authorized service

center; (6) units used for other than home use (7) applications and uses that this

product was not intended or (8) the products inability to receive a signal due to any

source of interference.

This warranty covers only actual defects within the product itself, and does not cover

the cost of installation or removal from a xed installation, normal set-up or

adjustments, claims based on misrepresentation by the seller or performance

variations resulting from installation-related circumstances.

LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR

INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES

ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT.

THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR

PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF

CHILDREN’S REACH.

This warranty gives you specic legal rights. You may also have other rights specic

to your State. Some States do no allow the exclusion of consequential or incidental

damages therefore the above exclusion of limitation may not apply to you.

For warranty work, technical support, or information contact:

La Crosse Technology, Ltd

2817 Losey Blvd. S.

La Crosse, WI 54601

Contact Support: 1-608-782-1610

Product Registration:

www.lacrossetechnology.com/support/register

On the Web at:

www.lacrossetechnology.com/308-1410

Protected under U.S. Patents:

5,978,738, 6,076,044, 6,597,990

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment o and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

This device must not be co-located or operating in conjunction with any other antenna

or transmitter. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference

that may cause undesired operation.

Caution!

The manufacturer is not responsible for any radio or TV interference caused by

unauthorized modications to this equipment. Such modications could void the user

authority to operate the equipment.

duplicated or processed using electronic, mechanical or chemical process without the

written permission of the publisher.

This booklet may contain errors or misprints. The information it contains is regularly

checked and corrections are included in subsequent editions. We disclaim any

responsibility for any technical error or printing error, or their consequences.

All trademarks and patents are recognized.

Specyfikacje produktu

Marka:	La Crosse Technology
Kategoria:	termometr
Model:	308-1410GR
Kolor produktu:	Czarny
Wysokość produktu:	723.9 mm
Szerokość produktu:	1209 mm
Głębokość produktu:	93.9 mm
Waga produktu:	79.4 funtów
W zestawie pilot zdalnego sterowania:	Tak
Certyfikat środowiskowy (zrównoważonego rozwoju):	ENERGY STAR
Moc wyjściowa (RMS):	16 W
Typ HD:	Full HD
Długość przekątnej ekranu:	50 "
Zakres temperatur (eksploatacja):	0 - 40 °C
Zakres wilgotności względnej:	20 - 80 %
Rozdzielczość:	1920 x 1080 px
Natywne proporcje obrazu:	16:9
Pobór mocy w trybie czuwania:	0.9 W
Wejscie Audio (L,P):	2
Pobór mocy:	605 W
Ilość portów HDMI:	2
Port RS-232:	1
Technologia wyświetlacza:	Plasma
Rozmiar plamki:	0.576 x 0.576 mm
Wyście mocy ac:	Tak
Szerokość (bez podstawy):	1209 mm
Głębokość (bez podstawy):	93.9 mm
Wysokość (bez podstawy):	723.9 mm
Zużycie energii (tryb uśpienia):	0.5 W
Bezpieczeństwo:	UL6500 Ver. 2
Zasięg skanowania w poziomie:	15 - 110 kHz
Zasięg skanowania (długość):	48 - 120 Hz
Wejście komponentu wideo (ypbpr/ycbcr):	3
Złożone wejście wideo:	1
Wejście PC (D-Sub):	Tak
Zespolony sygnał wizji:	1
Wyjście audio (prawe/lewe):	2
Wyłącznik czasowy:	Tak
OSD:	Tak
Obsługa funkcji Plug & Play:	Tak
Redukcja hałasu:	Tak
Wejście audio dla PC:	Nie
Wejście cyfrowe audio:	1
Format obrazu:	16:9
Część widoczna ekranu:	1104 x 622.3 mm
Skanowanie progresywne:	Tak
Wymiary (SxGxW) (imperialne):	47.6 x 3.7 x 28.5 "
Tryb gry:	Tak
Wejście S-Video:	1
Filtr grzebieniowy:	3D
Spełniane normy w zakresie emisji elektromagnetycznej:	FCC Part 15 ClAA-b ices-003