Instrukcja obsługi King WSC1215-T-B

King Podgrzewacz WSC1215-T-B

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla King WSC1215-T-B (4 stron) w kategorii Podgrzewacz. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

1. ad a instructions b ore wiring or using thisRe ll ef

heater.

2. WARNING: This heater is hot wh in use. Toen

avoid burns, do not let bare skin touch hot sur-

faces. Keep combustible materials, such as furni-

ture, pillows, bedding, paper clothes, boxes,s,

etc., and curtains at least 3ft (.9 m) from the

front of the heater and keep them away from the

sides and rear.

3. CAUTION: Extreme caut n is necessary when anyio

heater is used by or near children or in lids andva

whenever the heater is left operating and at-un

tended.

4. Do not operate any heater after it malfunctions.

D co ect power at service panel and h eis nn av

heater inspected by qualied electrician for re-

pair before reusing.

5. Do not use outdoors.

6. WARNING: To disconnect heater,

turn controls to OF and turnF,

OFF power to heater circuit at

IMPORTANT INSTRUCTIONS

ELECTRIC S CK OR FIRE HAZARDHO

DANGER

WARNING

! !

Re efad Car ully - These instructions are written in an eort to prevent potential diculties that m ht arise during ig

insta at n. Studying the instructions rst may s e you considerable time and money later. Observing the fo owing ll io av ll

procedures will keep inst lat n time to a minimum. . al io Save these instructions for future use

Covers a W Se s models ll rie

W Fan Force Electric

Space Heater

King Electrical Mfg. Co. 9 th Ave So. Seattle, WA 9 206- 2- 00 www.king-electric.com 131 10 8108 76 04

IMPORTANT INSTRUCTIONS

When usin electrical heatin a liances asic precautio should always e ollowed to g g pp , b ns b f

reduce he risk of re, electric shock and injury to perso includin the ollowing: t ns, g f

main disconnect panel.

7. WARNING: Do not insert or allow foreign objects

to enter any ventilation or exhaust opening as this

may cause an electric shock, re, or damage to

the heater.

8. To prevent a possible of re, do not block air in-

takes or exhaust in any manner.

9. A heater has hot and arching or sparking parts

inside. Do not use it in areas where gasoline,

paint, or ammable vapors or liquids are used or

stored.

10. WARNING: Use this heater only as described in this

manual. Any other use is not recommended by the

manufacturer and may cause re, electric shock,

explosion or injury to people and or property.

SAVE T SE INSTRUCTIONS HE

Figure 1

Figure 2

ELECTRIC SHOCK OR FIRE HAZARD

! !

Figure 3

W INSTALLATION INSTRUCTIONS

CAUTION!

Turn OFF all electrical power

to install heater

Rating Label Location

Total Amps Minimum AWG. Wire

Size (Copper Circuit Breaker or

Fuse Size

0 thru 12 15 amp #14

12.1 thru 16 20 amp #12

16.1 thru 24 30 amp #10

Minimum Clearances for heater: Table 1

Front TOP BOTTOM SIDES

36 in 12 in 4 in 6 in

0.9 m 30.5 cm 10.2 cm 15.2 cm

Selecting A Location For Your Heater:

DO NOT install less than 6” (15cm) from vertical side

walls or open edge of door. This heater must have an

unrestricted airflow. DO NOT select a location where it

is likely to be blocked by furniture, curtains, etc. Be

sure the location selected allows sufficient space for the

heater as shown by Table 1. DO NOT locate this heater

in an area where combustible vapors, gases liquids, or

excessive lint, dust or moisture is present.

The wire and breaker sizing chart will give a general rule

of installation size. Consult an electrician if you are not

knowledgeable about wiring codes.

Wire and Breaker Sizing: Table 2

WIRING: Branch Circuit Connection

1. Connect heater only to the voltage, amperage and

frequency specified on the nameplate.

2. Wiring procedures and connections shall be in accor-

dance with all National and local codes having juris-

diction.

3. Set the bag containing the grille and packet with

two (2) grille screws aside.

4. Loosen mounting screw and remove fan heater as-

sembly.

5. A knockout of 1/2 inch conduit size (7/8 inch /

2.2cm) is provided in the back and side of the heater

for power to enter. Provide proper strain relief con-

nectors for your wire entering the wallbox.

6. Install wallbox a minimum of 6” from vertical side-

walls and 4” above floor. The front edge of wall

can MUST extend 1/2” beyond finished wall sur-

face.

7. Secure wallbox to the 2 x 4 studs using the two (2)

holes on the side of the wallbox. Secure to wall stud

on opposite side if required.

8. Connect supply wires, attach ground feed wire to

the green ground wire with wire nuts.

9. Reinstall heater assembly into wallbox with screw at

top of interior.

10. Install grille securely with screws provided in

packet. Do not over tighten.

11. Test unit by turning thermostat up past room tem-

perature. You will see a puff of smoke as the ele-

ments are energized and the fan turns on. This is a

normal burn off of manufacturing lubricants and will

dissipate in 5 minutes.

12. Heater will continue to run until the room tempera-

ture you set is reached and then turn itself off until

the temperature drops again.

CAUTION - High temperature. Risk of fire , keep electri-

cal cords, drapery, furnishings, and other combusti-

bles at least 3 feet (0.9 m) from the front of the

heater as well as away from the side and rear. To

reduce the risk of fire, do not store or use gasoline or

other flammable vapors and liquids in the vicinity of the

heater.

Figure 2

Wiring Diagram Figure 5

Zero clearance to insulation.

Figure 4

DANGER

Table 3

This heater is equipped with a thermal overload

Smart Limit Protection which disconnects ele-

ments and motor in the event normal operating

temperatures are exceeded. If thermal overload trips

due to abnormal operating temperatures, thermal over-

load shall remain open until manually reset by turning

the heater OFF for fifteen minutes. Inspect for any ob-

jects on or adjacent to the heater that may cause high

temperatures. After inspecting the heater, keep the

power to the heater off for 10 minutes to reset the SLP

thermal protector. If the SLP thermal protector shuts

the heater off again, immediately turn the heater OFF

at the circuit breaker and inspect the heater for possible

fan motor failure or dirt and lint on the heating ele-

ment. Repeat the starting procedure. DO NOT TAMPER

OR REMOVE THIS THIS DEVICE.

General information and Guidelines:

This heater must be properly installed before it is used.

DO NOT tamper with or change the operating of this

heater. Service Personnel refer to Maintenance & War-

ranty section for service of any type.

Operation:

1. This heater must be properly installed in accordance

OPERATING INSTRUCTIONS

W Series Heater

SAVE THESE INSTRUCTIONS

with the National Electrical Codes (NEC) & local

electrical codes before it is used.

2. After the electric heater has been completely in-

stalled, all thermostats should be turned to LOW or

NO HEAT. Turn ON breakers, wait 3 to 5 minutes and

check to see that the heaters are not operating. If

operating, disconnect power and check for improper

wiring. If none are operating then turn thermostats

to highest position and wait 3 to 5 minutes. Check to

see that all heaters are operating. Should any not be

operating, disconnect power and check wiring.

3. Allow entire system to operate steadily for 1/2 hour.

This should remove oily residue from manufacturing.

(Some smoking may occur).

4. Select the setting for comfort on all thermostats.

5. A safety limit control is provided to turn off the

heater automatically if it is blocked or otherwise

overheats due to an abnormal condition. DO NOT

bypass or remove this safety device from the electri-

cal circuit-see Warning Figure 3 on page 2. During

normal use, this safety control should not operate. If

you find that this control is operating, make sure the

heater is not being blocked. If it continues to cycle

the heater off, disconnect power to heater and have

it checked and repaired by a qualified electrician.

Troubleshooting Chart for Electric Heaters

SYMPTOM PROBLEM SOLUTION

Breaker Trips Short Circuit 1.

2. Overloaded Circuit

3. Improper Voltage

Find source of short. Trace heater circuit and verify the heater is wire properly.

Reduce wattage in circuit. Refer to circuit sizing table for maximum wattage.

3. Verify the heater voltage matches the supply voltage.

Heater not working 1. No Power

2. Loose Connections

3. Defective Limit

1. Turn Breaker ON, turn thermostat ON, check that the breaker is position

properly on panel bus-bar. A 2-Pole breaker must be connected to both bus-

bars (A&B phase) to produce 240V power.

2. Tighten wire connections.

3. -pass the limit to test. If heater works, replace the limit. By

Heater Smokes 1. Oil on Element

2. Needs Cleaning

1. It is normal for the element to burn off some light finishing oil used in the

manufacturing process when first energized. Open windows and allow room

to vent until it stops, usually within a few minutes.

2. Remove any dust or dirt accumulations.

Room Temperature

does not match

thermostat setting

1. Thermostat affected

by another heat

source.

2. Improper calibration

1. Sunlight or other heat sources can affect the thermostat. Move the thermo

stat to another location or remove the heat source.

2. Remove cover and adjust calibration screw.

Room Temperature

swings from too hot

to too cold

1. Defective or low

quality thermostat

1. Replace with a better quality thermostat. Anticipated thermostats are

fairly accurate; an electronic thermostat is best.

Specyfikacje produktu

Marka:	King
Kategoria:	Podgrzewacz
Model:	WSC1215-T-B

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z King WSC1215-T-B, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Podgrzewacz King

King H612 Instrukcja

25 Września 2024

King TW2-33B2-C25 Instrukcja

25 Września 2024

King ECO2S+ KB2407-1-ECO2S-PLUS Instrukcja

15 Września 2024

King KCF2-2420-1-S-T2 Instrukcja

11 Września 2024

King KCF4-2050-1-S-T-DS1 Instrukcja

11 Września 2024

King KCF4-2050-3-R-T-DS3 Instrukcja

11 Września 2024

King PCKF2420-3 Instrukcja

10 Września 2024

King KCV2406-W Instrukcja

10 Września 2024

King KCF4-2450-1-S-T Instrukcja

9 Września 2024

King PlatinumX KB2407-1-PLTMX Instrukcja

8 Września 2024

Instrukcje Podgrzewacz

Najnowsze instrukcje dla Podgrzewacz

Trotec TDS 75 R Instrukcja

14 Stycznia 2025

Thomson THSF022 Instrukcja

14 Stycznia 2025

Breville the Smart Tilt Control Max LCE308 Instrukcja

14 Stycznia 2025

Breville BodyZone BZB437 Instrukcja

14 Stycznia 2025

Duux Edge Oil Instrukcja

14 Stycznia 2025

SVAN SVCA2000RP Instrukcja

13 Stycznia 2025

Dimplex DX 521 Instrukcja

13 Stycznia 2025

Bestron AFH211G Instrukcja

13 Stycznia 2025

Vonroc PH503AC Instrukcja

11 Stycznia 2025

JANDY VersaFlo Instrukcja

11 Stycznia 2025