Instrukcja obsługi Kicker BX360.4

Kicker Receiver BX360.4

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kicker BX360.4 (16 stron) w kategorii Receiver. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/16
BX AMPLIFIER
BX360.4
BX500.4
English Version
Deutsche Version
BX
2BX AMPLIFIERS
BX.4-SERIES AMPLIFIERS Owner’s Manual
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
Model: BX360.4 BX500.4
RMS Power, all channels driven
@ 14.4V, 4 stereo, ≤ 1% THD+NΩ
@ 14.4V, 2 stereo, ≤ 1% THD+NΩ
@ 14.4V, 4 mono, ≤ 1% THD+NΩ
60W x 4
90W x 4
180W x 2
80W x 4
125W x 4
250W x 2
Length 335mm 370mm
Specifications common to all models:
Height 54mm
Width 220mm
Frequency Response ± 1dB 5Hz–60000Hz
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level:
200mV–4V
High Level:
500mV–10V
Selectable Electronic Crossover OFF (bypass) - variable HP, LP | 50–200Hz, 12dB/octave
Bass Boost Variable | 0–12dB @ 40Hz
MODEL: BX360.4 / BX500.4
3
BX AMPLIFIERS
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifier. Avoid any damage of the
vehicle’s components like wires, cables, board computer, seat belts, gastank where the screws be driven.
Ensure that this chosen location provide sufficient air circulation for the amplifier. Do not mount the device into
small or sealed spaces without air circulation near by heat dispersing parts or electrical parts of the vehicle. Do
not mount the amplifier on top of a subwooferbox or any other vibrating parts, thereby parts in the inside of the
amplifier may get loosen. Drill four holes using a 3mm bit and use the supplied screws to mount the amplifier.
Wiring: Disconnect the ground connection of vehicle’s battery to avoid an electrical short. Then, connect the
ground wire to the amplifier. Connect the GROUND terminal with a suitable contact ground point on the vehicle’s
chassis. The ground wire must be as short as possible and must be connected to a blank metallic point at the
vehicle’s chassis. Ensure that this ground point has a stable and safe electric connection to the negative “–”pole
of the battery. Check this ground wire from the battery to the ground point if possible and enforce it, if required.
Adding an additional ground wire of a larger gauge between the battery’s negative post and the vehicle chassis is
recommended.
12V
battery
external fuse
BX360.4 50 A
BX500.4 60 A
remote turn-on
from source unit
bare-metal
chassis ground
30cm
60cm
Install a fuse within 30cm of the battery and in-line with the power cable connected to your amplifier. If you ever
need to remove the amplifier from the vehicle after it has been installed, the ground wire should be the last wire
disconnected from the amplifier-just the opposite as when you installed it.
AMP 2
AMP 1
The BX amplifier has two input sections.
The RCA inputs can process the low
level signals from your car stereos
source unit. The HI LEVEL INPUT is
suitable to connect loudspeaker wires
of your headunit, if your headunit is not
equipped with preamplifier RCA outputs.
Keep the audio signal cable away from
factory wiring harnesses and other power
wiring if possible. If you need to cross
this wiring, cross it at a 90 degree angle
if possible.
WARNING: Never use the RCA inputs and the HI LEVEL INPUTS at the same time.
Connect the loudspeaker wires of your vehicle according to the drawing above with the included HI LEVEL
INPUT jack. The ground wire (black) must be connected with the ground of vehicle’s chassis.
Then, plug-in the HI LEVEL INPUT jack into the HI LEVEL INPUT socket.

Specyfikacje produktu

Marka: Kicker
Kategoria: Receiver
Model: BX360.4

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Kicker BX360.4, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Receiver Kicker

Instrukcje Receiver

Najnowsze instrukcje dla Receiver

FiveO

FiveO LIBRA 1200 Instrukcja

22 Września 2024
LEA

LEA Connect 704 Instrukcja

22 Września 2024
Brigmton

Brigmton BTDT2-918 Instrukcja

21 Września 2024
Audizio

Audizio AD220A Instrukcja

21 Września 2024
Skytronic

Skytronic AV-360 Instrukcja

21 Września 2024
HQ Power

HQ Power SAIGOR 100 Instrukcja

21 Września 2024
Phonic

Phonic XP 3100 Instrukcja

21 Września 2024
DAP-Audio

DAP-Audio DSA-250 Instrukcja

21 Września 2024
JETI

JETI JDEX-R5L Instrukcja

21 Września 2024