Instrukcja obsługi Kurzweil Forte SE

Kurzweil klawiatura Forte SE

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kurzweil Forte SE (18 stron) w kategorii klawiatura. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/18
is guide will help you hook up the Forte SE to your sound system and MIDI system, give you a quick
overview, and show you how to start playing music with the Forte SE. A full manual for the Forte SE can
be obtained in electronic format from www.kurzweil.com.
Specications
Forte SE is Kurzweil’s latest entry in the Forte line of stage pianos. Some of the key specications include:
FlashPlay technology with support for 2GB of Sound ROM
High Denition Japanese Grand Piano and High Denition Electric Piano
ROM sounds included from Kurzweil’s acclaimed PC3 series, KORE64 expansion,
and German D Grand EXP Grand Piano expansion
New Piano String Resonance Simulation
Full KB3 organ simulations with 9 sliders as drawbars
8 Zone MIDI Controller
Space for 1024 Factory and 1024 User Programs and Multis (16 Categories of Programs)
Arpeggiator with dedicated On/O button (1 per Program, up to 8 in Multi Mode)
MP3 player audio input jack
Full 128 voices of polyphony
Hundreds of Eects Chains
®
It’s the
sound
.
®
SE
GETTING STARTED GUIDE
Before You Start…
2
GETTING STARTED GUIDE
Before You Start…
Dont connect anything until you make sure the Forte SE is properly and safely situated. If
your Forte SE keyboard has been out in the cold, give it time to warm up to room temperature
before starting it, since condensation may have formed inside.
Setting up the Forte SE
1. Set the keyboard on a hard, at, level surface.
2. Four adhesive-backed rubber feet are provided with Forte SE. Carefully turn the keyboard
over onto a soft surface, remove the paper backing from the rubber feet and attach them.
NOTE : Unless the instrument will always be used with a keyboard stand,
attachment of the rubber feet is strongly advised. Otherwise protruding
screws will scratch the tabletop.
3. Connect the AC power cord to the Forte SE. Before plugging the cable into the power
outlet, check that the power is compatible with the Forte SE. e Forte SE runs on AC
power and works with voltages from 80-265 volts 50-60 Hz. e voltage level is detected
and set automatically by the Forte SE. If your power source does not have the standard
three hole outlet, you should take the time to install a proper grounding system. is will
reduce the risk of a shock. If your power outlet is not within these ranges it is recommended
you use an appropriate adaptor.
4. Plug the power cable into the wall.
5. Plug the Switch Pedal into the marked SW1 (Sustain) Pedal jack on the Forte SE rear
panel.
6. Connect stereo headphones to the headphone jack on the rear panel or connect the audio
outputs to your mixer or amplier inputs using standard (1/4-inch) audio cables (use the
Left out for Balanced (“TRS” or “Stereo”) cables are recommended if your mixer mono).
or amp supports balanced inputs.
The Rear Panel
Using the Forte SE
3
GETTING STARTED GUIDE
7. Make sure your sound system is at a safe volume level. Also make sure that the Forte SE
Master Volume slider (on the far left side of the front panel) is all the way down.
Using the Forte SE
1. Power up the Forte SE using the power switch on the rear left side of the instrument, and
then raise the Master Volume slider, and mixer/amp volume. Your Forte SE keyboard starts
up in Program Mode by default. Press one of the buttons under the “Modelabel to the
right of the display to switch Modes.
Master Volume Slider Mode Selection
2. If you are connected to a mixing board and hear distortion, reduce the gain level on your
mixing board, or use the pad (a switch that decreases the input audio signal level, typically by
20dB) if it has one.
3. To hear the capabilities of the Forte SE, you can play the demo songs. Press the 13 & 14
Program/Multi buttons simultaneously to listen to a demo song.
4. In Program Mode, scroll through the Programs using the Alpha Wheel, the Previous and
Next buttons, or press a Category button to audition the sounds in the Forte SE. e Forte
SE has short demos for each of the factory Programs. To hear a Program Demo for the
current Program, press the 11 & 12 Program/Multi buttons simultaneously.
The Rear Panel
e power switch and most of the Forte SE connections are located on the rear panel.


Specyfikacje produktu

Marka: Kurzweil
Kategoria: klawiatura
Model: Forte SE

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Kurzweil Forte SE, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje klawiatura Kurzweil

Kurzweil

Kurzweil SP1 Instrukcja

7 Października 2024
Kurzweil

Kurzweil SP4S-8 Instrukcja

22 Września 2024
Kurzweil

Kurzweil K2700 Instrukcja

22 Września 2024
Kurzweil

Kurzweil PC3 Instrukcja

22 Września 2024
Kurzweil

Kurzweil PC3A8 Instrukcja

22 Września 2024
Kurzweil

Kurzweil K2600 Instrukcja

22 Września 2024
Kurzweil

Kurzweil K2600R Instrukcja

21 Września 2024
Kurzweil

Kurzweil PC4-7 Instrukcja

21 Września 2024
Kurzweil

Kurzweil KP-120A Instrukcja

21 Września 2024
Kurzweil

Kurzweil SP7 Instrukcja

21 Września 2024

Instrukcje klawiatura

Najnowsze instrukcje dla klawiatura

Speed-Link

Speed-Link VIRTUIS Instrukcja

14 Października 2024
Speed-Link

Speed-Link ATMOS Instrukcja

13 Października 2024
Targus

Targus Thura GXT 860 Instrukcja

13 Października 2024
Roland

Roland Fantom G8 Instrukcja

11 Października 2024
Yamaha

Yamaha Portatone PSR-160 Instrukcja

10 Października 2024
Roland

Roland E-30 Instrukcja

10 Października 2024
Yamaha

Yamaha Electone B-45 Instrukcja

10 Października 2024
Urban Factory

Urban Factory GWK01UF Instrukcja

9 Października 2024
Trust

Trust 24645 Instrukcja

9 Października 2024