Instrukcja obsługi Korg Ampworks Bass

Korg system hi-fi Ampworks Bass

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Korg Ampworks Bass (3 stron) w kategorii system hi-fi. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
Eas
y
Star
t
¾ REMS technology delivers an
array of classic Guitar/Bass
Amp, Speaker Cabinet and
Effect models
¾ Intuitive user interface with 3
Select Dials and 6 Knobs
¾ Loaded with 11 classic and
modern Guitar & Bass
Amplifiers
¾ 11 sought after Cabinet models
for Guitar and 10 Cabinet
models for Bass
¾ 9 Guitar Effect models
(Ampworks), 11 Bass Effect
models (Ampworks bass)
¾ 11 Preset Amp settings, 2 User
Programmable settings, plus
Manual setting
¾ Battery or AC powered
A
Am
mp
pw
wo
or
rk
ks
s
G
Gu
ui
it
ta
ar
r/
/B
Ba
as
ss
s
M
Ma
ai
in
n
F
Fe
ea
at
tu
ur
re
es
s
AAuuddiioo CCoonnnneeccttiioonnss::
1. If connecting headphones or powered monitors, select “LINE” on the LINE/AMP switch on the rear panel.
Select “AMP” if connecting to a guitar amplifier.
2. After making audio and AC connections, connect your guitar to the INPUT jack on the back panel. If using
headphones, connect to the OUTPUT jack on the back lower the VOLUME level and panel. On the top panel,
turn on the power by plugging the optional DC 4.5V adaptor into an AC outlet. The POWER LED will light and
the power will turn on.
3. If using batteries, the power will turn on when a mono cable is plugged into the INPUT jack.
4. Connect the OUTPUT jack to your mixer or guitar/bass amp.
5. When connections are complete, turn on the power of the mixer or amp and adjust the volume
appropriately.
Ampworks Guitar/Bass EasyStart
S
Se
el
le
ec
ct
ti
in
ng
g
a
an
nd
d
L
Li
is
st
te
en
ni
in
ng
g
t
to
o
A
Am
mp
pw
wo
or
rk
k’
’s
s
1
11
1
P
Pr
re
es
se
et
t
P
Pr
ro
og
gr
ra
am
ms
s:
:
1. Press the PRESET button on the front panel; the LED will light above the button.
2. Turn the AMP TYPE selector, an appropriate cabinet and effect will automatically be added to the amp model.
3. If you like, you can also try different cabinet and effect models with the amp models by simply turning the
selector knob.
L
Li
is
st
te
en
ni
in
ng
g
t
to
o
P
Pr
ro
og
gr
ra
am
ms
s-
-
P
PR
RO
OG
G1
1,
,
P
PR
RO
OG
G2
2,
,
a
an
nd
d
M
Ma
an
nu
ua
al
l:
:
1. Press the PROG/MANU button. Each time you press the button you will cycle through the following three
settings.
PROG1 (Green LED) User-writable program 1
PROG2 (Red LED) User-writable program 2
MANUAL (Orange LED) The current settings of the knobs and selectors
S
Sa
av
vi
in
ng
g
a
a
P
Pr
ro
og
gr
ra
am
m:
:
You’ve tweaked and turned some knobs and selectors, and you like the changes that you’ve made –
now to save your program: You can store two of your favorite settings in PROG1 and PROG2!!!
1. Press the WRITE button, the PROG/MANU button will blink.
2. Press the PROG/MANU button to select the writing destination. Each time you press the button, you will
alternate between a blinking PROG1 (Green LED) and PRO2 (Red LED).
3. Press the “WRITE” button to save your settings. If you decide not to save, press the CANCEL button.
R
Re
es
st
to
or
ri
in
ng
g
t
th
he
e
F
Fa
ac
ct
to
or
ry
y
P
Pr
re
es
se
et
t
P
Pr
ro
og
gr
ra
am
ms
s:
:
You can restore PROG1 and PROG2 to the factory settings as follows…
1. Hold down the “WRITE” button and turn on the power.
NOTE: Restoring the factory settings will over-write any changes you have made in PROG1/PROG2.
B
BY
YP
PA
AS
SS
S:
:
By bypassing Ampworks, your sound will be direct (dry) so there will be no amp types, cabinets, or
effects. When bypassed, the PRESET or PROG/MANU LED will be off.
1. To bypass Ampworks, hold down the PROG/MANU button for 2 seconds.
2. Press the PROG/MANU button once again to cancel bypass.
2
Ampworks Guitar/Bass EasyStart
3
U
Us
si
in
ng
g
a
an
n
o
op
pt
ti
io
on
na
al
l
f
fo
oo
ot
ts
sw
wi
it
tc
ch
h
t
to
o
c
co
on
nt
tr
ro
ol
l
A
Am
mp
pw
wo
or
rk
ks
s:
:
If the optional footswitch (PS100) is connected to the FOOTSW jack, you can perform a special
operation at power-on to specify whether the footswitch will change programs or turn bypass on/off.
1. To change programs, turn on the power without pressing any key. Pressing the footswitch will cycle in the
order of PROG1> PROG2> MANUAL> PROG1 etc….
2. To turn bypass on/off, turn on the power while holding down the PROG/MANU button.
Pressing the footswitch will turn bypass on/off.
N
No
oi
is
se
e
R
Re
ed
du
uc
ct
ti
io
on
n:
:
Ampworks for guitar and bass both feature programmable noise reduction.
To access noise reduction hold down the “TAP” button and turn the effect depth control left to right. After you
have made your setting, play a chord or single note and then stop.
Note: Noise that might have previously been present (due to high gain or single coil hum) should now be gone.
Make adjustments as necessary.
U
Us
si
in
ng
g
t
th
he
e
“
“T
Ta
ap
p”
”
b
bu
ut
tt
to
on
n:
:
The “Tap” button on Ampworks allows you to easily adjust certain effect parameters such as delay
time, modulation speed and reverb length.
To set the delay time, tap the “Tap” button to a desired tempo. Note: This is very useful for setting a delay
repeat in time with your song’s tempo.
To set the speed of a modulation effect and reverb length, use the same procedure.
Note: The Reverb length will depend upon the space between taps. (Maximum of 4 seconds)
Note: The above effects have different “proportion to tap intervals”. EX: Flanger = x2, Delay= x1,
Chorus/ Phaser/ Rotary= x2.
This means that if Flanger is selected (which has a proportion to tap interval of x2,) if you tap at a 4
second interval, Ampworks will set the parameter value (flanger speed) to twice that length, or 8 seconds.
You can also adjust the amount of effect level by turning the “Eff. depth” control.
Note: For more detailed information on Ampworks, please refer to the Owner’s Manual.

Specyfikacje produktu

Marka: Korg
Kategoria: system hi-fi
Model: Ampworks Bass

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Korg Ampworks Bass, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje system hi-fi Korg

Korg

Korg AX100G Instrukcja

7 Września 2024
Korg

Korg AW-2 Instrukcja

30 Sierpnia 2024
Korg

Korg Nu:Tekt HA-S Instrukcja

29 Sierpnia 2024
Korg

Korg DS-DAC-10R Instrukcja

27 Sierpnia 2024
Korg

Korg GA-40 Instrukcja

23 Sierpnia 2024
Korg

Korg DS-DAC-100 Instrukcja

22 Sierpnia 2024
Korg

Korg AX10G Instrukcja

21 Sierpnia 2024
Korg

Korg AudioGate 3 Instrukcja

21 Sierpnia 2024
Korg

Korg Soundlink DRS168RC Instrukcja

19 Sierpnia 2024
Korg

Korg AX10A Instrukcja

19 Sierpnia 2024

Instrukcje system hi-fi

Najnowsze instrukcje dla system hi-fi

Philips

Philips TAM3205M2 Instrukcja

14 Stycznia 2025
Philips

Philips TAM3505M2 Instrukcja

14 Stycznia 2025
OSD Audio

OSD Audio Nero Stream ARC Instrukcja

14 Stycznia 2025
Morel

Morel SUB-8X Instrukcja

14 Stycznia 2025
Morel

Morel BEAT-X Instrukcja

14 Stycznia 2025
Morel

Morel Sopran 634 Instrukcja

14 Stycznia 2025
Klipsch

Klipsch HD Theater 500 Instrukcja

14 Stycznia 2025
Lenco

Lenco MC-129 MP3 Instrukcja

13 Stycznia 2025
Terratec

Terratec HA-1 Charge Instrukcja

13 Stycznia 2025
Thomson

Thomson MIC400BT Instrukcja

12 Stycznia 2025