Instrukcja obsługi Kicker CX600.1


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kicker CX600.1 (28 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/28
Owner’s Manual |
Manual del Propietario |
Benutzerhandbuch |
Manuel d’utilisation |
CX Amplifiers
2012 CX Mono Amps Rev I.indd 1
2012 CX Mono Amps Rev I.indd 1
2012 CX Mono Amps Rev I.indd 1
2012 CX Mono Amps Rev I.indd 12012 CX Mono Amps Rev I.indd 1 6/22/2012 2:32:04 PM
6/22/2012 2:32:04 PM
6/22/2012 2:32:04 PM
6/22/2012 2:32:04 PM6/22/2012 2:32:04 PM
2
CX.1-SERIES AMPLIFIERS
OWNER’S MANUAL
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open
ventilation for the amplifi er. If possible, mount the ampli er in the climate-controlled passenger compartment. Drill
four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er.
The KICKER CX Amplifi ers are capable of space-saving vertical mounting. Use a 2.5mm hex key (Allen wrench)
to loosen the endpanel, remove the existing brackets, then insert and tighten the double-slotted brackets to the
amplifi er as illustrated on the next page.
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
Model: CX300.1 CX600.1 CX1200.1
RMS Power
@ 14.4V, 4 1% THD+NΩ mono,
@ 14.4V, 2 mono, 1% THD+NΩ
150W x 1
300W x 1
300W x 1
600W x 1
600W x 1
1200W x 1
Length | in [mm] 8-1/8 [210] 8-1/8 [210] 12-1/16 [310]
Speci cations common to all models:
Height | in [mm] 2-3/8 [60]
Width | in [mm] 7-3/16 [180]
Frequency Response ± 1dB 25Hz–200Hz
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mV–5V
High Level: 250mV–10V
Electronic Crossover Variable Lo-pass 50Hz–200Hz, 12dB/octave
Bass Boost Variable 0–12dB @ 40Hz
Subsonic Filter 25Hz, 24dB/octave
Remote Bass Yes [sold separately]
Pro Tip: To get the best performance from your new KICKER Ampli er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
MODEL: CX300.1 / CX600.1 / CX1200.1
2012 CX Mono Amps Rev I.indd 2
2012 CX Mono Amps Rev I.indd 2
2012 CX Mono Amps Rev I.indd 2
2012 CX Mono Amps Rev I.indd 22012 CX Mono Amps Rev I.indd 2 6/22/2012 2:32:28 PM
6/22/2012 2:32:28 PM
6/22/2012 2:32:28 PM
6/22/2012 2:32:28 PM6/22/2012 2:32:28 PM
3
Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the
amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the
batterys negative post and the vehicle chassis is recommended.
The CX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereos source unit. A high-level signal can be run from the source unit’s speaker outputs to the
stereo RCA input on the end panel of the amplifi er using the KICKER ZISL as shown (make sure you set the CX
amplifi ers input level switch to “HI”). Alternatively, the signal can be delivered to the amplifi er using the low-level
RCA outputs on the source unit. Set the input level switch on the end panel of the ampli er to “LO”. Either input
method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to
another ampli er or component. Keep the audio signal cable away from factory wiring harnesses and other
power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to amplifi er
shield
double-slotted
bracket
+
+
+
core conductor KICKER ZISL (optional)
source unit high-level
speaker outputs
OR to amplifi er
VERTICAL MOUNTING
hex screws
amplifi er side panel
2012 CX Mono Amps Rev I.indd 3
2012 CX Mono Amps Rev I.indd 3
2012 CX Mono Amps Rev I.indd 3
2012 CX Mono Amps Rev I.indd 32012 CX Mono Amps Rev I.indd 3 6/22/2012 2:32:29 PM
6/22/2012 2:32:29 PM
6/22/2012 2:32:29 PM
6/22/2012 2:32:29 PM6/22/2012 2:32:29 PM


Specyfikacje produktu

Marka: Kicker
Kategoria: Radia samochodowe
Model: CX600.1

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Kicker CX600.1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Radia samochodowe Kicker

Kicker

Kicker KX300.4 Instrukcja

4 Października 2024
Kicker

Kicker IX 1302 Instrukcja

1 Października 2024
Kicker

Kicker KX100.2 Instrukcja

29 Września 2024
Kicker

Kicker X50 Instrukcja

25 Września 2024
Kicker

Kicker zx 350 2 Instrukcja

24 Września 2024
Kicker

Kicker KX 400.4 Instrukcja

24 Września 2024
Kicker

Kicker ZX 300.1 Instrukcja

23 Września 2024
Kicker

Kicker kx 600 1 Instrukcja

23 Września 2024
Kicker

Kicker zr 120 Instrukcja

23 Września 2024
Kicker

Kicker KX 800.4 Instrukcja

23 Września 2024

Instrukcje Radia samochodowe

Najnowsze instrukcje dla Radia samochodowe