Instrukcja obsługi Korg NTS-2 oscilloscope kit

Korg Sprzęt DJ-ski NTS-2 oscilloscope kit

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Korg NTS-2 oscilloscope kit (4 stron) w kategorii Sprzęt DJ-ski. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

Table of Contents

Introduction .............................................................................2

Main features of this unit .........................................................2

Part names and functions ........................................................2

Making connections and turning on the power ......................2

Turning the power on/o ...................................................2

Auto power-o function ....................................................2

Four operating modes .............................................................2

Oscilloscope mode (SCOPE) ..............................................................................................2

Function generator mode (WAVE) ..................................................................................2

Spectrum analyzer mode (FFT) ........................................................................................2

Tuner mode (TUNER) ..........................................................................................................2

Basic operations .......................................................................3

Oscilloscope mode (SCOPE) .....................................................3

Explanations of each parameter ........................................3

Function generator mode (WAVE) ...........................................3

Button 1 (button 3): explanations of each parameter ........3

Button 2 (button 4): explanations of each parameter .......3

CATEGORY = Oscillator .......................................................................................................3

CATEGORY = LFO .................................................................................................................3

CATEGORY = Noise ..............................................................................................................3

CATEGORY = Pulse ..............................................................................................................3

CATEGORY = Envelope .......................................................................................................3

Spectrum analyzer mode (FFT) ................................................3

Explanations of each parameter ........................................3

Tuner mode (TUNER) ................................................................4

Explanations of each parameter ........................................4

Global mode .............................................................................4

1: Input ....................................................................................................................................4

2 : SETTINGS ..........................................................................................................................4

3 : SETTINGS ..........................................................................................................................4

Specications ...........................................................................4

E 1

NTS-2 oscilloscope kit

MULTIFUNCTIONAL UTILITY KIT

Owner’s Manual

* All product names and company names are the trademarks or registered trademarks

of their respective owners.

En Introduction

ank you for purchasing the Multifunctional Utility Kit for the Nu:Tekt NTS-2 Os-

cilloscope Kit. To help you get the most out of your purchase, please read this manual

carefully.

Main features of this unit

is product is an assembly kit that you can use to build a digital oscilloscope. Aside

from letting you view audio output waveforms and CV signals, this oscilloscope func-

tions as a spectrum analyzer, oers a built-in tuner for tuning analog synthesizers, and

lets you output LFO, CV and other signals with its function generator.

Part names and functions

5 6 7 8 9

3 4

(Bottom)

1. Mode button

Use this button to switch between operating modes. Each time you press the button,

the mode changes.

a. Oscilloscope (SCOPE)

b. Function generator (WAVE)

c. Spectrum analyzer (FFT)

d. Tuner (TUNER)

e. Global (GLOBAL)

2. Buttons 1–4

e functions assigned to these buttons dier, depending on the operating mode.

3. START/STOP button

Starts and stops measurement. In function generator mode, this is also used to

output waveforms to an external device.

4. Value knob

Press to select a sub-menu, and turn to edit the selected parameter.

5. INPUT 1, 2 jacks

Connect a stereo (or mono) mini cable here to input the signal you wish to measure.

is lets you monitor the audio output from your musical instrument or input a CV

signal.

6. THRU 1, 2 jacks

Used as a thru out for the signal input from the INPUT 1 and 2 jacks.

7. OUTPUT 1, 2 jacks

Outputs the function generator signal.

Connect these jacks to your device with monaural mini plugs.

8. USB (Type-C) port

Use the included USB cable to connect this unit to the USB port on your computer

or to a commercially available USB standards-compliant AC adapter (at least 5 V

DC 550 mA).

9. Power button

Turns the power on and o. Hold this button down for approximately one second to

turn the power o.

10. Battery compartment

Making connections and turning on the power

USB (type portC)

USB cable

SIGNAL IN

SIGNAL OUT

NTS-2 oscilloscope kit

USB adapter AC

(USB 2.0 compatible)

(commercially available)

Computer

Use the included USB cable to connect this unit to the USB port on your computer

or to a commercially available USB standards-compliant AC adapter (at least 5 V DC

550mA).

Make sure to use the included USB cable.

Use a cable that’s no more than 3 m long when connecting your peripherals to this

unit.

Make sure to use an AC adapter that’s compliant with USB 2.0 standards. Note that

some standards-compliant USB AC adapters might not operate correctly.

Turning the power on/o

Long-press the power button to turn on the unit.

Long-press the power button again to turn the unit o.

Auto power-o function

e Nu:Tekt NTS-2 features an auto power-o function that automatically turns the

unit o aer one hour has elapsed without the knob, switches, buttons or other controls

being operated. e auto power-o function is enabled by factory default.

Auto power-o can be disabled using the steps below.

1. Use the mode button to enter global mode.

2. Press button 4 (SETTINGS: Power) a number of times to select “Auto Power

O(USB)” or “Auto Power O(Battery)”.

3. Turn the value knob to change the value to “innite”.

Four operating modes

Oscilloscope mode (SCOPE)

You can view the waveforms from up to four input sources. e functions below are

assigned to buttons 1–4.

1: DISPLAY: Switches between input signals.

2: VERTICAL: Sets the display range for the vertical screen direction (voltage).

3: HORIZONTAL: Sets the display range for the horizontal screen direction (time).

4: TRIGGER: Sets which change in input signal causes the display to update.

Function generator mode (WAVE)

In this mode, signal is output from the OUTPUT 1 and 2 jacks. ese outputs can be

used even while an input signal is being received. You can use the START/STOP button

to turn the waveform output on/o, continuously output the waveform by holding

down the button, or output only one cycle of the waveform (one-shot) by just pressing

the button. e functions below are assigned to buttons 1–4.

1: CATEGORY: Selects the waveform for OUTPUT 2, sets the level and so forth.

2: EDIT: Congures the detailed settings for the OUTPUT 2 waveform.

3: CATEGORY: Selects the waveform for OUTPUT 1, sets the level and so forth.

4: EDIT: Congures the detailed settings for the OUTPUT 1 waveform.

Spectrum analyzer mode (FFT)

is mode lets you observe the frequency characteristics of the input signal, by using a

spectrum analyzer that employs an FFT (fast Fourier transform) algorithm. e func-

tions below are assigned to buttons 1–4.

1: INPUT: Switches between input signals.

2: VERTICAL: Sets the display range for the vertical screen direction (voltage).

3: HORIZONTAL: Sets the display range for the horizontal screen direction (time).

4: TRIGGER: Sets which change in input signal causes the display to update. Nor-

mally, this is set to AUTO.

Tuner mode (TUNER)

is mode measures the pitch of the input signal from the oscillator of an analog syn-

thesizer or other source. You can select between a horizontal meter and a needle-type

(VU) meter view. e functions below are assigned to buttons 1–4.

1: DISPLAY: Selects the tuner display mode.

2: INPUT: Switches between input signals to measure.

3: CALIB: Adjusts the pitch lower or higher than the reference pitch of A=440Hz.

You can adjust the pitch within a range of 410–480 Hz.

4: SCOPE: Switches the oscilloscope display on/o.

Basic operations

1. Each time you press buttons 1–4, the parameter assigned to the button in question

changes one at a time and is shown in the popup screen in the display.

2. Once the desired parameter is shown, turn the value knob to edit the value.

3. Measurement starts/stops with each press of the START/STOP button.

is product is a multi-tool intended for use with musical instruments. Do not use

this product for anything under than its intended purpose, such as for calibrating

measurement devices and so on.

Oscilloscope mode (SCOPE)

Oscilloscope mode lets you monitor the input signals coming from the four input sourc-

es (INPUT 1, 2 L/R).

Use VERTICAL to set the voltage range for the vertical screen direction. For example, a

“5V” setting will display a 5 V voltage for each mark on the vertical axis.

Use HORIZONTAL to set the time scale in the horizontal screen direction.

Use the DISPLAY setting to select the inputs shown on the oscilloscope, display multiple

inputs separately or stacked on top of each other, or to display two inputs as an image

for comparing two dierent signals. To compare two signals with each other, set the

vertical and horizontal directions to the same setting.

Use TRIGGER to set the timing at which the scope measures the signal input.

Explanations of each parameter

Button#/NAME Pop Up Enc. Push Enc. Value

1: DISPLAY Overlay 1 ch mode 1L, 1R, 2L, 2R

2 ch mode 1L-1R, 1L-2L, 1R-2R, 2L-2R

4 ch mode ---

Separate-2 2 ch mode 1L-1R, 1L-2L, 1R-2R, 2L-2R

4 ch mode ---

Separate-4 --- ---

X-Y XY 1L-1R, 1L-2L, 1R-2R, 2L-2R

XY-TY overlay 1L-1R, 1L-2L, 1R-2R, 2L-2R

2: VERTICAL 1L Input mode

(DCnAC)

Vertical range:

10 mV–10 V/div (10 m, 20 m,

50 m, 0.1, 0.2, 0.5, 1, 2, 5, 10)

3: HORIZONTAL Sec/Div --- Horizontal range:

50us–1 s/div (50, 100, 200,

500, 1 m, 2 m, 5 m, 10 m,

20m, 50 m, 100 m, 200 m,

500 m, 1)

Position Set position to zero Change center position

4: TRIGGER Auto Set trigger level to

zero

Set trigger level:

−5.00 V–5.00 V (0.01 V step)

Rise

Fall

Rise single

Fall single

START/STOP --- --- Oscilloscope RUN/STOP

* Buttons 1–4 + value knob (when the popup is shown): edits the popup item.

* Button 4 + value knob: push to edit what is triggered.

* START/STOP button: controls the run/stop and single mode standby.

Function generator mode (WAVE)

Use this mode to output oscillator /noise signals that can be handled as audio, or to out-

put LFO/PULSE/envelope signals that can be handled as CV signals. OUTPUT 1 and 2

are completely independent, and dierent categories can be selected and used for each.

Button 1 (button 3): explanations of each parameter

Button#/NAME Pop Up Enc. Push Enc. Value

1 (3): CATEGORY

CATEGORY ---

Oscillator

LFO

Noise

Pulse

Envelope

VOLUME Vpp n dBu Set Output Level

CYCLE MODE ---

Cont.

1-Shot

Push

INPUT

MONITOR ---

O

Input 1L

Input 1R

Input 2L

Input 2R

Button 2 (button 4): explanations of each parameter

CATEGORY = Oscillator

Button#/NAME Pop Up Enc. Push Enc. Value

2: EDIT

WAVE TYPE --- Sine, Square, Tri, Saw-Rise, Saw-

Fall

PITCH Frequency n Note 0.01–10.00 kHz / C-0 – G9

SHAPE Set shape to 50% 0–100%

PHASE Set phase to 0° −180 – +180°

CATEGORY = LFO

Button#/NAME Pop Up Enc. Push Enc. Value

2: EDIT

WAVE TYPE --- Sine, Square, Tri, Saw-Rise, Saw-

Fall

FREQUENCY Frequency n BPM 0.01–10.00 kHz / 0.5–600.0 BPM

DIRECTION Set direction to ± −, ±, +

PHASE Set phase to 0° −180 – +180°

CATEGORY = Noise

Button#/NAME Pop Up Enc. Push Enc. Value

2: EDIT

WAVE TYPE --- White, Pink

TIME Period n BPM 1 ms–10.0 s / 0.5–600.0 BPM

--- --- ---

DUTY Set duty to 100% 0–100%

CATEGORY = Pulse

Button#/NAME Pop Up Enc. Push Enc. Value

2: EDIT

WAVE TYPE --- Positive, Negative

TIME Period n BPM 1 ms–10.0 s / 0.5–600.0 BPM

--- --- ---

DUTY Set duty to 50% 0–100%

CATEGORY = Envelope

Button#/NAME Pop Up Enc. Push Enc. Value

2: EDIT

WAVE TYPE --- Linear, Exp.

TIME Period n BPM 1 ms–10.0 s / 0.5–600.0 BPM

SHAPE Set shape to 50% 0–100%

DUTY Set duty to 100% 0–100%

Spectrum analyzer mode (FFT)

Spectrum analyzer mode uses an FFT (fast Fourier transform) function that lets you

monitor the reference waveform along with a frequency spectrogram of the input

signal. is is useful for seeing where the eects of a lter or the changes you make to a

waveform appear in the frequency bands.

Explanations of each parameter

Button#/NAME Pop Up Enc. Push Enc. Value

1: INPUT -- Input mode: ACnDC 1L, 1R, 2L, 2R

2: VERTICAL INPUT 1L Input mode: ACnDC VERTICAL RANGE:

10 mV–10 V/div (10 m,

20m, 50 m, 0.1, 0.2, 0.5, 1,

2, 5, 10)

INPUT 1R

INPUT 2L

INPUT 2R

3: HORIZONTAL Sec/Div --- Time range (50 us–1 s/div)

Position Set position to zero Change center position

FFT

Range

--- FFT max Range

(1k–20kHz)

FFT

Position

--- FFT min Range (0–19 kHz)

4: TRIGGER AUTO,

Rise, Fall

Set trigger level to

zero

Set trigger level:

−5.00V–5.00 V (0.01 V step)

START/STOP - - FFT RUN/STOP

* Buttons 1–4 + value knob (when the popup is shown): edits the popup item.

* START/STOP button: controls the run/stop and single mode standby.

Specyfikacje produktu

Marka:	Korg
Kategoria:	Sprzęt DJ-ski
Model:	NTS-2 oscilloscope kit

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Korg NTS-2 oscilloscope kit, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Sprzęt DJ-ski Korg

Korg Rhythm Master Instrukcja

10 Grudnia 2024

Korg PuttRhythm Instrukcja

10 Grudnia 2024

Korg DT-10 Instrukcja

7 Października 2024

Korg OT-120 Instrukcja

27 Września 2024

Korg DTR-2000 Instrukcja

26 Września 2024

Korg CM-200 Instrukcja

23 Września 2024

Korg DTR-1000 Instrukcja

17 Września 2024

Korg A4501 Instrukcja

15 Września 2024

Korg Pitchclip Instrukcja

14 Września 2024

Korg AX1G Instrukcja

14 Września 2024

Instrukcje Sprzęt DJ-ski

Najnowsze instrukcje dla Sprzęt DJ-ski

Fuzzix MBR60 Instrukcja

14 Marca 2025

Omnitronic BOOZ Event Stand Instrukcja

5 Marca 2025

UDG Gear AlphaTheta DDJ-GRV6 Instrukcja

4 Marca 2025

Line 6 Helix Control Instrukcja

11 Stycznia 2025

AlphaTheta DDJ-GRV6 Instrukcja

8 Stycznia 2025

Glorious Record Box 55 Instrukcja

4 Stycznia 2025

Glorious Record Box Display Door Instrukcja

4 Stycznia 2025

Glorious Session Cube XL Instrukcja

4 Stycznia 2025

Glorious Modular Mix Station Instrukcja

4 Stycznia 2025

Glorious Record Box Advanced 110 Instrukcja

4 Stycznia 2025