Instrukcja obsługi La Crosse Technology 30330

La Crosse Technology Radiobudzik 30330

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla La Crosse Technology 30330 (2 stron) w kategorii Radiobudzik. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

NIGHT VISION® LCD ALARM

Model 30330B

Thank your purchase manufacture you for of this amazing clock. The utmost care has gone into the design and of your clock. Please

read them for reference. these instructions and store a safe place future

Night Vision ® Technology

This This . clock incorporates Night Vision ® Technology a cordless battery operated feature allows you to see the time in dark room.

When level extremely When light is a low the light SENSOR (7) automatically illuminates dim glow behind the digital display. your

eyes darkened time! off the when a adjust in room, you can still see the The sensor automatically turns Night Vision ® glow the room

brightens.

You a can also activate bright backlight display anytime by pressing the SNOOZE/LIGHT bar (3).

TO INSTALL AND REPLACE BATTERIES

The "AA" LCD clock uses three 1.5V batteries. (Not included)

To install and replace the batteries. Please follow the steps below.

1. Remove the battery cover.

2. Insert batteries observing inside the correct polarity (see marking battery compartment).

3. Replace the battery cover.

Note: mix new batteries. mix cadmium) Do not and old Do not ( - alkaline, standard carbon zinc), or rechargeable (nickel

batteries.

TO THE TIME SET

1. Hold AM the TIME SET button (5) and press the HOUR button (1) to your desired hour. Be careful to set the time to or PM

correctly. time is will When PM set. The letter "PM" appear.

2. Hold the TIME SET button (5) again, press the MINUTE button (2) to your desired minute. –

TO SET THE ALARM TIME

1. Hold time ALARM the SET button (6) and press the HOUR button (1) to your desired hour. Be careful to set the to AM or PM

correctly. time is will When PM set, the letter "PM" appear.

2. Hold again, ALARM the SET button (6) press the MINUTE button (2) to your desired minute.

TO TURN THE ALARM ON OR OFF

1. Slide position. ALARM the SWITCH (4) to the "AL.ON" The alarm symbol be (bell) will visible on the display when the alarm is

activated. will 60 The alarm sound for seconds at the selected time.

2. Slide position ALARM the SWITCH (4) to the "AL.OFF" to turn the alarm off permanently.

TO FEATURE USE THE SNOOZE ALARM

Slide the ALARM SWITCH (4) to the "AL.ON" position when the alarm sounds, press the SNOOZEI/LIGHT button (3). The alarm will

stop 5 and sound again after minutes

MAINTENANCE

The batteries should be replaced if the display or alarm becomes weak or dysfunctional. without Store the Clock batteries when not

in cloth clean clock. Do corrosive chemical A use. soft a or paper towel may be used to your not use any cleanser or solutions on the

clock. clock clean Keep the and dry to avoid any problems.

Two Year Warranty (U.S.A.)

Equity products are warranted for two years from the date of consumer purchase against defects in material and workmanship.

During this period such defects will be repaired, or the product will be replaced at Equity’s option. This warranty does not cover

damage caused by misuse or negligence. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OR

FITNESS AND MERCHANTABILITY, ARE LIMITED IN DURATION TO A PERIOD ENDING TWO YEARS FROM DATE OF PURCHASE. Some

states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you. This warranty

gives you specific legal rights and you may also have other rights which vary from State to State.

If your product is not working properly, please send:

- The Product

- a letter explaining the problem

- and $5.00 for postage and handling to:

Equity Warranty Dept.

2817 Losey Blvd. S

La Crosse, WI 54601

For Customer Support, visit:

www.equitybylacrosse.com/support

Always purchase the grade battery suitable the intended use. Replace the the battery those correct size and of most for a all batteries of set at same time. Clean contacts and also of the

device prior Ensure the to battery installation. - batteries are installed correctly with regard to polarity (+and ). Remove batteries from equipment be with is not to used for an extended