Instrukcja obsługi JL Audio Stealthbox SB-T-4RNR2/10W3v3/GA

JL Audio Niesklasyfikowane Stealthbox SB-T-4RNR2/10W3v3/GA

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JL Audio Stealthbox SB-T-4RNR2/10W3v3/GA (3 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

➔

Stealthbox®

I N S T A L L A T I O N G U I D E

SB - T-4RNR2/10 W v 2 , J L AU D I O , In c 2 0 0 3 Sh e e t S K U # 0 1 1 1 8 1 Re v i s io n 0 1 / 1 3 / 2 0 0 4

Pag e 1

for the

SB-T-4RNR2/10W3v2

(‘02-Up Toyota 4-Runner SR-5, Sport

Edition & Limited)

This Stealthbox is a product which

requires professional installation skills and

tools.

Please read this installation guide thor-

oughly before beginning the project. It

will guide you step by step through the

installation. Several of the steps in this

process may require two people to

accomplish.

It is absolutely vital that the enclosure

be properly mounted to the vehicle

according to these instructions. Failure

to mount the enclosure properly pres-

ents two problems: 1) The sub-bass

performance will suffer due to the

movement of the enclosure caused by

the force exerted by the woofer(s) and

2) A loose enclosure presents a serious

safety hazard in the event of a collision

or sudden deceleration.

Please enjoy your JL Audio Stealthbox

responsibly.

STEP 1:

Clean out all contents. Remove the

cargo cover and carpet mat.

STEP 2: Remove the rear sill plate(A) and side

storage door(B).

With the sill plate removed, pull and fold over the car-

pet out of the corner(circled).

On Limited Edition interiors, remove the plastic tray.

The flooring carpet will not fit flush aginst the

Stealthbox, once isntalled.

STEP 3:

Place the supplied wax square into

position.

The middle of wax square (X marks the

spot) needs to be 3.5” back from the wheel

well and from the side panel.2.5”

Remove the adhesive protective paper from

the under side of the wax square and stick to

the floor.

STEP 4: Thread in the supplied tsocket cup set

screw, leaving about a 1/2” out of the Stealthbox.

Make sure that the socket cup end is exposed.

Place the Stealthbox into position and press down

firmly.

STEP 5: With the Stealthbox removed and wax

square still in position, use a 1/2” drill bit to drill out

the marked location.

After hole is drilled, remove the wax square.

STEP 6: Place and line up the hole, of one of the

supplied black metal plates to the 1/2” drilled hole

from STEP 5.

Use tape to temporary secure the metal plate into

position.

START

HERE

Continued on Next Page ➔

w w w . j l a u d i o . c o m

➔

STEP

2.5”

3.5”

➔

➔ ➔

STEP 7: Place the carpet that was pulled out of

the corner in , back into position.STEP 2

Cut out an access hole in the carpet, that is lined up

and position above the black metal plate’s hole, from

STEP 6.

STEP 8B: When the knob is unlocked correctly,

the exposed knob will pull away from the side panel,

but is still attached to the cleat assembly.

With the cleat unlocked, remove from the side

panel.

Cont.

From

Page

Continued on Next Page ➔

➔

STEP 8: Remove the access door( ) and cargoA

net cleat(B).

Follow STEPS 8A and 8B to properly remove

the cargo net cleat.

STEP 9: Run the speaker wire to the Stealthbox’s

location.

Check for proper operation of the woofer and

attach speaker wire to terminal.

Before placing the Stealthbox back into location,

back out the threaded rod to expose about 1”.

STEP 8A: This is how the cleat looks when

installed into the side panel. (side panel not seen)

Grab a hold of the exposed knob’s edge with your

finger nails and pull out. It should not require a lot of

force. *Do not force it.*

SB - T-4 RN R2 / 1 0 W v 2 , J L AUD IO, I n c 2 0 0 3 Sh e e t S K U # 0 1 1 1 8 1 Re v i s io n 0 1 / 1 3 /2 0 0 4

Pag e 2

w w w . j l a u d i o . c o m

➔

STEP 10: With the Stealthbox wired up and in

location(with socket cup set screw placed through the car-

pet, metal plate and floor).

Place a supplied flat washer onto the supplied bolt. Place the

bolt assembly through the upper mounting support bracket

of the Stealthbox and the factory plastic side panel.

On the back side of the plastic side panel, place a supplied

flat washer, lock washer and then thread supplied nut onto

the bolt assembly .(through the removed excess door loca-

tion.)

Using a 9/16” open end wrench to hold the nut behind the

plastic panel.Tighten the exposed bolt with a 9/16” socket.

➔

Specifications:

Enclosure Type: Acoustical Suspension (Sealed)

Driver Type: 10W3v2-D2

Nominal Impedance: 4Ω

Cont. Power Handling: 300Watts

JL Audio recommends using a high quality amplifier such as the JL Audio 250/1. The diagram below shows the recommended

crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.

Supplied Hardware:

2) 3/8” Split Lock Washers

2) 3/8” Flat Washers

2) 3/8” x 1-1/4” Fender

2) 3/8”-16 x 2-1/4” hex

1) 1/4”-20 Install Bolt

1) 3/8”-16 x 2-1/4” Socket Cup Set Screw

1) 3” x 3” Wax Square

2) 3/8”-16 Hex Nut

10369 N. Commerce Pkwy, Miramar, Florida 33025-392 Phone: 954.443.1100 Fax: 954.443.1111

JL AUDIO 250/1

monoblock subwoofer amplifier

Amplifier Input Section

Input Sens.Input Voltage

Low/High

Left Ch. Right Ch.

Signal Sensing

Off/On

Output Mode

Full-Range/Low-Pass/High-Pass

Left Ch. Right Ch.

Amp LP Filter

Mode/Slope

Off/12dB/24dB

Filter Freq. (Hz)

Bass Control

LF Boost (dB)

Off/30Hz

Infrasonic Filter

+1 +13

+10

Preamp Output Section

+12VDC Ground Remote

The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for detailed information

about installing and tuning this amplifier.

➔ ➔ ➔

STEP 11: Take the other supplied black metal

plate, lock washer, flat washer and nut to the under

side of vehicle.

STEP 12: Place the other black metal support

plate, flat washer, lock washer and thread the nut

onto the threaded rod. Use a 9/16” socket and long

extension to fully secure the mounting assembly.

If the socket cup set screw is not protruding far

enough, loosen.

STEP 13: Replace the carpet and any other con-

tents back into cargo area.

For cosmetics, we folded the corner of the carpet

back under it self. We do not recommend that you

cut this carpet.

➔

SB - T- 4 RN R2 / 1 0 W v 2 , J L AU DI O, I n c 2 0 0 3 Sh e e t S K U # 0 1 1 1 8 1 Re v i s io n 0 1 / 1 3 /2 0 0 4Pag e 3

w w w . j l a u d i o . c o m

Mid/High Frequency Driver Information:

CONGRATULATIONS!

INSTALL COMPLETE.

TR690-TXI

VR650-CXI

Front Location Driver Size:

6”x9” with separated tweeter

Applicable JL Audio Products:

TR690-TXi & VR690-CXi, does require

spacer/mounting rings.

Rear Location Driver Size:

6 3/4”

Applicable JL Audio Products:

TR650-CXi,VR650-CXi & XR650-CXi,

does require spacer/mounting rings.

Cont.

From

Page

Specyfikacje produktu

Marka:	JL Audio
Kategoria:	Niesklasyfikowane
Model:	Stealthbox SB-T-4RNR2/10W3v3/GA

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JL Audio Stealthbox SB-T-4RNR2/10W3v3/GA, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane JL Audio

JL Audio MediaMaster 55-HR Instrukcja

7 Października 2024

JL Audio MediaMaster 55 Instrukcja

7 Października 2024

JL Audio Stealthbox SB-J-JL4DPAS/10TW1-2 Instrukcja

4 Października 2024

JL Audio MBT-RX Instrukcja

3 Października 2024

JL Audio MediaMaster MM105-HR Instrukcja

2 Października 2024

JL Audio JLINK RX Instrukcja

30 Września 2024

JL Audio Stealthbox SB-POL-RZG3/10TW3 Instrukcja

29 Września 2024

JL Audio Stealthbox SBA-J-JK-FHB Instrukcja

27 Września 2024

JL Audio Stealthbox SB-GM-BURBCNSL/10W3v3 Instrukcja

27 Września 2024

JL Audio Stealthbox SB-F-SUPRDTY/10W1v3 Instrukcja

27 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024