Instrukcja obsługi Korg GT-120

Korg Sprzęt DJ-ski GT-120

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Korg GT-120 (2 stron) w kategorii Sprzęt DJ-ski. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Precautions

Location

Using the unit in the following locations can result in a malfunction.

• In direct sunlight

• Locations of extreme temperature or humidity

• Excessively dusty or dirty locations

• Locations of excessive vibration

Power supply

Please connect the designated AC adaptor to an AC outlet of the correct voltage. Do

not connect it to an AC outlet of voltage other than that for which your unit is in-

tended.

Interference with other electrical devices

This product contains a microcomputer. Radios and televisions placed nearby may

experience reception interference. Operate this unit at a suitable distance from ra-

dios and televisions.

Handling

To avoid breakage, do not apply excessive force to the switches or controls.

Care

If the exterior becomes dirty, wipe it with a clean, dry cloth. Do not use liquid clean-

ers such as benzene or thinner, or cleaning compounds or flammable polishes.

Keep this manual

After reading this manual, please keep it for later reference.

Keeping foreign matter out of your equipment

• Never set any container with liquid in it near this equipment. If liquid gets into

the equipment, it could cause a breakdown, fire, or electrical shock.

• Be careful not to let metal objects get into the equipment. If something does slip

into the equipment, unplug the AC adaptor from the wall outlet. Then contact

your nearest Korg dealer or the store where the equipment was purchased.

CE mark for European Harmonized Standards

CE mark which is attached to our company’s products of AC mains operated

apparatus until December 31, 1996 means it conforms to EMC Directive (89/

336/EEC) and CE mark Directive (93/68/EEC). And, CE mark which is attached

after January 1, 1997 means it conforms to EMC Directive (89/336/EEC), CE

mark Directive (93/68/EEC) and Low Voltage Directive (73/23/EEC).

Also, CE mark which is attached to our company’s products of Battery operated

apparatus means it conforms to EMC Directive (89/336/EEC) and CE mark Di-

rective (93/68/EEC).

THE FCC REGULATION WARNING (for U.S.A.)

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guar-

antee that interference will not occur in a particular installation. If this equip-

ment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Unauthorized changes or modification to this system can void the user’s au-

thority to operate this equipment.

Owner's Manual

Parts of the GT-120

[TUNING TYPE] dial

LCD display

Meter

[AUTO/MANUAL] switch

[SOUND] switch

[NOTE] switch

[FLAT] switch

Tuning guide

[CALIB] switch

INPUT jack

Built-in mic

OUTPUT jack

DC IN jack

(connect to AC adapter)

Power switch(STANDBY/ON/ )

Tuning procedure

The GT-120 has two tuning modes: (auto/manual) in whichMeter mode

you tune while watching a meter, and (manual) in whichSound mode

you tune to an audible reference tone.

■ Meter mode

1. If you are using an instrument with a pickup (such as an electric gui-

tar) or a mic, connect the instrument or mic to the INPUT jack of the

GT-120.

(If you connect the GT-120's OUTPUT jack to your amp etc., the sound

will be output thru the tuner. During your performance however, you

may want to turn the GT-120 power switch STANDBY to avoid noise.)

If a plug is inserted into the INPUT jack or OUTPUT jack, the built-in mic

cannot be used. Both jacks are mono. They cannot be used with stereo plugs.

If you wish to tune your instrument using the built-in mic, do not con-

nect a plug to the INPUT jack or OUTPUT jack. In steps 5 and 6, place

your instrument as close as possible to the built-in mic.

2. Turn the power switch to the ON or position. (At the position,

the power will be on, and in addition the display will be illuminated.)

When the power is turned on, the previously-selected reference pitch

(default setting: A=440 Hz) will be selected, and the GT-120 will be in

Meter mode (Auto)

3. If you wish to change the reference pitch (calibration), press the

[CALIB] switch.

Each time you press it, the reference pitch will rise 1 Hz. If you con-

tinue holding it, the pitch will rise continuously. The available range is

438 Hz–445 Hz.

4. Rotate the [TUNING TYPE] dial to select the appropriate instrument

or set to CHROMATIC.

Move the appropriate instrument name to the mark.

Each setting allows the following tuning. ( ): Default values for MANUAL

CHROMATIC

: C, C, D, E , E, F, F, G, G, A, B , B (A, sound output: A4)

GUITAR : 6E, 5A, 4D, 3G, 2B, 1E (6E)

OPEN D : 6D, 5A, 4D, 3F, 2A, 1D (6D)

OPEN E : 6E, 5B, 4E, 3G, 2B, 1E (6E)

OPEN G : 6D, 5G, 4D, 3G, 2B, 1D (6D)

OPEN A : 6E, 5A, 4E, 3A, 2C, 1E (6E)

DADGAD : 6D, 5A, 4D, 3G, 2A, 1D (6D)

BASS : LB, 4E, 3A, 2D, 1G, HC (LB) LB: Low B, HC: High C

5. Specify the note name.

When using AUTO

Play a single note on your instrument, and the name of the nearest note

will appear in the LCD display. Tune your instrument so that the cor-

rect note name is shown in the LCD display.

When using MANUAL

Press the [NOTE] switch until the note you wish to tune (C–B) appears

in the LCD display.

• Each time you press the [AUTO/MANUAL] switch, the setting will switch

between AUTO and MANUAL.

Thank you for purchasing

the Korg GT-120 guitar/

bass chromatic tuner. Be-

fore you use the GT-120,

please read this owner's

manual carefully, and use

the GT-120 as directed.

Keep this manual for fu-

ture reference.

JE F G 1

6. Play a single note on your instrument, and tune it so that the needle

of the meter is at the 0 position (center) and both indicators of the

tuning guide are lit.

While tuning, do not allow extraneous sounds to enter the mic.

Tuning is correct when the needle indicates the 0 position

(center) and both tuning guide indicators are lit.

AUTO : Meter mode (Auto)

MANUAL : Meter mode (manual)

SOUND : Sound mode (manual)

Reference pitch

(calibration)

Octave

(displayed only

for CHROMATIC)

Remaining

battery power

Flat tuning

String number

(not displayed

for CHROMATIC)

Note name

(C, C



, D, E



, E, F,



, G, G



, A, B



, B)

■ Sound mode

1. Make the settings described in steps 1–4 of "Meter mode."

2. Press the [SOUND] switch to enter Sound mode (manual).

3. Press the [NOTE] switch until the note to which you wish to tune

appears in the LCD display.

4. Listen to the pitch sounded by the GT-120, and tune your instrument

accordingly.

• To return to Meter mode, press the [AUTO/MANUAL] switch.

● Flat tuning

When the [TUNING TYPE] dial is set to GUITAR BASS or , you can use

Meter mode or Sound mode to tune to a pitch that is lowered by 1–4

semitones (  –  ) for the specified note.

1. As described in "Meter mode" or "Sound mode," make the note you

wish to flatten by 1–4 semitones appear in the LCD display.

Set the [TUNING TYPE] dial to either GUITAR or BASS. Flat tuning can

only be used for these selections.

2. Press the [FLAT] switch to select the number of semitones that you

wish to lower the selected note.

The LCD screen will indicate  –  (1–4 semitones).

3. Tune your instrument.

Replacing the batteries, and

the memory function

As the batteries begin to run down, accurate tuning will become more

difficult. Check the battery indicator in the LCD display, and replace the

batteries as soon as necessary.

The batteries are also used to preserve the memory when the power is

turned off, allowing the reference pitch, meter mode (manual), and the

note you selected for Sound mode to be remembered (Memory function).

When the batteries are removed or if they run down completely, the various

settings preserved by the memory function will be reset. (If an AC adapter

is connected to the GT-120 and plugged into an AC outlet, the settings will

not be reset.)

Even if you are using the GT-120 with an AC adapter, you should leave

the batteries installed.

2. Insert two AAA

batteries. Be careful to

observe the correct

polarity (+, -).

1. Press lightly and slide in the

direction of the arrow to open

the lid of the battery case.

3. Close the lid of the battery

case.

Adjustment screw

Adjusting the zero point of the meter needle

If the GT–120 is jarred while being transported etc., or due to normal ag-

ing after extended use, the VU style meter may drift away from the 0

position (center). Please re-adjust the VU style meter to the 0 position so

that tuning will be accurate.

1. While holding down the [AUTO/MANUAL] switch, turn the power

switch ON, and check whether the meter needle indicates the 0 posi-

tion.

2. If it does not indicate the 0 position, refer to the diagram in the above

section "Replacing the batteries, and the memory function," open the

battery cover, and use a small Philips (+) screwdriver (such as a

jeweler's screwdriver) to rotate the adjustment control so that the

needle indicates 0.

3. After making the adjustment (or if the meter needle indicated 0 in

step 1), press any one of the switches to return to normal operation,

and close the battery cover.

Specifications

Scale : 12 note equal temperament

Range : A0–C8

Reference tone : C2–C7 (5 octaves)

Tuning modes : Meter (auto/manual)

Sound (manual)

Flat tuning : 1–4 semitones (semitone steps)

Calibration range : A4=438–445 Hz (1 Hz steps)

Detection accuracy : +/-1 cent

Sound accuracy : +/-1.5 cents

Tuning guide range :Auto (chromatic)

-50 cents– -3 cents : 

-3 cents– +3 cents :  , 

+3 cents– +50 cents : 

Manual

-500 cents– -3 cents : 

-3 cents– +3 cents :  , 

+3 cents– +500 cents : 

Connectors : INPUT (1/4” mono), OUTPUT (1/4” mono),

DC IN (9V)

Power supply : AAA batteries x 2 (3V), or AC adapter ( )

Battery life : Approximately 100 hours (Alkaline batteries,

Meter mode, A4 continuous input)

Dimensions (WxDxH) : 74 x 120 x 36mm [2.91" x 4.71" x 1.42"]

Weight : 193g [6.8 oz] : including the battery

Included items : AAA batteries x 2 for checking operation

Options : )AC adapter (

(sold separately)

* Appearance and specifications are subject to change without notice.

Using the stand

By opening the stand located on the back, you can position the GT-120 at

a convenient angle.

The VU style meter may drift from the

0 position (center) when the OT–120

is tilted. If this occurs, perform the

procedure described in “Adjusting the

zero point of the VU style meter”

while the unit is tilted, so that the VU

style meter points to 0.

Specyfikacje produktu

Marka:	Korg
Kategoria:	Sprzęt DJ-ski
Model:	GT-120

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Korg GT-120, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Sprzęt DJ-ski Korg

Korg Rhythm Master Instrukcja

10 Grudnia 2024

Korg PuttRhythm Instrukcja

10 Grudnia 2024

Korg DT-10 Instrukcja

7 Października 2024

Korg OT-120 Instrukcja

27 Września 2024

Korg DTR-2000 Instrukcja

26 Września 2024

Korg CM-200 Instrukcja

23 Września 2024

Korg DTR-1000 Instrukcja

17 Września 2024

Korg A4501 Instrukcja

15 Września 2024

Korg Pitchclip Instrukcja

14 Września 2024

Korg AX1G Instrukcja

14 Września 2024

Instrukcje Sprzęt DJ-ski

Najnowsze instrukcje dla Sprzęt DJ-ski

Fuzzix MBR60 Instrukcja

14 Marca 2025

Line 6 Helix Control Instrukcja

11 Stycznia 2025

AlphaTheta DDJ-GRV6 Instrukcja

8 Stycznia 2025

Glorious Record Box 55 Instrukcja

4 Stycznia 2025

Glorious Record Box Display Door Instrukcja

4 Stycznia 2025

Glorious Session Cube XL Instrukcja

4 Stycznia 2025

Glorious Modular Mix Station Instrukcja

4 Stycznia 2025

Glorious Record Box Advanced 110 Instrukcja

4 Stycznia 2025

Glorious Mix Station 2 Instrukcja

4 Stycznia 2025

Glorious CD Box 90 Instrukcja

4 Stycznia 2025