Instrukcja obsługi Juki SC-922

Juki maszyna do szycia SC-922

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Juki SC-922 (61 stron) w kategorii maszyna do szycia. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/61

SC-922

InStruCtIon Manual

CONTENTS

I. SPECIFICATIONS ........................................................................................ 1

II. SET-UP ........................................................................................................ 1

1. Installing to the table ..........................................................................................................................1

2. Installing the motor unit .....................................................................................................................2

3. Installing the control box ...................................................................................................................2

4. Installing the belt ................................................................................................................................3

5. Adjusting the pulley cover .................................................................................................................3

6. Installation and adjustment for the protecting pin and the belt slip-off preventing bracket .......4

7. Connecting the cords .........................................................................................................................5

8. Attaching the connecting rod .......................................................................................................... 13

9. Setting procedure of the machine head ......................................................................................... 14

10. Adjusting the machine head (direct-drive motor type sewing machine only) ............................ 15

III. FOR THE OPERATOR ............................................................................. 16

1. Operating procedure of the sewing machine .................................................................................16

2. Operation panel (CP-18) ...................................................................................................................17

3. Operating procedure of the sewing pattern ...................................................................................18

(1) Reverse feed stitching pattern ......................................................................................................18

(2) Overlapped stitching pattern .........................................................................................................19

4. One-touch setting .............................................................................................................................20

5. Production support function ........................................................................................................... 22

6. Setting of functions of SC-922 ........................................................................................................25

7. Function setting list ..........................................................................................................................27

8. Detailed explanation of selection of functions .............................................................................. 33

9. Automatic compensation of neutral point of the pedal sensor ...................................................47

10.Selectionofthepedalspecications ..............................................................................................47

11.

Stitch alignment for the reverse stitching at the end of sewing (for heavy-weight materials)

... 48

12. Input/output function of the hand switch and knee switch ..........................................................49

13. Use of the hand switch and the knee switch ..................................................................................50

14. Setting of the auto lifter function ....................................................................................................51

15. Selecting procedure of the key-lock function ................................................................................52

16. Initialization of the setting data .......................................................................................................52

17. External input / output connector ...................................................................................................53

18. How to connect the material edge sensor ......................................................................................54

IV. MAINTENANCE ....................................................................................... 55

1. Removing the rear cover ..................................................................................................................55

2. Replacing the fuse ............................................................................................................................ 55

3. Error codes ........................................................................................................................................56

– 1 –

I. SPECIFICATIONS

Supply voltage Single phase 100 to 120V 3-phase 200 to 240V Single phase 220 to 240V

Frequency 50Hz/60Hz 50Hz/60Hz 50Hz/60Hz

Operating envi-

ronment

Temperature : 0 to 40˚C

Humidity : 90% or less

Temperature : 0 to 40˚C

Humidity : 90% or less

Temperature : 0 to 40˚C

Humidity : 90% or less

Input 310VA 310VA 310VA

* The electric power is a reference value for the model equipped with the LU-1510N-7 machine head.

It differs by the selected machine head.

II. SET-UP

The SC-922 can be used with the direct-motor type machine head as a stand-alone control box. It can also

be used with the belt-driven type machine head by installing on the motor unit.

This manual describes the procedure for the aforementioned two setup methods.

This describes the procedure for installing the

SC-922 on the table of the LU-2810-7 sewing ma-

chine. To use any other machine head, install the

control box on the table referring to the Instruction

Manual for the main body of the relevant sewing ma-

chine. Install the control box suspending plate on the

table with mounting bolts supplied with the unit. At

this time, insert the nuts and washers supplied with

the unit as accessories as shown in the gure so that

the motor unit can be securely xed on the table.

1) Press three bolts 1 supplied with the unit as ac-

cessories into the motor hanging bolt hole in the

table and x them.

2) Fix suspending plate 5 supplied with the unit

on the three bolts with plain washer 2, spring

washer 3 and nut 4.

3) Fix rubber 6 on the suspending plate with spring

washer 7 and nut 8.

4) Hang one end of the control box on the threaded

part of rubber on the side which has two bolts.

Then, hang the other end of the control box on

the opposite side.

5) Temporarily x the other threaded part of rubber

with plain washer 9 and nut !0. In this case, the

spring washer is not used.

6) Adjusting the installing position of the control box.

Then, securely tighten the nuts.

1. Installing to the table

To use the SC-922 with the direct-motor type machine head, install the control box on the table according to

the following instruction.

Specyfikacje produktu

Marka:	Juki
Kategoria:	maszyna do szycia
Model:	SC-922

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Juki SC-922, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje maszyna do szycia Juki

Juki MS-1190 Instrukcja

12 Stycznia 2025

Juki LK-1903BN Instrukcja

30 Grudnia 2025

Juki MH-380 Instrukcja

30 Grudnia 2025

Juki MH-382 Instrukcja

30 Grudnia 2025

Juki LU-1509N Instrukcja

14 Października 2024

Juki HZL-30Z Instrukcja

5 Października 2024

Juki LU2-4410-B1T-CS Instrukcja

3 Października 2024

Juki DSC-244 Instrukcja

1 Października 2024

Juki LU-2210 Instrukcja

30 Września 2024

Juki AW-3SD Instrukcja

30 Września 2024

Instrukcje maszyna do szycia

Najnowsze instrukcje dla maszyna do szycia

Pfaff 463H Instrukcja

15 Stycznia 2025

Elna Lotus ZZ Instrukcja

14 Stycznia 2025

Brother Aveneer EV1-LE Instrukcja

14 Stycznia 2025

Brother Aveneer EV1 Instrukcja

14 Stycznia 2025

Necchi Maximatic 586 Instrukcja

12 Stycznia 2025

Pfaff 295-1 Instrukcja

12 Stycznia 2025

Brother Innov-is NV-180 Instrukcja

12 Stycznia 2025

Baby Lock Imagine 2 Instrukcja

12 Stycznia 2025

Alfa 1412 Instrukcja

11 Stycznia 2025

Baby Lock Ellure - BLR Instrukcja

11 Stycznia 2025