Instrukcja obsługi Klipsch IC-400-T

Klipsch głośnik IC-400-T

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Klipsch IC-400-T (6 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
I N - C E I L I N G L O U D S P E A K E R S
O ’ MW N E R S A N U A L A N D WA R R A N T Y
I C - 4 0 0 - T , I C - 5 2 5 - T & I C - 6 5 0 - T
3. To install the tilebridge, fold the rail side of the ring back
upon itself using the spring tensioner on the reinforcement ring
to allow insertion into the cutout hole. Once it is inserted into
the cutout hole, release the reinforcement ring such that it
unfolds back to its normal position. Position tilebridge over
cutout hole, and insure that the tile rails rest on the t-grid struts.
4. The wiring compartment is intended as a termination point
for the audio circuit. Access to this compartment is gained by
removing the terminal cover located on the back of the
speaker. The terminal cover will accept the appropriate
conduit/wire adapter (provided). Feed wires through
conduit/wire adapter and connect to the input terminal
according to the desired operation mode. Be sure to observe
proper polarity. Replace the terminal cover and tighten the
conduit/wire adapter to secure the wire.
Caution: When connecting 70V or 100V distributed
line systems, take care to ensure proper terminal
connection. Connection to the low impedance termi-
nal could result in speaker damage, amplifier
damage, or both.
Thank you for purchasi ng your Klipsch IC-400-T,
IC-525-T or IC-650-T in-ceiling speakers.
The IC-400-T, IC-525-T and IC-650-T in-ceiling speakers have been
designed for music reinforcement applications. Unobtrusive,
these loudspeakers are engineered for easy, versatile installation.
The IC-400-T, IC-525-T and IC-650-T feature an internal transformer
for 70V/100V distributed-line systems. The transformer taps are
selected using a rotary switch located conveniently under the
grille. For applications where 8 ohm operation is required, the
transformer can be by-passed by using an optional connection
located on the back input terminal and selectin 8 Ohm on the
front switch.
Before installing your speakers take a moment to check the
contents of the cartons and make sure nothing has been
damaged in transit.
Contents Description QUANTIT Y
Speaker Modules 2
Grille 2
Reinforcement Ring 2
Rails 4
Cardboard Cutout Template and Paint Mask 2
Screws (Attach Rails to Reinforcement Ring) 8
3/4" Adapter Fittings 2
Installation Guidelines
The IC-400-T, IC-525-T and IC-650-T include a tilebridge for use
when installing the loudspeaker into suspended ceilings or wher-
ever additional reinforcement of the ceiling material is required.
The tilebridge and loudspeaker are designed such that installa-
tion may be accomplished where access above the ceiling is
not possible or may be difficult.
Installation
1. The tilebridge is composed of three parts—a reinforcement ring
and two rails. The two rails should be attached to the reinforce-
ment ring using the four included screws as shown below.
Caution: Be sure to comply with any and all building codes
in your area.
2. To install your IC-400-T, IC-525-T or IC-650-T cut out a hole in the
ceiling using either the cardboard cutout template provided with
your speakers or consult the measurements below. Pull wiring
through hole.
I C - 4 0 0 - T , I C - 5 2 5 - T & I C - 6 5 0 - T
I C - 4 0 0 - T , I C - 5 2 5 - T 9.125 " R o u n d
I C - 6 5 0 - T " R o u n d10.125
5. Insert the speaker into the cutout hole. With a #2 Phillips screw-
driver, tighten the four dog clamps until they are seated securely
against the ceiling surface. Do not overtighten.
6. For installations using 70v/100v input connection, set the switch
on the front panel to the desired setting. For applications where 8
Ohm impedance is desired, the switch should be set to 8 Ohms.
Note: The speaker comes from the factory set at the lowest
output setting (highest impedance).
7. Using the flat of your hand, insert grille into speaker frame
making sure it is securely seated and flush.
Se i s m i c Tab
A seismic tab, located on the back of the speaker, is used
as a secondary security point. Some construction codes may
require its use. To utilize the seismic tab, run a support wire
from a secure point in the ceiling and attach it to the tab.
Be sure to consult the construction codes in your area.
Klipsch recommends the use of this tab in all installations as
a secondary means of support.
15W
7.5W
15W
1.875W
3.75W
3.75W
7.5W
70V
100V
IC-400-T tap selectable
30W
7.5W
15W
30W
3.75W
7.5W
15W
70V
100V
IC-525-T tap selectable
60W
60W
15W
30W
7.5W
15W
30W
70V
100V
IC-650-T tap selectable

Specyfikacje produktu

Marka: Klipsch
Kategoria: głośnik
Model: IC-400-T

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Klipsch IC-400-T, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Klipsch

Klipsch

Klipsch R50-PM Instrukcja

8 Października 2024
Klipsch

Klipsch Flexus Core 100 Instrukcja

5 Października 2024
Klipsch

Klipsch Flexus Sub 100 Instrukcja

5 Października 2024
Klipsch

Klipsch Flexus Core 200 Instrukcja

5 Października 2024
Klipsch

Klipsch R-50M Instrukcja

5 Października 2024
Klipsch

Klipsch Palladium P-38F Instrukcja

5 Października 2024
Klipsch

Klipsch PRO-800SW Instrukcja

4 Października 2024
Klipsch

Klipsch DS-160CDT Instrukcja

4 Października 2024
Klipsch

Klipsch DS-160C Instrukcja

4 Października 2024
Klipsch

Klipsch THX-6000-LCR-L Instrukcja

4 Października 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel

Teufel Rockster Air Instrukcja

15 Października 2024
Alpine

Alpine PSS-22WRA Instrukcja

15 Października 2024
Bauhn

Bauhn APPS-0724 Instrukcja

15 Października 2024
Aiwa

Aiwa SP-A100 Instrukcja

15 Października 2024
Harman Kardon

Harman Kardon Citation One Instrukcja

14 Października 2024
Alpine

Alpine 30MC Instrukcja

14 Października 2024
Magnat

Magnat Needle 9000 ALU Instrukcja

14 Października 2024
Pioneer

Pioneer SP-T22A-LR Instrukcja

14 Października 2024
Sharp

Sharp PS-932 Instrukcja

14 Października 2024
Pyle

Pyle PDWR64BTW Instrukcja

13 Października 2024