Instrukcja obsługi Konica Minolta Riva Zoom 75w

Konica Minolta Niesklasyfikowane Riva Zoom 75w

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Konica Minolta Riva Zoom 75w (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

Thank you for your purchase of a Minolta camera. This camera is

equipped with functions to suit all your photographic needs. Before

using your new camera, please take the time to read through this

instruction manual for it contains information important to the proper

use and care of your camera.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation. Changes or modications not

approved by the party responsible for compliance could void the user's authority to operate the

equipment. This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment o and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment

Regulations.

This mark on your camera certies that this camera meets the requirements of the EU

(European Union) concerning interference causing equipment regulations. CE stands for

Conformité Européenne (European Conformity).

NAMES OF PARTS

FRONT

1. Shutter-release button

2. Date buttons (DATE model only)

3. Data panel

4. Subject-program selector

5. Self-timer/Drive-mode button

6. Flash-mode button

7. Flash*

8. Back-cover release

9. Viewnder window*

10. Metering window*

11. Lens*

12. Self-timer/Remote-control lamp

14. Flash lamp (orange)

15. Focus lamp (green)

16. Viewnder*

17. ON/OFF button

18. Zoom control

19. Battery cover

20. Strap eyelet

21. Tripod socket

22. Rewind button

23. Film window

24. Back cover

BACK

DATA PANEL

1. Flash-mode indicator

2. Self-timer indicator

3. Continuous-drive indicator

4. Remote-control indicator

5. Date/Time display (date model only)

6. Low-battery symbol

7. Frame counter

8. Film-transport signals

9. Film-cartridge mark

10. Landscape/Night View mode

indicator

11. Night Portrait mode indicator

12. Close-up mode indicator

13. Subject-program pointer

1. Focus lamp (green)

Glows: Focus conrmed

Blinks: Subject too close

2. Flash lamp (orange)

Glows: Flash will re

Blinks quickly: Flash charging

Blinks slowly: Camera-shake warning

3. Focus frame

4. Close-framing guides

VIEWFINDER

Universal Copyright Convention

9222-2445-11 NI-C909 Printed in China

13. Autofocus windows/Remote-control receiver*

*Do not touch

EInstruction Manual

FOR PROPER AND SAFE USE

Read and understand all warnings and cautions before using this product.

WARNING

Batteries may become hot or explode due to improper use.

• Use only the batteries specied in this instruction manual.

• Do not install the batteries with the polarity (+/–) reversed.

• Do not subject batteries to re or high temperatures.

• Do not attempt to recharge, short, or disassemble.

• Tape over lithium battery contacts before disposal. Follow local codes

for battery disposal.

Use caution, accidents may occur when using this product near young

children.

Keep batteries or things that could be swallowed away from young

children. Contact a doctor immediately if an object is swallowed.

Immediately remove the batteries and discontinue use if...

• the camera is dropped or subjected to an impact in which the interior is

exposed.

• the product emits a strange smell, heat, or smoke.

The lens retracts when the camera is turned o or Auto Power O is

activated. Touching the lens barrel while it is retracting may cause injury.

Do not disassemble. Electric shock may occur if a high voltage circuit

inside the camera is touched. Take your camera to a Minolta Service

Facility when repairs are required.

TECHNICAL SPECIFICATIONS

Lens: 28-75mm f/3.5-8.9 power zoom lens with 4 elements in 4

groups

Focusing: 3-beam, active infrared autofocus system with focus lock;

Focusing range: 0.4m - (16 in. - ), Close-up: 0.4m - 1.0∞ ∞

(16 in. - 3.3 ft.); Maximum magnication 1/4.3X

Exposure: Center-weighted metering; Metering range (ISO 100):

28mm: EV 2.6 - 17, 75mm: EV 3.3 - 17; Film speed range:

Automatic setting for DX-coded lm ISO 25-3200 in 1EV

steps

Film transport: Auto advance to rst frame, auto rewind, auto threading,

manual start of rewind possible; continuous drive: 1.2

sec./frame (without ash)

Flash: Retractable, built-in ash, ashmatic with intensity control;

Recycling time: approx. 0.3 - 7 sec.; Range (ISO 100): 28mm:

0.4 - 5.9m (16 in.- 19.4 ft.), 75mm: 0.4 - 2.3m (16 in. - 7.5 ft.)

Viewnder: Real-image zoom; Diopter (subject at 3m/10 ft.): -1 diopter

Battery: One 3-volt CR123A or DL123A lithium battery; Battery

performance: Approx. 13 rolls (24 exp. roll w/ 50% ash)

Dimensions: 121 x 66.5 x 44mm (4-3/4 x 2-5/8x 1-3/4 in.)

Weight: 245g (8.64 oz.)

Specications are based on the latest information available at the time of printing

and are subject to change without notice.

OPERATING TEMPERATURE AND CONDITIONS

• This camera is designed for use for -10 to 40°C (14 to 104°F).

• At colder temperatures, the data panel response time will be slow; at

higher temperatures, the display will temporarily darken, but will

restore when the temperature normalizes.

• Never subject your camera to extreme humidity.

• To prevent condensation from forming, place the camera in a sealed

plastic bag when bringing it from the cold exterior to a warm building.

Allow it to come to room temperature before removing it from the bag.

• When photographing in cold weather, we recommend that you keep

the camera and spare batteries inside your coat to keep them warm

when you are not shooting. Cold batteries will regain some of their

charge when they warm up.

• This camera is not waterproof, dust-proof, or sand-proof; take care

when using it at the beach or near water. Costly or irreparable damage

may occur.

Minolta Co., Ltd. 3-13, 2-Chome, Azuchi-Machi, Chuo-Ku, Osaka 541-8556, Japan

Minolta GmbH Kurt-Fischer-Strasse 50, D-22923 Ahrensburg, Germany

Minolta France S.A. 365 Route de Saint-Germain, F-78420 Carrieres-Sur-Seine, France

Minolta (UK) Limited 7 Tanners Drive, Blakelands, Milton Keynes, MK14 5BU, England

Minolta Austria Ges. m.b.H. Amalienstrasse 59-61, A-1131 Wien, Austria

Minolta Camera Benelux B.V. Zonnebaan 39, P.O. Box 6000, NL-3600 HA Maarssen, The Netherlands

Belgium Branch Prins Boundewijnlaan 1, B-2550 Kontich, Belgium

Minolta (Schweiz) AG Riedstrasse 6, CH-8953 Dietikon, Switzerland

Minolta Svenska AB Albygatan 114, S-171 54 Solna, Sweden

Finland Branch Niittykatu 6 PL 37, SF-02201 Espoo, Finland

Minolta Portugal Limitada Av. do Brasil 33-A, P-1700 Lisboa, Portugal

Minolta Corporation

Head Office 101 Williams Drive, Ramsey, New Jersey 07446, U.S.A.

Los Angeles Branch 11150 Hope Street Cypress, CA 90630, U.S.A.

Minolta Canada Inc.

Head Office 369 Britannia Road East, Mississauga, Ontario L4Z 2H5, Canada

Vancouver Branch 230-3771 Jacombs Road, Richmond, B.C. V6V 2L9, Canada

Minolta Hong Kong Limited Room 208, 2/F, Eastern Center, 1065 King’s Road, Quarry Bay, Hong Kong

Minolta Singapore (Pte) Ltd. 10, Teban Gardens Crescent, Singapore 608923

Shanghai Minolta Optical

Products Co., Ltd. 368 Minolta Road, Songjiang, Shanghai, China

Step

Attach the strap as shown.

Your camera uses one 3-volt CR123A or DL123A lithium

battery to supply power for all camera operations.

➀Open the battery cover using a coin or

similar object.

➁Insert the battery according to the + and –

marks inside the battery chamber and snap

the cover closed.

• Before removing an old battery, make sure the camera

is o.

If the blinking low-battery symbol appears in the

data panel with the other indicators, you can still

use the camera, but the battery will have to be

replaced soon.

If the blinking low-battery symbol appears alone

(date model: only the date/time display with the

blinking low-battery symbol), you cannot use the

camera until you replace the battery. The shutter

cannot be released.

Use only 35mm, DX-coded film rated ISO 25 to

3200. ISO 400 or higher is recommended for taking

telephoto photographs or pictures in low light.

• Do not use Polaroid instant 35mm film. Winding

problems may occur.

➀Slide the back-cover release down to open

the back cover and place the lm cartridge

into the lm chamber.

• Always load and unload the film in subdued light.

➁Extend the lm tip to the “FILM TIP” mark,

making sure it lays at.

➂Close the back cover.

• The lm automatically advances to the rst frame and

appears in the data panel.

• If the lm has been loaded improperly, will blink in the

data panel and the shutter will remain locked. Open the

back cover and repeat the loading procedure.

➀Press the ON/OFF button to turn the

camera on.

• The ash will pop up and the lens barrel will extend.

• Press the ON/OFF button to turn the camera o.

• To conserve power, the camera automatically turns o if

it is not operated for more than eight minutes. The lens

barrel and ash will retract.

• Do not obstruct the lens while it is retracting.

FULL AUTO OPERATION - CONTINUED

➁Look through the viewnder and press the

W side of the zoom control to move toward

wide angle or the T side to move toward

telephoto.

• Do not hold the lens barrel; focus may not be accurate.

• Make sure your subject is at lease 0.4 m(16 in) from the

camera.

➂Align your subject within the focus frame

and press the shutter-release button

partway down.

➃When the green focus lamp glows, gently

press the shutter-release button all the way

down to take the picture.

• The ash will automatically re in low light.

• The lm automatically advances to the next frame.

Close-framing Guides

When your subject is closer than 1.2m (4 ft.) at

75mm, rst lock focus on your subject by pressing

the shutter-release button partway down, then

recompose your picture within the close-framing

guides.

• If the green focus lamp blinks, your subject is closer

than the minimum focusing distance of 0.4m (16 in.) and

will not be in focus. The shutter cannot be released.

• If the subject is very close to the camera, the green

focus lamp will glow, but the picture will not be in focus.

When your subject is located outside the focus

frame, you can rst lock focus on your subject, then

recompose the picture as desired.

➀Align the subject within the focus frame and

press the shutter-release button partway

down until the green focus lamp glows.

The lm will rewind automatically after the last

frame has been exposed.

When appears and blinks in the data panel,

open the back cover and remove the lm.

To begin rewind before the end of the roll, turn the

camera on and gently press the rewind button

using a pen or similar object.

LOW BATTERY SYMBOL

CLOSE-FRAMING

➁Without lifting your nger, recompose the

picture then press the shutter-release button

all the way down to take the picture.

FOCUS LOCK

MANUAL REWIND

If rewind stops before the lm has been completely rewound and all indicators

blink, DO NOT OPEN THE BACK COVER. Insert a fresh battery then press the

rewind button.

ATTACHING THE STRAP

INSERTING THE BATTERY

LOADING THE FILM

FULL AUTO OPERATION

REWINDING THE FILM

Autoash mode ( ), autoash with red-eye

reduction ( ), manual ll-ash ( ) or

ash cancel ( ) can be selected.

Press the ash-mode button until the desired

indicator appears in the data panel.

The sequence is as shown.

• When you turn the camera on, the built-in flash is set to

autoflash or autoflash with red-eye reduction, whichever

mode was last used.

The range of the built-in ash depends

on the lm speed and focal length you

are using. To ensure proper exposure,

make sure your subject is positioned

within the ash range.

• Do not hold the ash down; the shutter may not

release.

• For vertically framed pictures, hold the camera so the

ash is on top.

While pressing the shutter-release button partway down:

• The orange ash lamp will glow whenever the built-in

ash is on.

• When the orange ash lamp blinks slowly, your scene is

too dark for a sharp hand-held picture. Use ash or

place the camera on a tripod.

• When the orange ash lamp blinks rapidly, the ash is

charging. Wait until it glows steadily, then take the

picture. Flash recharge time is approximately 0.3 to 7

seconds.

In this flash mode, the flash will fire a few short

bursts before the main flash burst to reduce the

“red-eye” effect which occurs when photographing

people in low light.

Press the flash-mode button until appears

in the data panel, then take the picture.

• Before taking the picture, warn your subjects that the

ash will re a few short bursts before the picture is

taken.

• The orange ash lamp will blink indicating preash.

The ash will re with every shutter release

regardless of lighting. This can be used to reduce

harsh, unattering shadows on your subject’s face

or illuminate your subject when it is back-lit.

RED-EYE REDUCTION MODE

Press the ash-mode button until appears

in the data panel, then take the picture.

With ash-cancel, the ash will not re. This mode

should be used when photographing twilight

scenes or subjects that are beyond the ash

range.

Press the ash-mode button until appears

in the data panel, then take the picture.

• When the ash is cancelled, shutter speeds may be

slow. Placing your camera on a tripod is recommended.

MANUAL FILL-FLASH MODE

In autoflash mode,the flash will fire in low light.

AUTOFLASH MODE

FLASH CANCEL MODE

The self-timer delays release of the shutter for

approximately 10 seconds after the shutter-release

button is pressed.

➀Place the camera on a tripod and press the

self-timer/drive-mode button until

appears in the data panel.

➁Align your subject within the focus frame,

then press the shutter-release button.

• The self-timer indicator in the data panel and the self-

timer lamp will blink slowly during the countdown and

blink rapidly just before the shutter releases.

• Self-timer is automatically cancelled after the shutter is

released.

• To stop the self-timer, press the self-timer/drive-mode

button. Cancel the self-timer operation by turning the

camera o or pressing the self-timer button until

disappears from the data panel.

In this mode, the camera continuously takes

pictures and advances the lm as long as the

shutter-release button is held down.

➀Press the self-timer/drive-mode button until

appears in the data panel.

➁Press the shutter-release button down and

hold.

• Without ash, the shutter will release every 1.2

seconds; with ash, the shutter will release when the

ash is charged.

• Continuous-drive mode remains selected after you

nish the series.

• The subject-program mode remains selected as long as

you are pressing the shutter-release button. When you

have nished a series, the subject-program selection is

reset to auto.

The optional IR Remote Control RC-3 allows

remote camera operation up to 6 meters (19.7

feet) away.

• The remote control will not operate with backlit

subjects.

• Bright light or reections entering the viewnder may

aect the camera’s meter reading.

➀Press the self-timer/drive mode button until

appears in the data panel.

➁Point the remote control toward the front of

the camera and press either the Release or

Delay button.

• Release: The remote-control lamp on the camera blinks

once, then the picture is taken.

Delay: The remote-control lamp on the camera blinks

twice, then the picture is taken.

➀With the camera in remote mode, center the focus frame on the

subject, then press the shutter-release button partway down.

➁Recompose the picture, then use the remote control normally.

• Focus will remain locked after the picture is taken. To cancel focus hold, turn the camera off.

FLASH RANGE

• To cancel remote control mode, press the self-timer/drive mode button until

disappears or turn the camera o.

USING FOCUS HOLD IN REMOTE CONTROL MODE

The remote control uses a 3V lithium battery

(CR2032).

➀Pull out the battery chamber and remove

the old battery.

➁Insert a new battery into the chamber with

its + side up, then slide the chamber back

into the remote control.

CHANGING THE BATTERY

CONTINUOUS-DRIVE MODE

REMOTE CONTROL (SOLD SEPARATELY)

Emitter window

Delay button

Release button

Battery cover

FLASH LAMP

USING THE BUILT-IN FLASH SELF-TIMER

28mm

ISO 100

0.4-5.9m

16 in - 19.4 ft.

0.4-2.3m

16 in - 7.5 ft.

0.4-11.8m

16 in - 38.7 ft.

0.4-4.6m

16 in - 15.1 ft.

75mm

ISO 400

Specyfikacje produktu

Marka:	Konica Minolta
Kategoria:	Niesklasyfikowane
Model:	Riva Zoom 75w

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Konica Minolta Riva Zoom 75w, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Konica Minolta

Konica Minolta Dynax 700Si Instrukcja

23 Września 2024

Konica Minolta Dynax 9Xi Instrukcja

23 Września 2024

Konica Minolta Dynax 800Si Instrukcja

23 Września 2024

Konica Minolta Dynax 500Si Super Instrukcja

23 Września 2024

Konica Minolta Dynax 500Si Instrukcja

23 Września 2024

Konica Minolta Dynax 303Si Instrukcja

23 Września 2024

Konica Minolta Dynax 60 Instrukcja

23 Września 2024

Konica Minolta AF-Tele Super Instrukcja

23 Września 2024

Konica Minolta Auto S2 Instrukcja

23 Września 2024

Konica Minolta Dynax 300Si Instrukcja

23 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024