Instrukcja obsługi Kicker 48KXMA900.5

Kicker odbiornik 48KXMA900.5

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kicker 48KXMA900.5 (15 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/15
KXMA900.5
Manual del Propietario | Español
AMPLIFICADOR DEL LA SERIE KXM.5
Benutzerhandbuch | Deutsch
VERSTÄRKER DER KXM.5-SERIE
Manuel d’utilisation | Française
AMPLIFICATEUR DE SÉRIE KXM.5
KXM
AMPLIFIERS
Owner’s Manual
2
KXMA.5-SERIES AMPLIFIERS
OWNER’S MANUAL
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER ampli er. Make sure there are no
items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of
open ventilation for the amplifi er. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws
to mount the ampli er.
PERFORMANCE
MODEL: KXMA900.5
IMPORTANT SAFETY WARNING
PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR SUBWOOFER IN
A DISTORTED, CLIPPED OR OVER-POWERED MANNER CAN CAUSE YOUR AUDIO SYSTEM
TO OVERHEAT, POSSIBLY CATCHING FIRE AND RESULTING IN SERIOUS DAMAGE TO YOUR
COMPONENTS AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO 4 INCHES (10CM) OPEN
VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT LEAST 1 INCH (2.5CM)
CLEARANCE BETWEEN THE FRONT OF THE SPEAKER AND ANY SURFACE.
Model: KXMA900.5
RMS Power, and AMP1 AMP2
@ 14.4V, stereo, ≤ 1% THD+N
@ 14.4V, stereo, ≤ 1% THD+N
@ 14.4V, bridged mono, ≤ 1% THD+N
75W x 4
125W x 4
250W x 2
RMS Power, channelSUB
@ 14.4V, mono, ≤ 1.5 % THD+N
@ 14.4V, mono, ≤ 1.5 % THD+N
@ 14.4V, mono, ≤ 1.5 % THD+N
400W x 1
400W x 1
200W x 1
Length [in, cm] 12-3/4, 32.4
Height [in, cm] 2-1/8, 5.5
Width [in, cm] 8-5/16, 21
Frequency Response [Hz] 10Hz–20kHzAMPS 1-2:
SUB: 20Hz–160Hz
Signal-to-Noise Ratio [dB]
1W Signal-to-Noise Ratio [dB]
>95dB, A-weighted, re: rated power
-75dB
Input Sensitivity Low 125mV – 5V
Hi 250mV – 10V
Selectable Electronic Crossover OFF/HP/LP, variable 10–5,000Hz with 10X AMP 1:
switch; 24dB/octave
AMP 2: OFF/HP/LP/BP, variable HP 10–500Hz,
variable LP 40–5,000Hz with 10X switch; 24dB/octave
SUB: Variable LP 40–160Hz; 24dB/octave
KickEQ™ Parametric Bass Boost Boost - Variable 0-6db; Center Frequency - 40Hz
Subsonic Filter Variable 10–80Hz; 24dB/Octave (sub channel only)
3
Install a fuse within 7” (18cm) of the battery and in-line with the power cable connected to your ampli er.
POWER WIRING
source unit
high-level speaker
outputs
to ampli er
shield
+
core conductor KICKER KISL (optional)
from source unit high-
level speaker outputs
OR
to ampli er
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
KXMA900.5 1 x 100 Ampere 4 Gauge KMPK4, PK4, CK4
REMOTE BASS
12V
Wiring: The KXMA ampli er’s RCA inputs will receive either high or low level signals from your car stereos
source unit. A high-level signal can be run from the source unit’s speaker outputs to the stereo RCA
input on the end panel of the amplifi er using the KICKER KISL as shown. Alternatively, the signal can be
delivered to the amplifi er using the low-level RCA outputs on the source unit. Keep the audio signal cable
away from factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a
90 degree angle.
battery
external fuse
remote turn-on (see page 6)
ABYC-compliant power terminals Ampli er uses 304-stainless steel screws
and conformal coated PCB for increased
weather resistance
aluminum bottom plate
≤7
(18cm)


Specyfikacje produktu

Marka: Kicker
Kategoria: odbiornik
Model: 48KXMA900.5

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Kicker 48KXMA900.5, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje odbiornik Kicker

Kicker

Kicker PXA500.1 Instrukcja

6 Października 2024
Kicker

Kicker KXA400.1 Instrukcja

6 Października 2024
Kicker

Kicker IQ1000.1 Instrukcja

6 Października 2024
Kicker

Kicker 48PXA600.1 Instrukcja

22 Września 2024
Kicker

Kicker KMA600.4 Instrukcja

11 Września 2024
Kicker

Kicker CST20 Instrukcja

8 Września 2024
Kicker

Kicker KMA450.6 Instrukcja

31 Sierpnia 2024
Kicker

Kicker KXMA1200.2 Instrukcja

30 Sierpnia 2024
Kicker

Kicker IQ500.2 Instrukcja

30 Sierpnia 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik