Instrukcja obsługi JL Audio Stealthbox SB-POL-RZG2/10TW3

JL Audio Niesklasyfikowane Stealthbox SB-POL-RZG2/10TW3

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JL Audio Stealthbox SB-POL-RZG2/10TW3 (3 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/3
Continued on Next Page
SB-POL-RZG2/10TW3 INSTR_SKU# 011446
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your
authorized JL Audio dealer. The installation professionals employed by your
dealer have the necessary tools and experience to disassemble and reassemble
your vehicle properly. If you prefer to perform your own installation, please read
this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely
vital that the Stealthbox® be properly mounted to the vehicle
according to these instructions. Failure to mount the enclosure
properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the
enclosure caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a
collision or sudden deceleration.
INSTALLATION
DIFFICULTY:
ESTIMATED T IME:
2 HOURS
25
OUT
OF
Enclosure Type: Sealed
Driver Type: 10TW3-D4
Nominal Impedance: 2 ohms
Continuous Power Handling: 400 watts (RMS method)
I N S T A L L A T I O N G U I D E
for the
SB-POL-RZG2/10TW3
SKU# 94620
2014-2018 Polaris RZR XP 1000, RZR XP 4 1000,
RZR 900 XC, & RZR 4 900
Page 5 • JL Audio, Inc., 2019 Continued on Next Page
S T E P 16
Carefully unclip the dash panel from around
the glove compartment, and remove panel
from the vehicle.
S T E P 15
Carefully unclip the side of the dash panel.
S T E P 14
Carefully unclip the top of the dash panel.
S T E P 13
Remove the indicated Torx bolt from the dash
panel, along with the one on the opposite side.
S T E P 12
Pictured are the dash light and USB grommet
removed from the dash panel.
S T E P 11
Remove the indicated grommet for the USB
connector from the dash panel, if equipped.
S T E P 10
Remove the indicated dash light from the dash
panel.
S T E P 9
Remove the indicated screw from the dash
panel bracket.
SB-POL-RZG2/10TW3 INSTR_SKU# 011446
Page 5 • JL Audio, Inc., 2019 Continued on Next Page
ST E P 3 2
Secure the replacement Glove Box Latch
bracket to the back of the glove compartment
as shown using the factory bolt removed in the
previous step.
S T E P 31
Remove the factory bolt holding the latch
bracket to the back of the glove compartment
door, and remove the bracket.
ST E P 3 0
Secure the glove compartment door latch to
the enclosure using the included #8 x 1/2” Pan
Head Screws.
ST E P 2 9
Remove the two factory screws holding the
glove compartment door latch to the glove
compartment, and remove the latch. These
factory screws will not be reused.
ST E P 28
Reinstall the dash light and USB connector, if
equipped, to the dash panel. Route the
speaker cable as necessary.
S T E P 27
Secure the Side Bracket to the dash panel using
the factory screw removed in Step 9.
S TE P 2 6
Reinstall the dash panel.
ST E P 2 5
Check the Stealthbox® alignment using the
dash panel, make adjustments as necessary,
and fully tighten all mounting hardware.
SB-POL-RZG2/10TW3 INSTR_SKU# 011446


Specyfikacje produktu

Marka: JL Audio
Kategoria: Niesklasyfikowane
Model: Stealthbox SB-POL-RZG2/10TW3

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JL Audio Stealthbox SB-POL-RZG2/10TW3, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane JL Audio

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane