Instrukcja obsługi Kicker ZX200.4

Kicker Radia samochodowe ZX200.4

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kicker ZX200.4 (10 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/10

MULTI-CHANNELAMPLIFIER

ZX200.4

English Version

Versión spañolE

Amplificador del la Serie ZX.4

Manual del Propietario

Deutsche Version

Stereoverstärker der ZX.4-Serie

Benutzerhandbuch

Version Française

Amplificateur de série ZX.4

Manuel d'utilisation

Installation . . . as easy as 1, , 32

1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The amplifier’s

end-panel controls need to be accessible for adjustment. Make sure there are no items behind the area

where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for

the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four

holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifier.

. Wiring

Disconnect the vehicle’s battery to avoid an electrical short. Then connect the ground wire

to the amplifier. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and

corrosion-free solid-metal area of the vehicle's

chassis.

Use a twisted pair(s) of RCA (low-level)

interconnect cable to feed the audio signal to

the amplifier. If you are using only one pair of

RCA inputs, connect the RCA cable to the AMP

1 inputs. Push the fader button out, and all four

channels will work with a single pair of RCA

input cable. Push the fader button in, when

using two pairs of RCA input cables. Keep the

RCA cable away from factory wiring harnesses

and other power wiring. If you need to cross this

wiring, cross it at a 90 degree angle.

Only use speaker wire (high-level) inputs if

your source unit does not have RCA type outputs. If you are using only one pair of high-level inputs,

connect the speaker wire to the AMP 1 input. Push the fader button out, and all four channels will work

with a single high-level input cable. Push the fader button in, when using both sets of high-level inputs.

Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your

amplifier. If you ever need to remove the amplifier from the vehicle after it has been installed, the ground

wire should be the last wire disconnected from the amplifier--just the opposite as when you installed it.

See the chart below for power and ground wire size, and fusing recommendations.

3. Configuration The following diagrams show the most common configurations for your Kicker ZX

series amplifier.

Four C

hannel Operation (Stereo)

These ZX amplifiers are capable of operating into a minimum

impedance of 2 ohms per channel in stereo operation. See Figure 2.

Bridged Operation (Mono) ZX.4 series amplifiers are capable of operating into a minimum

impedance of 4 ohms when in bridged operation. See Figure 3.

Stereo and Bridged Operation Simultaneously The ZX.4 series amplifiers are capable of operating

into a minimum impedance of 4 ohms bridged and 2 ohms per channel in stereo operation. See

Figure 4.

INSTALLATION

ZX 4AMPLIFIER

ZX200.4

FourChannelModel:

ZX.4SeriesAmplifier

Owner’sManual

Congratulations on your

KIC EK R purchase

Please record your purchase

information and keep your sales

receipt for validation of warranty.

Authorized Kicker Dealer:

Purchase Date:

Amplifier Model Number:

Amplifier Serial Number:

__________________________

killers trk7“on Top”

RCA

I PN UTS

BASS

INGAINBASS

HI-LEVEL

I P TN U

+ - - +

H LEI- VEL

I P TN U

+ - - +

A AMP 1 MP 2

OFF I O H L

XOVER

OFF HI O L

XOVER

F D RA E

ON OFF

Model FuseZX200.4 30APowerG d 8rounWire GA

Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring.

+-+-

Battery

+12V Fuse

Right Speaker AMP 2

Left Speaker AMP 2

18"

Or Less

(45cm)

Signal In AMP 1

Minim ance peratium imped of 2 ohms per channel in stereo o on

Signal In AMP 2

Right Speaker AMP 1

Left Speaker AMP 1

24"

Or Less

(60cm)

G droun

Rem teo

Turn-On

Battery

+12V Fuse

18"

Or Less

(45cm)

Signal In AMP 1

Minim m impe ance f hms when in bri ge peratiu d o 4 o d d o on

Signal In AMP 2

M no o Speaker AMP 1

M no o Speaker AMP 2

24"

Or Less

(60cm)

G droun

Remote

Turn-On

Battery

+12V Fuse

18"

Or Less

(45cm)

Signal In AMP 1

Minim ance f ge peratium imped o 4 o hms when in brid d o on

an peratid 2 ohms per channel in stereo o on

Signal In AMP 2

Right Speaker AMP 1

M no o Speaker AMP 2

Left Speaker AMP 1

24"

Or Less

(60cm)

G droun

Remote

Turn-On

Figure 1

Figure 2

Figure 3

Figure 4

U u ,se o only ne type of signal inp t to the amplifier

either able Speaker CR A C or Wire

R AC Cable

(L el)ow-Lev

AMP 1

Speaker Wire

(High-Level

Output)

Speaker Wire

(High-Level Input)

AMP 1

Left +

Left -

Right -

Right +

C N GU AO FI R TION

ZX200.4

Speaker Wire

(High-Level Input)

AMP 2

Fa er shd uB tto un: P in of r

2 f p t pairs o inputs, ush ou

f r a fo single pair o inputs.

R AC Cable

(L el)ow-Lev

AMP 2

Left +

Left -

Right -

Right +

Operation

Your Kicker ZX.4 series amplifier has four rotary controls and two switches on the end-panel. Before

turning on the system for the first time, turn the four rotary controls on the side of the amplifier to the full

counter-clockwise position.

1. CrossoverSwitch The crossover switches on the end-panel are for setting the internal crossovers.

In the OFF position the amplifier

passes a full-range signal to the

speakers. Use the LO position when

connected to a subwoofer. The HI

position should be selected when

connected to speakers, which you

do not want to receive any sub-bass

information. Never change the

crossover "OFF/HI/LO" switch

setting with the audio system on!

2 G. Input ainControl The input gain control is not a volume control. It matches the output of the

source unit to the input level of the amplifier. Turn the source unit up to about 3/4 volume (if the source

unit goes to 30, turn it to 25). Next, slowly turn (clockwise) the gain on the amplifier up until you can

hear audible distortion, then turn it down a little. Adjust AMP 1, then proceed to AMP 2.

3. BassBoostControl The bass boost control is designed to give you increased output 0 - 12dB

at 40 Hz. The setting for this control is subjective. If you turn it up, you must go back and adjust the

input gain control to avoid clipping the amplifier.

Trouble Shooting

If your amplifier does not appear to be working, check the obvious things first such as blown fuses,

poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There

are two LEDs on the top of your Kicker ZX series amplifier, one green and one red. When the green

LED is lit this indicates the amplifier is turned on and no trouble exists. If the green LED turns off and

the red LED is lit, this indicates that the protection circuitry (SORT) is engaged.

Green LED off, no output? With a Volt Ohm Meter (VOM) check the following: 1) +12 volt power

terminal (should read +12V to +16V) 2) Remote turn-on terminal (should read +12V to +16V)

3) Check for reversed power and ground connections 4) Ground terminal, for proper conductivity.

Green LED on, no output? Check the following: 1) RCA connections 2) Test speaker outputs

with a “known” good speaker. 3) Substitute source unit with a “known” good source unit. 4) Check

for a signal in the RCA cable feeding the amplifier with the “AC” test position selected on the VOM

meter.

 Red LED on, no output? 1) Amplifier is very hot. Thermal protection is engaged. Test for proper

impedance at the speaker terminals with a VOM meter (see the diagrams in this manual for minimum

recommended impedance and multiple speaker wiring suggestions). Also check for adequate airflow

around the amplifier. 2) Amplifier shuts down only while vehicle is running. Voltage protection

circuitry is engaged. Voltage to the amplifier is not within the 9-16 volt operating range. Have the

vehicle's charging and electrical system inspected. 3) Amplifier will only play at low volume levels.

Short circuit protection is engaged. Check for speaker wires shorted to each other or to the vehicle

chassis. Check for damaged speakers, or speaker(s) operating below the minimum recommended

impedance.

No output from one channel? 1) Check the balance control on source unit 2) Check the RCA (or

speaker input) and speaker output connections for the channel 3) Swap the RCA (or speaker input)

cable from left to right. If the problem changes sides then you have a bad RCA (or speaker input) cable

or source unit problem. 4) Swap the speaker output wire from left to right. If the problem changes

sides then you have a bad speaker cable, passive crossover network and/or speaker.

Alternator noise-whining sound with engine’s RPM? 1) Check for damaged RCA (or speaker

input) cable 2) Check the routing of RCA (or speaker input) cable 3) Check the source unit for proper

grounding 4) Check the gain settings and turn them down if they are set too high.

 Poor stereo image or reduced bass response? Check system phasing by turning the balance

control from left to right. If there is more bass output when turned to either side, then check your

speaker wiring, passive crossover networks and speaker terminals for proper positive and negative

connections. Reverse a speaker connection from positive to negative on the stereo/subwoofer

channel(s); if the bass improves, the speaker was out of phase.

 G L Nround- oop oise? If you are using only one pair of RCA inputs, connect the RCA cable to the

AMP 1 inputs.

 No Fader? When using both sets of low-level (RCA) or high-level (speaker wire) inputs, the fader

button must be pushed in.

If you have more questions about the installation or operation of your new KICKER product, see the

Authorized KICKER Dealer where you made your purchase. For more advice on installation, click on the

SUPPORT tab on the Kicker homepage, www.kicker.com. Choose the TECHNICAL SUPPORT tab,

choose the subject you are interested in, and then download or view the corresponding information.

Please E-mail support@kicker.com or call Technical Services (405) 624-8583 for unanswered or specific

questions.

Please Note: Modern high performance speakers have a lower DC Resistance than what used to be available. The

Kicker Coaxial and Component speakers are rated at four ohms (some DC Resistances may be as low as 3 ohms)

and work with any amplifier designed to operate at a four ohm load. If you want to use two Kicker Coaxial or

Component speakers on a single channel of your amplifier wire the speakers in series. This will improve the sound

quality, lower the total harmonic distortion and lessen the thermal load at the amplifier. This may prevent an amplifier

from shutting down, due to over-current protection circuitry.

CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct. Improper

connections can result in blown amplifier fuses as well as the failure of other critical systems in the vehicle.

Performance

Model ZX200.4

RMS Power in Watts, all channels driven

@ 14.4 Volts, 4Ωstereo, ≤1% THD+N 35 x 4

@ 2 1% THD+N 50 x 4Ωstereo, ≤

@ 4 1% THD+N 100 x 2Ωmono, ≤

Frequency Response, ±0.5 dB: 20 Hz - 20 kHz

Signal-to-Noise Ratio: 95 dB, a-weighted, re: rated power>

Input Sensitivity: 125 mV - 5 V low level

250 mV - 10 V high level

Electronic Crossover: HI, LO or OFF (bypass),

fixed @ 80 Hz, 12 dB per octave

Bass Boost: Variable 0 to +12 dB boost @ 40 Hz

Height: 2 1/8” (54mm)

Width: 9 5/8” (244mm)

Length: 10 1/4” (260mm)

ZX 4AMPLIFIER

AMP 1

Bass Boo Cost ntrol

0-12 dB @ 4 H0 z

AMP 2

Bass Boo Cost ntrol

0-12 dB @ 4 H0 z

Inp ain ntru Gt Co ol AMP 1 Inp ntru Gt ain Co ol AMP 2

Selectable AMP 2

C or ssover Switch

Set @ 8 H0 z

Selectable AMP 1

C or ssover Switch

Set @ 8 H0 z

RCA

I PN UTS

BASS

INGAINBASS

HI-LEVEL

I P TN U

+ - - +

H ELI-LEV

I P TN U

+ - - +

A AMP 1 MP 2

OFF HI LO

XOVER

OFF HI O L

XOVER

F D RA E

ON OFF

Figure 5

PERFORMANCE

OPE AR TION

Model .4ZX200

3 d H ,5 x 4 @ 4 ohms, 14.4V c, 1% T D

CEA-2006 W( atts)

Signal ise Rati to No o - 58

CE : A-2006 (ref 1W, A-weighted)

NOTE: All specifications and performance figures are subject to change. Please visit the www.kicker.com for the most current information.

Specyfikacje produktu

Marka:	Kicker
Kategoria:	Radia samochodowe
Model:	ZX200.4

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Kicker ZX200.4, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Radia samochodowe Kicker

Kicker KX300.4 Instrukcja

4 Października 2024

Kicker IX 1302 Instrukcja

1 Października 2024

Kicker KX100.2 Instrukcja

29 Września 2024

Kicker X50 Instrukcja

25 Września 2024

Kicker zx 350 2 Instrukcja

24 Września 2024

Kicker KX 400.4 Instrukcja

24 Września 2024

Kicker ZX 300.1 Instrukcja

23 Września 2024

Kicker kx 600 1 Instrukcja

23 Września 2024

Kicker zr 120 Instrukcja

23 Września 2024

Kicker KX 800.4 Instrukcja

23 Września 2024

Instrukcje Radia samochodowe

Najnowsze instrukcje dla Radia samochodowe

JVC KD-R90BT Instrukcja

15 Października 2024

Kenwood KMM-X705 Instrukcja

15 Października 2024

Alpine CDM-7870R Instrukcja

14 Października 2024

Hyundai H-CMD2009 Instrukcja

14 Października 2024

Dual XC4100 Instrukcja

13 Października 2024

Audiovox VXE 3010 Instrukcja

13 Października 2024

MB Quart PAB 5400 Instrukcja

13 Października 2024

Hyundai H-CDM8023 Instrukcja

13 Października 2024

Caliber RCD110B Instrukcja

13 Października 2024

JVC KD-X30 Instrukcja

13 Października 2024