Instrukcja obsługi Juki MF-7900D

Juki maszyna do szycia MF-7900D

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Juki MF-7900D (22 stron) w kategorii maszyna do szycia. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/22

INSTRUCTION MANUAL

MF-7900(D)/UT55,56,57

CONTENTS

I. SPECIFICATIONS ...........................................................................................................1

II. AT THE BEGINNING......................................................................................................1

III. INSTALLING THE ACCESSORIES.............................................................................2

1. Installing the presser lifting cylinder 2 ............................................................................................

2. Installing the air regulator 2 ..............................................................................................................

3. Installation and setting SC-921 3 ......................................................................................................

(1) Installing the SC-921 on the table ( Table-mount type ) 3 ............................................................................

(2) Installing the SC-921 on the table ( Semi-submerged type ) 3 ....................................................................

(3) Connecting the cords 4 ...................................................................................................................................

(4) Setting procedure of the machine head 5 .....................................................................................................

(5) Setting the lower stop position of the needle bar 6 .....................................................................................

IV. AIR PIPING DRAWING.................................................................................................7

1. Piping of the thread trimmer device (UT57) 7 ..................................................................................

2. Piping of the thread trimmer device (UT55) 8 ..................................................................................

3. Piping drawing for air blow (UT56) 9 ................................................................................................

4. Adjusting the air regulator 9 .............................................................................................................

V. THREADING THE MACHINE HEAD ..........................................................................10

VI. ADJUSTING THE LOOPER THREAD TRIMMER MECHANISM ...........................11

1. Adjusting the thread trimmer air cylinder ....................................................................................11

2. Adjusting the Lower knife 12 ............................................................................................................

3. Adjusting the position of clamp pressure adjusting spring 12 .....................................................

4. Adjusting the knife engagement and the knife pressure adjusting spring 12 .............................

5. Adjusting the pressure of clamp spring 12 .....................................................................................

6. Initial position of the looper thread trimmer mechanism 13 ..........................................................

7. Adjusting the stopper 13 ...................................................................................................................

8. Adjusting the height of the lower knife 13 .......................................................................................

9. Adjusting the lower knife holder guide 13 .......................................................................................

10. Adjusting the longitudinal position of the blade point of lower knife 14 ......................................

11. Adjusting the thread trimmer sensor 14 ..........................................................................................

12. Adjusting the speed of looper thread trimmer 14 ...........................................................................

VII. ADJUSTING THE THREAD RELEASE MECHANISM ..........................................15

1. Adjusting the disk-rise 15 .................................................................................................................

2. Adjusting the thread release hook 15 ..............................................................................................

VIII. ADJUSTING THE TOP COVERING THREAD TRIMMER MECHANISM ............16

1. Adjusting the engagement of knives 16 ..........................................................................................

2. Adjusting the pressure of clamp spring 16 .....................................................................................

3. Adjusting the position of the blade point of moving knife 16 ........................................................

4. Adjusting the speed of moving knife 17 ..........................................................................................

IX. ADJUSTING THE AIR-BLOW WIPER (UT56) .........................................................18

1. Installing the air-blow wiper 18 .........................................................................................................

2. Adjusting the air-blow wiper 18 ........................................................................................................

X. ADJUSTING THE NEEDLE THREAD WIPER (UT55) ..............................................19

1. Adjusting the clamp spring 19 ..........................................................................................................

2. Installing the needle thread wiper 19 ...............................................................................................

XI. MAINTENANCE ..........................................................................................................20

1. Cleaning the motor fan 20 .................................................................................................................

– 1 –

I. SPECIFICATIONS

Model name High-speed, cylinder-bed coverstitch machine Semi-dry head, high-speed, cylinder-bed

coverstitch machine

Model MF-7900 series MF-7900D series

Stitch type ISO standard 406, 407, 602, and 605

Example of application

Hemming and covering for knits and general knitted fabrics

Sewing speed Max. 6,500 sti/min (at the time of intermittent operation)

V-belt type

Max. 6,000 sti/min (at the time of intermittent operation)

Direct-drive type

Speed of stitch at the delivery:

4,500 sti/min (at the time of intermittent operation)

Max. 5,000 sti/min (at the time of intermittent operation)

V-belt type

Max. 5,000 sti/min (at the time of intermittent operation)

Direct-drive type

Speed of stitch at the delivery:

4,000 sti/min (at the time of intermittent operation)

Needle gauge 5.6 mm and 6.4 mm 3-needle .....

2-needle ..... 3.2 mm, 4.0 mm and 4.8 mm

Di󰀨erential feed ratio 1 : 0.9 to 1 : 1.8 (stitch length : less than 2.5 mm)

(1 : 0.6 to 1 :1 .1, when the di󰀨erential link hinge screw is changed)

Micro-di󰀨erential feed adjustment mechanism is provided. (Micro-adjustment)

Stitch length 0.9 mm to 3.6 mm (can be adjusted up to 4.5 mm)

Needle UY128GAS #9S to #14S (standard #10S) UY128GAS #9S to #12S (standard #10S)

Needle bar stroke 31mm (33 mm when the eccentric pin is changed over)

Dimensions (Height) 450 x (Width) 456 x (Length) 299

Weight 45 kg (With pneumatic type thread trimmer) , 42 kg

Lift of presser foot 8 mm (needle gauge : 5.6 mm without top covering), and 5 mm (with top covering)

Micro-lifter mechanism is provided.

Feed adjustment

method

Main feed ............... dial type stitch pitch adjustment method

Di󰀨erential feed lever adjustment method (micro-adjustment mechanism is provided.) .....

Looper mechanism Spherical rod drive method

Lubricating system Forced lubrication method by gear pump

Lubricating oil JUKI GENUINE OIL 18

Oil reservoir capacity Oil gauge lower line : 600 cc to upper line : 900 cc

Installation Table-mount type, Semi-submerged type

Noise - Equivalent continuous emission sound pressure level

(LpA) at the workstation:

A-weighted value of 79.5 dB; (Includes K

pA = 2.5 dB);

according to ISO 10821- C.6.2 -ISO 11204 GR2 at

4,500 sti/min.

- Equivalent continuous emission sound pressure level

(LpA) at the workstation:

A-weighted value of 76.5 dB; (Includes K

pA = 2.5 dB);

according to ISO 10821- C.6.2 -ISO 11204 GR2 at

4,000 sti/min.

Remove xed band ❶ for transportation before setting

up the sewing machine.

II. AT THE BEGINNING

❶

Specyfikacje produktu

Marka:	Juki
Kategoria:	maszyna do szycia
Model:	MF-7900D

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Juki MF-7900D, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje maszyna do szycia Juki

Juki MS-1190 Instrukcja

12 Stycznia 2025

Juki LK-1903BN Instrukcja

30 Grudnia 2025

Juki MH-380 Instrukcja

30 Grudnia 2025

Juki MH-382 Instrukcja

30 Grudnia 2025

Juki LU-1509N Instrukcja

14 Października 2024

Juki HZL-30Z Instrukcja

5 Października 2024

Juki LU2-4410-B1T-CS Instrukcja

3 Października 2024

Juki DSC-244 Instrukcja

1 Października 2024

Juki LU-2210 Instrukcja

30 Września 2024

Juki AW-3SD Instrukcja

30 Września 2024

Instrukcje maszyna do szycia

Najnowsze instrukcje dla maszyna do szycia

Pfaff 463H Instrukcja

15 Stycznia 2025

Elna Lotus ZZ Instrukcja

14 Stycznia 2025

Brother Aveneer EV1-LE Instrukcja

14 Stycznia 2025

Brother Aveneer EV1 Instrukcja

14 Stycznia 2025

Necchi Maximatic 586 Instrukcja

12 Stycznia 2025

Pfaff 295-1 Instrukcja

12 Stycznia 2025

Brother Innov-is NV-180 Instrukcja

12 Stycznia 2025

Baby Lock Imagine 2 Instrukcja

12 Stycznia 2025

Alfa 1412 Instrukcja

11 Stycznia 2025

Baby Lock Ellure - BLR Instrukcja

11 Stycznia 2025