Instrukcja obsługi Juki AW-3S

Juki maszyna do szycia AW-3S

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Juki AW-3S (47 stron) w kategorii maszyna do szycia. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/47

INSTRUCTION MANUAL

AW-3S

CONTENTS

1. GENERAL ............................................................................................... 1

1-1. Specications of AW-3....................................................................................................... 1

1-2. Conguration...................................................................................................................... 2

2. INSTALLATION 4 .......................................................................................

2-1. Installing the AW-3S ........................................................................................................... 4

2-2. Installation location ........................................................................................................... 4

2-3. Installing the bobbin thread remaining amount detection sensor (optional) ............... 4

3. OPERATION PROCEDURE 5 ...................................................................

3-1. 5Opening/closing the cover door .......................................................................................

3-2. How to thread the device with the bobbin thread ........................................................... 6

3-3. How to set a bobbin ........................................................................................................... 8

3-4. Length of remaining thread to be removed ................................................................... 11

3-5. Device operation lamp ..................................................................................................... 12

3-6. To use the AW-3 ................................................................................................................ 13

3-7. Behavior of the AW-3 device when the power is turned ON ........................................ 14

3-8. ................................................................................................... 15Memory switch data list

3-9. Basic operation and setting ............................................................................................ 16

3-10. Operating the AW ........................................................................................................... 17

3-11. Setting the AW number-of-stitches input mode, AW operation mode and

remaining-thread allowance length ................................................................................ 20

3-12. Example of operation..................................................................................................... 27

3-13. Turning OFF of the power ............................................................................................. 32

3-14. Error display and error handling procedure................................................................ 32

3-15. Detection of errors related to the AW ........................................................................... 34

3-15. List of errors ................................................................................................................... 36

4. MAINTENANCE 38 ....................................................................................

4-1. Attaching / removing the cover ...................................................................................... 38

4-2. Cleaning ............................................................................................................................ 39

4-3. Replacing the fuse ........................................................................................................... 41

4-4. Replacing the gripper tube.............................................................................................. 41

4-5. Corrective measure against idling of the bobbin.......................................................... 42

4-6. Adjusting the air ow for the remaining thread guide ................................................. 42

4-7. Attaching/removing the AW main body ......................................................................... 43

5. TROUBLESHOOTING 44 ..........................................................................

– 1 –

1. GENERAL

1 Applicable bobbin, bobbin

case

Exclusive double-capacity bobbin and bobbin case.

2 Applicable thread count #5 to #30 (Japan), 135 to 45 (TEX), 020 to 060 (TKT)

3 Applicable type of thread Synthetic thread

4 Remaining-thread removal and

bobbin winding operation

Possible while the sewing machine is in operation.

5 Condition setting according

to the thread type

Conditions to be met to unravel the thread at the beginning of

winding a bobbin can be set.

6 100,120/200,220,240 Vac ±10 %, Single phase 50/60 HzLine voltage

7 Power consumption 100 VA

8 Air pressure used 0.5 to 0.55 MPa

9 Air consumption 156 Nℓ / min (max. value)

10 Dimensions

700 mm (W

)

× 650 mm (L

)

× 430 mm

) (Accessories includ-

ed)

11 Mass of the device 38 kg

Operating temperature range

5 ˚C to 35 ˚C

Operating humidity range

35 % to 85 % (No dew condensation)

14 - Equivalent continuous emission sound pressure level (LNoise pA) at

the workstation : A-weighted value

≦ 75 dB ; (Includes KpA =

2.5 dB) ; according to ISO 10821- C.6.2 -ISO 11204 GR2 at

remaining-thread removal length = 2 m; Bobbin-thread winding

length (22 m).

Conventionally, a series of operations including the replacement of a bobbin in the sewing machine

hook, removal of thread remaining on a bobbin, winding of a bobbin, threading of the bobbin case ten-

sion spring and trimming of thread have been carried out manually. Now, this device has been devel-

oped to carry out the series of operations full-automatically. This device not only helps increase e󰀩cien-

cy of sewing work but also ensures stable product making in such processes that require high seam

quality.

Refer to the Instruction Manual for the AMS-221EN/AMS224EN/IP-420 for information about the main

body of the sewing machine.

1-1. Specications of AW-3

Specyfikacje produktu

Marka:	Juki
Kategoria:	maszyna do szycia
Model:	AW-3S

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Juki AW-3S, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje maszyna do szycia Juki

Juki MS-1190 Instrukcja

12 Stycznia 2025

Juki LK-1903BN Instrukcja

30 Grudnia 2025

Juki MH-380 Instrukcja

30 Grudnia 2025

Juki MH-382 Instrukcja

30 Grudnia 2025

Juki LU-1509N Instrukcja

14 Października 2024

Juki HZL-30Z Instrukcja

5 Października 2024

Juki LU2-4410-B1T-CS Instrukcja

3 Października 2024

Juki DSC-244 Instrukcja

1 Października 2024

Juki LU-2210 Instrukcja

30 Września 2024

Juki AW-3SD Instrukcja

30 Września 2024

Instrukcje maszyna do szycia

Najnowsze instrukcje dla maszyna do szycia

Husqvarna Prelude 370 Instrukcja

8 Kwietnia 2025

Janome Mystical Mint Instrukcja

5 Marca 2025

Dürkopp Adler 1265-7 Instrukcja

4 Marca 2025

Brother Innov-is 15P Instrukcja

1 Marca 2025

Janome 41012 Instrukcja

24 Lutego 2025

Janome Fast Lane Fucshia Instrukcja

24 Lutego 2025

Janome Blue Couture Instrukcja

24 Lutego 2025

Janome Horizon 7700 Instrukcja

24 Lutego 2025

Husqvarna-Viking Hiclass 100Q Instrukcja

18 Lutego 2025

SilverCrest SNM 33 B2 Instrukcja

17 Lutego 2025