Instrukcja obsługi Kicker sx 700 4

Kicker Radia samochodowe sx 700 4

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kicker sx 700 4 (20 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/20
3
SX .4 Series Amplifiers
Features
Features
Low Impedance Operation Stable into 2 ohm stereo
or 4 ohm mono loads.
SORT Protection Circuitry (Short circuit, Over-voltage,
Reverse polarity, Thermal) Protects amplifier from accidents
and out of spec operation.
MOSFET Power Supply Provides high efficiency
operation.
PAST (Pre Amp Signal Transfer) Output RCA jacks to pass the
incoming signal to another amplifier or component.
SAMS (Stereo And Mono Simultaneously) Amplifier will
operate into a bridged mono load and a stereo load at the
same time.
Low Pass Filter Fully adjustable digital crossover with
variable slope and crossover frequency. 30 Hz - 20 kHz in 1/12
octave spacing. OFF - 36 dB per octave slope in 6 dB incre-
ments.
High Pass Filter Fully adjustable digital crossover with
variable slope and crossover frequency. 10 Hz - 16 kHz in 1/12
octave spacing. OFF - 36 dB per octave slope in 6 dB incre-
ments.
KickEQ Fully adjustable single band digital parametric equal-
izer with variable Q (bandwidth), variable center frequency and
variable boost or cut. Q range .5 - 10 in .5 steps. Center
frequency 20 Hz - 20 kHz in 1/12 octave steps. Boost or cut
range +/- 18 dB.
Adjustable Phase The output phase of each channel can
be set at 0 Degrees or 180 Degrees. Left and Right channels
can be linked or independently adjusted.
UltraMatch Gain Structure Digital input gain control
with five selectable gain ranges (1 volt, 2 volt, 4 volt, 8 volt, 16
volt) with 12 dB of adjustment in each range in .5 dB steps.
Left and Right channels can be linked or adjusted independ-
ently.
SickBay and On Board Diagnostics Various tools to
troubleshoot installation issues and check amp status.
Kompressor A 4-setting, user-selectable bass compressor
used to fatten up your sub bass. OFF, RED-LINE, CONTOUR and
ATTACK with +/- 24 dB of adjustment to compensate for
speaker size, speaker location, vehicle size or listening style.
ISIS (pronounced eye-sis) (Indicate Status & Input Settings)
The user interface to view or adjust current settings and check
the status of your Kicker SX amplifier.
BLAST Port (Bass Level And Signal Transfer) Provides
Remote Bass Level Control and control signal transfer
between multiple SX amplifiers.
EndKaps Cast aluminum, custom, removable covers to pro-
tect and hide all your wiring connections to the amplifier. Can
be prepped and painted any custom color you choose.
SASA (Shake A Stick At) So many more features...it is more
than you can Shake A Stick At. (It’s an Oklahoma thing!) Read
on to find out!
2SX .4 Series Amplifiers
Introduction
SX700.4 / SX900.4
SX .4 Series
Amplifier
Owners Manual
Four Channel Models:
Attention:
Please take a moment and record the information
asked for below in the provided area. It is also a good
idea to attach the original sales receipt or a copy of it to
this page for future reference
If for any reason you require service on this amplifier
during the warranty period, you will need to provide this
information and a copy of the receipt to Kicker to vali-
date your warranty.
ALWAYS KEEP YOUR RECEIPT!
Dealer Where Purchased:
Purchase Date:
Amplifier Model Number:
Amplifier Serial Number:
Congratulations!
You have just purchased the latest in amplifier
technology to carry the famous KICKER name.
Your KICKER SX series amplifier employs the lat-
est in DSP signal processing to give you total
control over your sound. Like all KICKER prod-
ucts it is designed and built to give you years
of powerful and trouble-free performance.
This installation manual contains valuable infor-
mation on how to get the most out of your
new SX series amplifier.
Thanks for buying KICKER. Enjoy!
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
5
SX .4 Series Amplifiers
Features
VFD DISPLAY - cont
GAIN - Indicates you are in the gain menu.
EQ - Indicates you are in the equalizer menu.
LPF - Indicates you are in the low pass filter menu.
HPF - Indicates you are in the high pass filter menu.
PHASE - Indicates you are in the phase menu.
KOMP - Indicates you are in the Kompressor menu.
MEM-1 - Memory preset 1 activated.
MEM-2 - Memory preset 1 activated.
MEM-3 - Memory preset 1 activated.
MEM-4 - Memory preset 1 activated.
KEYPAD
The keypad consists of nine buttons that allow you to adjust
your amplifier.
M1 - Used to select memory preset 1 or to store cur-
rent settings into preset 1.
M2 - Used to select memory preset 2 or to store
current settings into preset 2.
M3 - Used to select memory preset 3 or to store
current settings into preset 3.
M4 - Used to select memory preset 4 or to store
current settings into preset 4.
ESC - Used to exit the current menu.
ENT - Used to enter the selected menu.
HOME - Used to return to the Main menu and
other functions explained later.
UP - Used to advance up through menu selections
and/or adjust amplifier controls.
DOWN - Used to advance down through menu
selections and/or adjust amplifier controls.
These controls and their usage will be explained later with
more detail in each menu usage section.
ESC
M2
M3
M4
ENT
HOME
M1
4SX .4 Series Amplifiers
Features
ISIS VFD Display
SYS
MEM-1
GAIN EQ LPF HPF KOMP
AMP1
LOCK
MEM-2 MEM-3 MEM-4
PHASE
MUTE
AMP2
LEFT RIGHT
** kicker
Meet the ISIS interface (Indicate Status & Input Settings).
The ISIS (pronounced eye-sis) allows you to view the cur-
rent conditions and settings of your amplifier as well as
change the many user-adjustable settings.The ISIS system
consists of the VFD (Vacuum Fluorescent Display) and the nine
soft touch buttons that make up the KEYPAD.
M1 M2 M3 M4
ESC ENT
HOME
SYS
MEM-1
GAIN EQ LPF HPF KOMP
AMP1
LOCK
MEM-2 MEM-3 MEM-4
PHASE
MUTE
AMP2
LEFT RIGHT
** kicker
ISIS
VFD
ISIS
KEYPAD
Here is a brief description of the indicators found on the
VFD.
AMP1 - Indicates amplifier 1 is selected for adjustment.
AMP2 - Indicates amplifier 2 is selected for adjustment.
LOCK - Indicates the amplifier controls are locked out and
not usable.
LEFT - Indicates an action or adjustment of the left channel.
SYS - Indicates you are in the system menu.
RIGHT - Indicates an action or adjustment of the right
channel.
MUTE - Indicates you are in the mute menu or the mute
function is active.

Specyfikacje produktu

Marka: Kicker
Kategoria: Radia samochodowe
Model: sx 700 4

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Kicker sx 700 4, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Radia samochodowe Kicker

Kicker

Kicker KX300.4 Instrukcja

4 Października 2024
Kicker

Kicker IX 1302 Instrukcja

1 Października 2024
Kicker

Kicker KX100.2 Instrukcja

29 Września 2024
Kicker

Kicker X50 Instrukcja

25 Września 2024
Kicker

Kicker zx 350 2 Instrukcja

24 Września 2024
Kicker

Kicker KX 400.4 Instrukcja

24 Września 2024
Kicker

Kicker ZX 300.1 Instrukcja

23 Września 2024
Kicker

Kicker kx 600 1 Instrukcja

23 Września 2024
Kicker

Kicker zr 120 Instrukcja

23 Września 2024
Kicker

Kicker KX 800.4 Instrukcja

23 Września 2024

Instrukcje Radia samochodowe

Najnowsze instrukcje dla Radia samochodowe

JVC

JVC KD-R90BT Instrukcja

15 Października 2024
Kenwood

Kenwood KMM-X705 Instrukcja

15 Października 2024
Alpine

Alpine CDM-7870R Instrukcja

14 Października 2024
Hyundai

Hyundai H-CMD2009 Instrukcja

14 Października 2024
Dual

Dual XC4100 Instrukcja

13 Października 2024
Audiovox

Audiovox VXE 3010 Instrukcja

13 Października 2024
MB Quart

MB Quart PAB 5400 Instrukcja

13 Października 2024
Hyundai

Hyundai H-CDM8023 Instrukcja

13 Października 2024
Caliber

Caliber RCD110B Instrukcja

13 Października 2024
JVC

JVC KD-X30 Instrukcja

13 Października 2024