Instrukcja obsługi Klipsch RVX

Klipsch głośnik RVX

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Klipsch RVX (27 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/27

RVX

SPEAKER

OWNER'S MANUAL

REFERENCE SERIES

IMPORTANT SAFETY INSTRUCTIONS

1. READ these instructions.

2. KEEP these instructions.

3. HEED all warnings.

4. FOLLOW all instructions.

5. DO NOT use this apparatus near water.

6. CLEAN ONLY with dry cloth.

7. DO NOT block any ventilation openings. Install in accordance with the manufacturer's

instructions.

8. DO NOT install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including ampliﬁers) that produce heat.

9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug

has two blades with one wider than the other. A grounding type plug has two blades and a

third grounding prong. The wider blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult an electrician for replacement of the

obsolete outlet.

10. PROTECT the power cord from being walked on or pinched, particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. ONLY USE attachments/accessories specified by the manufacturer.

12. USE only with a cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold

with the apparatus. When a cart is used, use caution when moving the cart/apparatus

combina void injury from tip-overtion to a .

13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.

14. REFER all servicing to qualiﬁed service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has

been spilled or objects have fallen into the apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or has been dropped.

This symbol indicates that there are important operating and maintenance instructions

in the literature accompanying this unit.

This symbol indicates that dangerous voltage constituting a risk of electric shock is

present within this unit.

WARNING: To reduce the risk of fire or electrical shock, do not expose this apparatus to rain

or moisture.

WARNING: Voltages in this equipment are hazardous to life. No user-serviceable parts inside.

Refer all servicing to qualiﬁed service personnel.

CAUTION: Changes or modiﬁcations not expressly approved by the manufacturer could void the

user’s authority to operate this device.

ABOUT YOUR KLIPSCH PURCHASE

Thank you for your purchase of Klipsch speakers. After reading this manual and connecting your

system, you will hear the result of over 55 years of stringent engineering and class-leading

research and development. Like all Klipsch products, your speakers feature Klipsch Horn-loaded

Technology—the guiding design for the ﬁrst Klipschorn

®developed in 1946 and for every prod-

uct that has followed. Horn-loading allows your speakers to deliver high sensitivity, low distor-

tion, ﬂat frequency response and wide dispersion, which translates to unequaled power, detail

and dynamics, the hallmarks of “The Klipsch Sound.” Please be sure to ﬁll out the included

Warranty card or register online at www.klipsch.com so we are better able to serve you. Again,

thank you for choosing Klipsch and we hope that your speakers bring life to your music and

movies for many years.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

GRILLE

The speaker can be used with or without its grille in place. The grille attaches magnetically;

you can remove the grille easily by pulling it forward and replace it simply by lining up its

edges with the those of the speaker cabinet.

PLACEMENT

Your Reference RVX speakers are designed for maximum ﬂexibility and will perform well in a

wide variety of conﬁgurations. Figure 1 shows a typical home theater setup, with a center-

channel speaker (RVX-42) on top of a TV set, left and right front speakers (either RVX-42 or

RVX-54) ﬂanking the screen, another pair of speakers (RSX-4 or RSX-5) to the sides of the lis-

tening area for the main surrounds, and a third pair behind for the surround back channel in a

7.1-channel (Dolby Digital EX or DTS-ES) system. Below are speciﬁc placement recommenda-

tions for each function.

Center-Channel Speaker: Center the speaker directly above or below your video screen. The

integral stand allows the speaker to be placed on top of the TV (or on a shelf just above or

below it) or mounted on the wall (see wall mounting instructions). Ideally, the speaker’s front

baﬄe should be ﬂush with the front of the screen. See stand adjustment section for more

detail.

Front Left and Right Speakers: The front left and right speakers should be approximately in

line with your video screen and equidistant from it. The distance from the screen is not critical,

though wide separation will tend to make the sound more spacious. Avoid having either

speaker closer than 2 feet to a side wall, and if they are on shelves or in a cabinet, place them

so that their fronts are at least ﬂush with the cabinet’s front. Place them at seated ear height if

that is practical.

Left and Right Surround Speakers: Your RVX speakers have been designed to acoustically

and cosmetically match the Klipsch Reference Satellite family of speakers. Please see your

authorized Klipsch dealer to see which Reference Satellite model is right for you.

The best location for speakers employed as surround speakers is on or against the walls to the

sides of the seating area, anywhere from adjacent to the listening position to about 20 degrees

behind it. Mount them above the ear height of seated listeners (5’-7’ high) but avoid placing

them up against the ceiling. Aim them straight across the room or back slightly toward the rear

wall for a more diﬀuse sound or toward the listening position for a more direct sound. The

design of the Reference Satellite models allows great ﬂexibility, however, and good results can

be achieved with configurations that depart significantly from the ideal.

6'-15'

FLAT

PANEL

X Z

Optional

sub

Optional

sub

X=Y=Z

7.1 or Alternative 5.1

7.1 or Alternative 5.1 6.1

Figure 1

ENGLISH

BUT FIRST: TYPES OF CONNECTORS

Bare wire — Pull the two conductors apart for about an inch and strip approximately

1/4”

insulation from the end of each. (A wire stripper will simplify this, but you can use an ordinary

pocket knife to cut around and through the insulation down to the wire.) Twist the strands of wire on

each individual conductor tightly together. Loosen the nuts on a pair of binding posts until the holes

through the metal posts are exposed, then insert the bare wire through the holes. Screw the nuts

down finger-tight on the wire. Make sure that no strands of wire are touching from one binding post

to the other or to any strands from the other conductor. Failure to observe this precaution at either

end of the connection can result in amplifier malfunction or damage.

Pins — Many pre-made speaker cables are terminated with metal pins. Loosen the nuts on a

pair of binding posts until the holes through the metal posts are exposed, then insert the pins

through the holes. Screw the nuts down ﬁnger-tight on the pins — do not over-tighten. Make

sure that there is no metal-to-metal contact between the two pins or binding posts. Failure to

observe this precaution at either end of the connection can result in ampliﬁer malfunction or

damage.

Spade lugs — Some speaker cables are terminated with U-shaped connectors called spade

lugs. Loosen the nuts on a pair of binding posts and slip the spade lugs around the metal posts.

Screw the nuts down ﬁnger-tight on the lugs and inspect to ensure they have remained ﬁrmly

in place. Make sure that there is no metal-to-metal contact between the two lugs or binding

posts. Failure to observe this precaution at either end of the connection can result in ampliﬁer

malfunction or damage.

OTHER TYPES OF SPECIALTY CONNECTORS ARE AVAILABLE TO FACILITATE HOOKING UP YOUR

SPEAKERS. PLEASE CONSULT YOUR AUTHORIZED KLIPSCH DEALER FOR SUGGESTIONS AND

FURTHER DETAILS.

SPEAKERS TO AMPLIFIER: KEEPING IT STRAIGHT

One of the most important things about hooking up your speakers is keeping them in the

same polarity, or phase. If they are connected out of phase, bass and sound localization will

be degraded.

The easiest way to ensure that your speakers are wired in phase is to always connect the

positive and negative output terminals on your ampliﬁer or receiver to the matching input

terminals on your speakers: positive ("+", color-coded red) to positive and negative ("–", color-

coded black) to negative. (See Figure 3).

Most pre-terminated speaker cables have color-coded connectors that make it easy to match

output and inputs correctly. If yours do not, or if you are making your own out of paired,

two-conductor wire, look for identifying marks on the insulation of the two conductors.

Normally there will be printing, a stripe or a molded ridge along one of the conductors.

Surround Back Speakers: If your electronics support Dolby Digital EX, THX Surround EX, or DTS-

ES 7.1 or 6.1-channel surround, you can place one or two speakers behind the seating area to

serve as surround back speakers. As with the left and right surrounds, the optimum location is

above seated ear level. If you are using just one back surround speaker, it should be centered

behind the listening area; if you are using two, they should be spaced fairly close together. With

this type of system, the regular left and right surrounds should be located adjacent to the seating

area rather than behind it.

STAND ADJUSTMENT AND WALL MOUNTING

The RVX-42’s attach to their stands via a bolt that allows them to be used in either the vertical ori-

entation as they are shipped for shelf top use or horizontally, as is typical for center channel use.

To adjust the base, remove the stand bolt tool from the rear of the unit and remove the bolt from

the stand. Reposition the stand in the center mounting point and then replace the stand bolt tool

in the opening that the stand bolt was previously installed within. (See Figure 2).

You may also use an optional wall or ceiling mount that will fit the provided 3/8" – 16 inserts.

Please see your authorized Klipsch dealer to determine which model is right for you.

To install the RVX-42, ollow the instructions below:f

Locate the included wall mount template with bubble level and position on the wall in the desired

location.

Mark the screw locations for the model you are installing.

Screw #8 pan head wood screws (at least two inches in length) into a wood stud or dry wall

anchors with the appropriate load rating. Leave the screw heads protruding from the wall surface

approximately 1/4” and adjust as needed when hanging the speaker.

Attach the supplied self-stick rubber pads to the rear of the speaker.

Connect the speaker wire to the speakers binding posts. See “Speaker to Amplifier: Keeping it

Flip the switch at the top of the rear of the speaker to “On Wall” for accurate bass response.

Hook the speaker keyholes on the screw heads protruding from the wall. Adjust the height of

the screw heads for a snug fit. Do not over-tighten.

Fine tune the speaker’s angle if using an optional wall mount that fits the provided 3/8" – 16 inserts.

CONNECTIONS

Note: Proper connection of your speakers to your amplifier or receiver is vital to obtaining good sound

quality. Please follow these directions carefully. Sloppy connections can cause amplifier malfunction

or damage.

Klipsch Reference Series speakers are wired internally with multiple gauges of high-purity copper

wire, carefully selected and wound to ensure optimum signal transfer at all frequencies. You will obtain

best performance from your speakers if you connect them to your amplifier or receiver with similar

quality wire available from your dealer. We recommend that you use 18-gauge or heavier (lower-

gauge) stranded copper wire. Use a lower gauge (heavier) wire for longer runs to reduce the amount

of amplifier power lost due to the wire’s resistance.

Figure 2

Figure 3

ENGLISH

straight

Specyfikacje produktu

Marka:	Klipsch
Kategoria:	głośnik
Model:	RVX

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Klipsch RVX, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje głośnik Klipsch

Klipsch Reference RB-25 Instrukcja

15 Stycznia 2025

Klipsch Reference RB-35 Instrukcja

15 Stycznia 2025

Klipsch PIC-525-T-SC Instrukcja

15 Stycznia 2025

Klipsch KI-102-SMA-II Instrukcja

15 Stycznia 2025

Klipsch PIC-450-T Instrukcja

14 Stycznia 2025

Klipsch Synergy C-2 Instrukcja

14 Stycznia 2025

Klipsch Synergy F-2 Instrukcja

14 Stycznia 2025

Klipsch Synergy F-3 Instrukcja

14 Stycznia 2025

Klipsch Synergy C-3 Instrukcja

14 Stycznia 2025

Klipsch PIC-525-T Instrukcja

14 Stycznia 2025

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Bowers & Wilkins LCR3 Instrukcja

15 Stycznia 2025

Hifonics Vulcan VX6.2E Instrukcja

15 Stycznia 2025

Pyle PLRGSW64BK Instrukcja

15 Stycznia 2025

ION Insta Sound Instrukcja

15 Stycznia 2025

Pure Acoustics QBT-340 Instrukcja

15 Stycznia 2025

Yamaha WX-010 Instrukcja

15 Stycznia 2025

Polk REACT SOUND BAR 1 Instrukcja

15 Stycznia 2025

Sennheiser AMBEO Soundbar Plus SB02M Instrukcja

15 Stycznia 2025

Power Dynamics PDW5W Instrukcja

15 Stycznia 2025

Edifier M1250 Instrukcja

14 Stycznia 2025