Instrukcja obsługi Kicker KXMA1200.1

Kicker odbiornik KXMA1200.1

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kicker KXMA1200.1 (14 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/14
KXMA1200.1
Manual del Propietario | Español
AMPLIFICADOR DEL LA SERIE KXM.1
Benutzerhandbuch | Deutsch
MONOVERSTÄRKER DER KXM.1-SERIE
Manuel d’utilisation | Française
AMPLIFICATEUR DE SÉRIE KXM.1
KXM
AMPLIFIERS
Owner’s Manual
2
KXM.1-SERIES AMPLIFIERS
OWNER’S MANUAL
INSTALLATION
Mounting: Choose a dry, structurally sound location to mount your KICKER ampli er. Make sure there
are no items behind the area where the screws will be driven. Choose a location that allows at least 4
(10cm) of open ventilation for the ampli er. Drill four holes using a 7/64 (3mm) bit and use the supplied
#8 screws to mount the ampli er.
Wiring: The KXM ampli ers RCA inputs will receive either high or low level signals from your car stereo’s
source unit. A high-level signal can be run from the source units speaker outputs to the stereo RCA
input on the end panel of the amplifi er using the KICKER KISL as shown. Alternatively, the signal can be
delivered to the ampli er using the low-level RCA outputs on the source unit. Keep the audio signal cable
away from factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a
90 degree angle.
PERFORMANCE
MODEL: KXMA1200.1
IMPORTANT SAFETY WARNING
PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR SUBWOOFER IN A DISTORTED, CLIPPED
OR OVER-POWERED MANNER CAN CAUSE YOUR AUDIO SYSTEM TO OVERHEAT, POSSIBLY CATCHING FIRE
AND RESULTING IN SERIOUS DAMAGE TO YOUR COMPONENTS AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO
4 INCHES (10CM) OPEN VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT LEAST 1 INCH (2.5CM)
CLEARANCE BETWEEN THE FRONT OF THE SPEAKER AND ANY SURFACE.
NOTE: 2017 KXM amplifi er subwoofer channels are stable - power rating equivalent to operation, +/- 10%
Model: KXMA1200.1
RMS Power
@ 14.4V, 4Ω mono, 1% THD+N
@ 14.4V, 2Ω mono, 1% THD+N
600W x 1
1200W x 1
Length [in, cm] 9-9/16,24.4
Height [in, cm] 2 1/8, 5.5
Width [in, cm] 8 5/16, 21
Frequency Response ± 1dB 10Hz–160Hz
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity 250mV–10V
Selectable Electronic Crossover Variable Lo-pass 40Hz–160Hz, 24dB/octave
KickEQ+Parametric Bass Boost Boost - Variable 0–18db; Center Frequency - 20Hz–80Hz; Bandwidth 1–5
Subsonic Filter Variable 10–80Hz, 24dB/octave
3
Install a fuse within 7” (18cm) of the battery and in-line with the power cable connected to your ampli er.
source unit
high-level speaker
outputs
to ampli er
shield
+
core conductor KICKER KISL (optional)
from source unit high-
level speaker outputs
OR
to ampli er
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
KXMA1200.11 x 150 Ampere 4 Gauge PK4, CK4
12V
RADIO
DETECT
battery
external fuse
remote turn-on (see page 5)
woofer
MONO OPERATION
minimum impedance of 1 ohm
ABYC-compliant power terminals
Ampli er uses 304-stainless steel screws
and conformal coated PCB for increased
weather resistance
aluminum bottom plate
≤7”
(18cm)


Specyfikacje produktu

Marka: Kicker
Kategoria: odbiornik
Model: KXMA1200.1

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Kicker KXMA1200.1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje odbiornik Kicker

Kicker

Kicker PXA500.1 Instrukcja

6 Października 2024
Kicker

Kicker KXA400.1 Instrukcja

6 Października 2024
Kicker

Kicker IQ1000.1 Instrukcja

6 Października 2024
Kicker

Kicker 48PXA600.1 Instrukcja

22 Września 2024
Kicker

Kicker KMA600.4 Instrukcja

11 Września 2024
Kicker

Kicker CST20 Instrukcja

8 Września 2024
Kicker

Kicker KMA450.6 Instrukcja

31 Sierpnia 2024
Kicker

Kicker KXMA1200.2 Instrukcja

30 Sierpnia 2024
Kicker

Kicker IQ500.2 Instrukcja

30 Sierpnia 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik