Instrukcja obsล‚ugi King PCKF4825-3

King Podgrzewacz PCKF4825-3

Przeczytaj poniลผej ๐Ÿ“– instrukcjฤ™ obsล‚ugi w jฤ™zyku polskim dla King PCKF4825-3 (2 stron) w kategorii Podgrzewacz. Ta instrukcja byล‚a pomocna dla 6 osรณb i zostaล‚a oceniona przez 2 uลผytkownikรณw na ล›rednio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
1. Read all instructions before using this heater.
2. WARNING: This heater is hot when in use. To
avoid burns, do not let bare skin touch hot
surfaces. Keep combustible materials, such as
furniture, pillows, bedding, papers, clothes, etc.
and curtains at least 3 feet (0.9 m) from the
front of the heater and keep them away from the
sides and rear.
3. Extreme caution is necessary when heater is used
by or near children or invalids and whenever the
heater is left operating and unattended.
4. Always unplug heater when not in use.
5. WARNING: Do not operate heater with damaged
cord or plug, after it malfunctions, has been
dropped, or damaged in any manner. Discard
heater or return to authorized service facility for
examination and/or repair.
WARNING: Do not run cord under carpeting. Do
not cover cord with throw rugs, runners, or
similar coverings. Do not route cord under
furniture or appliances. Arrange cord away from
IMPORTANT INSTRUCTIONS
ELECTRIC SHOCK OR FIRE HAZARD
DANGER
! !
WARNING
! !
Read Carefully - These instructions are written in an effort to prevent potential difficulties that might arise during
installation. Studying the instructions first may save you considerable time and money later. Observing the following
procedures will keep installation time to a minimum. Save these instructions for future use.
Portable Heaters
IMPORTANT INSTRUCTIONS
When using electrical heating appliances, basic precautions should always be followed to reduce the risk of fire, electric
shock and injury to persons, including the following:
traffic area and where it will not be tripped over.
To disconnect heater, turn controls to off, then
remove plug from outlet๎˜ƒWR๎˜ƒSUHYHQW๎˜ƒDUFKLQJ.
Connect to properly grounded outlets only.
WARNING: Do not insert or allow foreign objects
to enter any ventilation or exhaust opening as this
may cause an electric shock or fire, or damage
the heater.
WARNING: To prevent a possible fire, do not block
air intakes or exhaust in any manner.
WARNING: A heater has hot and arcing or sparking
parts inside. Do not use it in areas where gasoline,
paint, or flammable vapors or liquids are used or
stored.
Use this heater only as described in this manual.
Any other use not recommended by the
manufacturer may cause fire, electric shock, or
injury to persons.
Always receptacle๎˜ƒplug heater into a wall outleW๎˜ƒ ๎˜ƒRU
FRUG๎˜ƒ FRQQHFWRU ๎˜ƒ XQGHUVL]HG. Never use with an
extension cord or๎˜ƒrelocatable power tap, outlet, or
power strip๎˜‘
!
SAVE THESE INSTRUCTIONS
!
!
!
!
!
!
!
!
!
!
!
!
1
-
-
Item #103610 12-16-19
4
PCKF Series
Instructions include all units in the PCKF Series
This heater is not intended for use in bathrooms,
laundry and similar indoor areas. Never locate
heater where it can fall into a bathtub or other
water container.
! 6.
7.
8.
9.
10.
11.
12.
13.
14.
Figure 1
Figure 3
PKB SETUP INSTRUCTIONS
Rating Label Location
1. Setting up Your Heater:
2. Unpack and inspect your heater for any damage. Any
damage discard heater or return to authorized
service facility immediately.
3. Place heater at least 6" (15cm) away from vertical
surfaces clear ofand keep the intake๎˜ƒDQG๎˜ƒH[KDXVW
obstructions. Keep all combustible materials, such๎˜ƒ
as furniture, papers, clothes, drapes, ๎˜ƒand curtains
at least 3 feet (0.9 m) of the heater๎˜ƒfrom the front
and keep them away from the sides and rear.๎˜ƒ
4. Route power cord away from traffic areas to avoid
tripping. NEVER rout power cord under carpets,H
rugs, drop๎˜ƒFORWKV๎˜ furniture or other equipment.
5. Plug power cord into a grounded wall outlet only DO
NOT use an extension cord or power strip.
6. Wiring in wiring diagram located FRPSDUWPHQW๎˜‘
ELECTRIC SHOCK OR FIRE HAZARD
DANGER
! !
2
Figure 2
)LJXUH๎˜ƒ๎˜—
3DUW๎˜†๎˜ƒ๎˜•๎˜”๎˜—๎˜” %๎˜—
๎˜–๎˜“$๎˜ƒ๎˜™๎˜“๎˜“9๎˜ƒ$&๎˜ƒ๎˜•๎˜˜๎˜“9๎˜ƒ๎˜ƒ๎˜ƒ
๎˜–๎˜SROH๎˜ƒ๎˜—๎˜ƒZLUH๎˜ƒFRQQHFWRU
๎˜˜๎˜“$๎˜ƒ:HDWKHUSURRI๎˜ƒ%RRWV
๎˜˜๎˜“$๎˜ƒ ๎˜ƒ$&๎˜ƒ๎˜ƒ๎˜ƒ,3๎˜•๎˜“
๎˜–๎˜SROH๎˜ƒ๎˜—๎˜ƒZLUH๎˜ƒSOXJ
&$87,21๎˜„๎˜ƒ7XUQ๎˜ƒ2))๎˜ƒEUHDNHU๎˜ƒWR๎˜ƒUHPRYH๎˜ƒDQG๎˜ƒ
XQ๎˜SOXJJLQJ๎˜ƒWKH๎˜ƒKHDWHU๎˜ƒZKLOH๎˜ƒVHWWLQJ๎˜ƒXS๎˜ƒRU๎˜ƒ
SODFLQJ๎˜ƒLQ๎˜ƒQHZ๎˜ƒORFDWLRQ๎˜‘
:HDWKHUSURRI๎˜ƒSOXJ๎˜ƒDQG๎˜ƒFRQQHFWRUV +XEEOH๎˜ƒ0RGHOV๎˜๎˜ƒ
3DUW๎˜†๎˜ƒ&6๎˜™๎˜–๎˜™๎˜—&๎˜ƒ๎˜—๎˜›๎˜“9๎˜ƒ๎˜–๎˜ƒSKDVH
3DUW๎˜†๎˜ƒ+%/๎˜š๎˜š๎˜”๎˜š&
3DUW๎˜†๎˜ƒ+%/๎˜š๎˜š๎˜”๎˜™&
๎˜–๎˜“$๎˜ƒ๎˜”๎˜•๎˜˜๎˜’๎˜•๎˜˜๎˜“9๎˜ƒ$&๎˜ƒ๎˜ƒ๎˜ƒ
๎˜–๎˜SROH๎˜ƒ๎˜—๎˜ƒZLUH๎˜ƒSOXJ ๎˜–๎˜“$๎˜ƒ:HDWKHUSURRI๎˜ƒ%RRWV
3DUW๎˜†๎˜ƒ+%/๎˜•๎˜”๎˜—๎˜”๎˜˜%
3DUW๎˜†๎˜ƒ+%/๎˜•๎˜“๎˜—๎˜•๎˜—%
3DUW๎˜†๎˜ƒ+%/๎˜•๎˜“๎˜—๎˜•๎˜˜
)LJXUH๎˜ƒ๎˜˜ )LJXUH๎˜ƒ๎˜™
3DUW๎˜†๎˜ƒ&6๎˜›๎˜•๎˜™๎˜—&๎˜ƒ๎˜•๎˜—๎˜“9๎˜ƒ๎˜–๎˜ƒSKDVH
3DUW๎˜†๎˜ƒ&6๎˜™๎˜–๎˜™๎˜˜&๎˜ƒ๎˜—๎˜›๎˜“9๎˜ƒ๎˜–๎˜ƒSKDVH
3DUW๎˜†๎˜ƒ&6๎˜›๎˜•๎˜™๎˜˜๎˜ƒ๎˜•๎˜—๎˜“9๎˜ƒ๎˜–๎˜ƒSKDVH
๎˜˜๎˜“$๎˜ƒ๎˜”๎˜•๎˜˜๎˜’๎˜•๎˜˜๎˜“9๎˜ƒ$&๎˜ƒ๎˜–๎˜SROH๎˜ƒ๎˜ƒ
๎˜—๎˜ƒZLUH๎˜ƒFRQQHFWRU
32
-
-
General information and Guidelines:
This heater must be properly placed before it is used.
DO NOT tamper with or change the operating of this
heater. All service should be preformed by a authorized
service representative. Only replace components with
King approved replacement parts.
Operation:
1. After the been ,electric heater has VDIHO\๎˜ƒORFDWHG
thermostat to LOW or NO HEAT.should be turned ๎˜ƒ
Plug unit into grounded outlet, to 5 minuteswait 3 ๎˜ƒ
and check to๎˜ƒsee heater operating. Ifthat the ๎˜ƒLV not๎˜ƒ
operating, disconnect power for improper๎˜ƒand check๎˜ƒ
wiring. If no operating then turn thermostats to๎˜ƒW ๎˜ƒ
highest position to 5 minutes. ๎˜ƒand wait 3 ๎˜ƒCheck to
see that๎˜ƒWKH
OPERATING INSTRUCTIONS
Unit or Series
SAVE THESE INSTRUCTIONS
heater operating. Should not be operating,LV LW ๎˜ƒ
disconnect power and check wiring.
2. Allow entire system to operate steadily for 1/2 hour.
This should remove oily residue from manufacturing.
(Some smoking may occur ).๎˜ƒIURP๎˜ƒHOHPHQW
3. Select the setting for comfort๎˜ƒRU๎˜ƒ\RXU๎˜ƒMRE๎˜ƒUHTXLUHPHQW๎˜‘
4. A safety limit control is turn off theprovided to ๎˜ƒ
heater HOHPHQWV๎˜ƒautomatically if it is blocked or
otherwise overheats due to an abnormal condition.๎˜ƒ
DO NOT bypass or safety device ๎˜ƒremove this OLPLWLQJ๎˜ƒ
from the๎˜ƒelectrical circuit. During normal use, this
safety control should not operate. If you ๎˜ƒfind that
this control is operating, make sure the heater is not๎˜ƒ ๎˜ƒ
being blocked . If it continues to๎˜ƒRU๎˜ƒILOWH ๎˜ƒSOXJJHGU๎˜ƒLV ๎˜ƒ
cycle the heater off, to ๎˜ƒHOHPHQWV๎˜ƒ disconnect power
heater and have it checked and repaired by a ๎˜ƒ๎˜ƒ
qualified electrician.๎˜ƒ
Table ๎˜”
Troubleshooting Chart for Electric Heaters
SYMPTOM PROBLEM SOLUTION
Breaker Trips 1. Short Circuit
2. Overloaded Circuit
3. Improper Voltage
1.
Find source of short. Trace heater circuit and verify the heater is wire properly.
2.
Reduce wattage in circuit. Refer to circuit sizing table for maximum wattage.
3. Verify the heater voltage matches the supply voltage.
Heater not working 1. No Power
2. Loose Connections
3. Defective Limit
1. Turn Breaker ON, turn thermostat ON, check that the breaker is position
properly on panel bus-bar. A 2-Pole breaker must be connected to both bus-
bars (A&B phase) to produce 240V power.
2. Tighten wire connections.
3. By-pass the limit to test. If heater works, replace the limit.
Heater Smokes 1. Oil on Element
2. Needs Cleaning
1. It is normal for the element to burn off some light finishing oil used in the
manufacturing process when first energized. Open windows and allow room
to vent until it stops, usually within a few minutes.
2. Remove any dust or dirt accumulations.
Room Temperature
does not match
thermostat setting
1. Thermostat affected
by another heat
source.
2. Improper calibration
1. Sunlight or other heat sources can affect the thermostat. Move the thermo
stat to another location or remove the heat source.
2. Remove cover and adjust calibration screw.
Room Temperature
swings from too hot
to too cold
1. Defective or low
quality thermostat
1. Replace with a better quality thermostat. Anticipated thermostats are fair-
ly accurate; an electronic thermostat is best.
PCKF SETUP INSTRUCTIONS
8. WARNING: This heater is floor ONLY and should not
be tipped on side, placed upside down, mounted on
or inserted into a wall. A tip over auto disconnect
switch will activate when tipped more then 30ยฐ.
9. DO NOT use heater in areas where gasoline, paint,
or other flammable liquids are used.
10.
11. Store unplugged and in a dry indoor location.
12. 7KH๎˜ƒSURSHU๎˜ƒWZLVW๎˜ƒORFN๎˜ƒFRUG๎˜ƒFRQQHFWLRQ๎˜ƒKDV๎˜ƒEHHQ
SURYLGHG๎˜ƒDQG๎˜ƒORQJHU๎˜ƒFRUGV๎˜ƒFDQ๎˜ƒEH๎˜ƒDGGHG๎˜‘๎˜ƒ'R๎˜ƒQRW๎˜ƒFRLO
XS๎˜ƒWKH๎˜ƒH[WHQWLRQ๎˜ƒFRUG๎˜ƒZKLOH๎˜ƒWKH๎˜ƒKHDWHU๎˜ƒLV๎˜ƒLQ
RSHUDWLRQ๎˜๎˜ƒKHDW๎˜ƒLV๎˜ƒPXOWLSOLHG๎˜ƒZLWK๎˜ƒHYHU\๎˜ƒWXUQ๎˜ƒDQG๎˜ƒZLOO
PHOW๎˜ƒWKH๎˜ƒFRUG๎˜‘
Make sure covers are fastened with the provided
rubber sealing washers for the access door.

Specyfikacje produktu

Marka: King
Kategoria: Podgrzewacz
Model: PCKF4825-3

Potrzebujesz pomocy?

Jeล›li potrzebujesz pomocy z King PCKF4825-3, zadaj pytanie poniลผej, a inni uลผytkownicy Ci odpowiedzฤ…


Instrukcje Podgrzewacz King

King

King H612 Instrukcja

25 Wrzeล›nia 2024
King

King TW2-33B2-C25 Instrukcja

25 Wrzeล›nia 2024
King

King ECO2S+ KB2407-1-ECO2S-PLUS Instrukcja

15 Wrzeล›nia 2024
King

King KCF2-2420-1-S-T2 Instrukcja

11 Wrzeล›nia 2024
King

King KCF4-2050-1-S-T-DS1 Instrukcja

11 Wrzeล›nia 2024
King

King KCF4-2050-3-R-T-DS3 Instrukcja

11 Wrzeล›nia 2024
King

King PCKF2420-3 Instrukcja

10 Wrzeล›nia 2024
King

King KCV2406-W Instrukcja

10 Wrzeล›nia 2024
King

King KCF4-2450-1-S-T Instrukcja

9 Wrzeล›nia 2024
King

King PlatinumX KB2407-1-PLTMX Instrukcja

8 Wrzeล›nia 2024

Instrukcje Podgrzewacz

Najnowsze instrukcje dla Podgrzewacz

Trotec

Trotec TDS 75 R Instrukcja

14 Stycznia 2025
Thomson

Thomson THSF022 Instrukcja

14 Stycznia 2025
Breville

Breville the Smart Tilt Control Max LCE308 Instrukcja

14 Stycznia 2025
Breville

Breville BodyZone BZB437 Instrukcja

14 Stycznia 2025
Duux

Duux Edge Oil Instrukcja

14 Stycznia 2025
SVAN

SVAN SVCA2000RP Instrukcja

13 Stycznia 2025
Dimplex

Dimplex DX 521 Instrukcja

13 Stycznia 2025
Bestron

Bestron AFH211G Instrukcja

13 Stycznia 2025
Vonroc

Vonroc PH503AC Instrukcja

11 Stycznia 2025
JANDY

JANDY VersaFlo Instrukcja

11 Stycznia 2025