Instrukcja obsługi Klipsch KHC-6

Klipsch głośnik KHC-6

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Klipsch KHC-6 (6 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
KLIPSCH
HOME
SERIES A R C H I T E C T U R A L L O U D S P E A K E R S
O w n e r ’ s M a n u a l a n d W a r r a n t y
SYNERGY HOME SERIES
KHW-5 & KHC-6 Owner’s Manual
I M P O R U C T I O N STANT SAFET Y INST R
1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all instructions.
5. DO NOT use this apparatus near water.
6. CLEAN ONLY with dry cloth.
7. DO NOT block any ventilation openings. Install in accordance with the manufacturer's instructions.
8. DO NOT install near any heat sources such as radia heat registers, or othertors, stoves,
a t.pparatus (including amplifiers) that produce hea
9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wider blade or the third prong are provided for your safety If the provided plug does not fit.
into your outlet, consult an electrician for replacement of the obsolete outlet.
10. PROTECT the power cord from being walked on or pinched, t plugs, particularly a convenience
receptacles, and the point where they exit from the apparatus.
11. ONLY USE attachments/accessories specified by the manufacturer.
12. USE only with a cart, or table specified by the manufacturerstand, tripod, bracket, , or sold with the
apparatus. voidWhen a cart is used, use caution when moving the cart/apparatus combination to a
injury from tip-over.
13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.
14. SerREFER all servicing to qualified service personnel. vicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, pparatus has been exposed to rain or moisture, the a does
not operate normally, or has been dropped.
This symbol indicates that there are important operating and maintenance instructions in the
literature accompanying this unit.
This symbol indicates that dangerous voltage constituting a risk of electric shock is present
within this unit.
WARNING: oltaRisk of Electrical Shock. Do Not Open. V ges in this equipment are hazardous to life.
No user-serviceable parts inside. Refer all servicing to qualified service personnel.
WARNING: To reduce the risk of fire or electrical shock, do not expose this apparatus to rain or moisture
Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids –
such as a vase of flowers – are placed on the apparatus.
WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance
with the installation instructions.
No naked flame sources – such as candles – should be placed on the product.
Caution: Changes or modifications not expressl pproved by the manufacturer could void the user’y a s
authority to operate this device
Your new Klipsch architectural speakers have been designed to deliver g t sound while remainrea -
ing unobtrusive wherever you install them. For optimum performance, use the KHW-5 model as
front, -center or surround channels in audio or home theater applica or as part of a distribtions,
uted sound system. Use the KHC-6 model for distributed sound in kitchens, hallways or bath
rooms. They are also suitable for use as surround channels.
K H W -5 SP EAKER PLACE MENT
Designed to function in any standard wall, ceiling or drop ceiling, Klipsch in-wall speakers are
engineered for years of performance. Minimum construction requirements call for drywall or other
mounting surfaces to be at least
3/8" thick.
When planning speaker placement, maximum performance is realized when speakers are placed
at equal distance from the listener and along a common wall. This helps ensure the best stereo
effect. For non-critical listening environments (or when the listening position ma y widely)y var
speaker placement may be wherever is most convenient, although in these cases stereo imaging
may be lost. If this option is used, Klipsch recommends using the "mono" setting on the system’s
preamplifier.
K H W T I O N-5 SP EAKER INSTA L L A
Contents Description Quantity
Speaker Modules 2
Frames 2
Grilles 2
Screws (#6 x 11/ ) -5)24 (KHW
Tools Required
#2 Phillips Screwdriver
Hole Saw
New Construction
1. ralInsert the frame into the wall opening and attach via the swinging "dog" connectors integ
with the frame.
2. At this point, you may paint the wall and frame together. You may also want to paint the
speaker grilles. Klipsch in-wall frames and grilles are designed to accept most types of paint.
Care should be taken to avoid excessive paint build-up in the grille perforations.
3. Install the module with the screws provided and press the grille in place.
Existing Construction
1. Cut the appropriate size opening in the wall using the template provided. Cutout dimensions
are provided in the "Specification" section at the back of this manual. Sizes are minimum. If
accuracy of cut (straightness/squareness) cannot be achieved, you may add
1/4" to each
dimension. Be careful not to cut through any existing wiring or plumbing. void compromisingA
any fire stops between studs.
Included in Speaker Module Carton Included in
Rough-in Kit Carton
Template Grille Baffle Frame Bracket
2. Run wiring to the wall opening(s). Be sure to comply with any codes that may apply in your
area.
3. (a) If you want to paint the decorative frame and the wall together, insert the frame and attach
with the dogs. DO NOT OVERTIGHTEN.
(b) If you will not be re-painting, you may immediately install the frame and speaker assembly.
The frame’s mounting dogs will "sandwich" the wall and frame together. The module is
installed with the screws and the grille is pressed into place.
K H W-5 OPERATING CONTROLS
Tweeter Switch
If installing in an acoustically bright room, such as some bathrooms and kitchens, you may want
to adjust the tweeter level located on the front baffle. The position of this switch should always be
checked prior to speaker module installation.
Infrared Sensor Mount
The KHW-5 features a 1/ ” f2infrared sensor locator on the baf le. The location of the knock-out is
shown below.
KHC-6 SPEAKER PLACEMENT
Designed to function in any ceiling or drop ceiling, Klipsch in-ceiling speakers are engineered for
years of performance. Minimum construction requirements call for drywall or other mounting sur-
faces to be at least 3/ -8" thick. In drop ceiling installations, typical "drop in" 2’ x 4’ and 1’ x 1’ ceil
ing tiles are composed of low density materials which can (a) visibly sag over time due to the
weight of the speaker and (b) vibrate audibly, . detracting from the overall sound quality Klipsch
recommends that in order to maximize the acoustic performance of your KHC-6 speakers you
replace the original mounting panel with 1/2" to 3/4" plywood or medium density fiberboard (MDF).
IC SPEAKER INSTA L L AT I O N
Contents Description Quantity
Speaker Modules 2
Grilles 2
Tools Required
#2 Phillips Screwdriver
Hole saw
1. Cut the appropriate diameter circle using the hole template provided. Cutout dimensions are
provided in the "Specification" section at the back of this manual. Sizes are minimum. If
accuracy of cut (a perfect circle) cannot be achieved, you may add up to
1/ Be4" to the radius.
careful not to cut through any existing wiring or plumbing. Avoid compromising any fire stops
between studs.
2. Run wiring to the ceiling opening(s). Be sure to comply with any codes that may apply in your
area.
3. ,(a) If you want to paint the decorative frame and the ceiling together insert the speaker
assembly and attach with the dogs. DO NOT OVERTIGHTEN. Install the paint mask in place of
the grille and paint.
(b) If you won’t be re-painting, you may immediately install the speaker assembly. The frame’s
mounting dogs will "sandwich" the ceiling and frame together. The module is installed with the
screws and the grille is pressed in place.
KHC-6 OPERATING CONT ROLS
Tweeter Switch
If installing in an acoustically bright room, such as some bathrooms and kitchens, you may want
to adjust the tweeter level located on the front baffle. The position of this switch should always be
checked prior to speaker module installation.
Swivel Horn Tweeter
The Klipsch KHC-6 features a swivel tweeter to aim high frequency sound. To aim sound directly
at the listening area, simply remove the grille, and gently adjust the horn to the desired angle.
DO NOT ATTEMPT TO TURN THE TWEETER STEM WHILE ADJUSTING THE SWIVEL TWEETER.
ARCHITECTURAL SPEAKERS

Specyfikacje produktu

Marka: Klipsch
Kategoria: głośnik
Model: KHC-6

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Klipsch KHC-6, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Klipsch

Klipsch

Klipsch R50-PM Instrukcja

8 Października 2024
Klipsch

Klipsch Flexus Core 100 Instrukcja

5 Października 2024
Klipsch

Klipsch Flexus Sub 100 Instrukcja

5 Października 2024
Klipsch

Klipsch Flexus Core 200 Instrukcja

5 Października 2024
Klipsch

Klipsch R-50M Instrukcja

5 Października 2024
Klipsch

Klipsch Palladium P-38F Instrukcja

5 Października 2024
Klipsch

Klipsch PRO-800SW Instrukcja

4 Października 2024
Klipsch

Klipsch DS-160CDT Instrukcja

4 Października 2024
Klipsch

Klipsch DS-160C Instrukcja

4 Października 2024
Klipsch

Klipsch THX-6000-LCR-L Instrukcja

4 Października 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel

Teufel Rockster Air Instrukcja

15 Października 2024
Alpine

Alpine PSS-22WRA Instrukcja

15 Października 2024
Bauhn

Bauhn APPS-0724 Instrukcja

15 Października 2024
Aiwa

Aiwa SP-A100 Instrukcja

15 Października 2024
Harman Kardon

Harman Kardon Citation One Instrukcja

14 Października 2024
Alpine

Alpine 30MC Instrukcja

14 Października 2024
Magnat

Magnat Needle 9000 ALU Instrukcja

14 Października 2024
Pioneer

Pioneer SP-T22A-LR Instrukcja

14 Października 2024
Sharp

Sharp PS-932 Instrukcja

14 Października 2024
Pyle

Pyle PDWR64BTW Instrukcja

13 Października 2024