Instrukcja obsługi JL Audio Stealthbox SB-GM-HUMRH2/12W6v3/DG

JL Audio Niesklasyfikowane Stealthbox SB-GM-HUMRH2/12W6v3/DG

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JL Audio Stealthbox SB-GM-HUMRH2/12W6v3/DG (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

➔

Stealthbox®

I N S T A L L A T I O N G U I D E

SB - GM - H U M R2/1 2 W 6 v 2 , J L AU D I O , In c 2 0 0 4 Sh e e t S K U # 0 1 1 1 8 2 Re v i s i o n 8 / 5 / 2 00 4 Pag e 1

for the

SB-GM-HUMRH2/12W6v2

(2003-Up Hummer H2)

This Stealthbox is a product which

requires professional installation skills and

tools.

Please read this installation guide thor-

oughly before beginning the project. It

will guide you step by step through the

installation. Several of the steps in this

process may require two people to

accomplish.

It is absolutely vital that the enclosure

be properly mounted to the vehicle

according to these instructions. Failure

to mount the enclosure properly pres-

ents two problems: 1) The sub-bass

performance will suffer due to the

movement of the enclosure caused by

the force exerted by the woofer(s) and

2) A loose enclosure presents a serious

safety hazard in the event of a collision

or sudden deceleration.

Please enjoy your JL Audio Stealthbox

responsibly.

STEP 1:

Remove the third “jump” seat.

*STEPS 2-4 are for the vehicle that are

equip with the internal spare tire.*

STEP 2:

Remove the spare tire

STEP 3:

Remove the jack and jack tools.

STEP 4:

With an 8mm socket, remove the

four bolts that secure the spare tire rack.

STEP 5:

By pulling up, remove the driver’s

side rear storage bucket.

STEP 6:

With a 10mm socket, flat head

screw driver, Phillips® head screw driver and a

T-15 socket.

Remove the driver’s side rear wheel well plas-

tic trim.

START

HERE

Continued on Next Page ➔

w w w . j l a u d i o . c o m

➔

➔ ➔

➔➔➔

STEP 7: With the plastic trim out of the way,

remove the plastic inner wheel well.

STEP 11: Thread the supplied pair of socket ca

set screws into the enclosure, leaving 1/2” exposed.

Place the enclosure into place and firmly press

down.

Cont.

From

Page

Continued on Next Page ➔

➔

STEP 8: Rest the plastic inner wheel well on the

rear tire. Keep the trim and all the mounting hard-

ware together.

STEP 12: *CAUTION*

Before drilling, make sure that you are not going to

be drilling into any gas lines, brake lines, transmission

lines, electrical wiring, transfer case(4x4 vehicles) or

anything else that might cause a reduction in your

weekly pay. Always wear eye protection when

drilling.

With the use of a 1/2” drill bit and drill. Drill out the

floor at the impression on the wax square.

➔

STEP 13: Remove the wax square sheets from the

mounting area.

STEP 14: Run speaker wire to the enclosure loca-

tion.

Also check the woofer for proper operation.

STEP 9: (Inside the vehicle) Cut and remove

the factory jute(sound deadening), from the

removed storage area, from STEP 5.

STEP 10: Place the supplied pair of wax sheets

into place.

Remember to remove the rear paper backing, from

the wax sheets.

SB - GM - H U M R2/1 2 W 6 v 2 , J L AUDIO, I n c 2 0 0 4 Sh e e t S K U # 0 1 1 1 8 2 Re v i s i o n 8 / 5 / 2 00 4 Page 2

w w w . j l a u d i o . c o m

➔ ➔

➔➔➔

STEP 15: Back out the socket cup set screws, that

was threaded in from STEP 11, to expose 1-1/4”.

Connect the speaker wire to the terminal and place

the enclosure into position.

STEP 19: With the spare tire rack placed into

position. Loosely tighten the lower factory bolts to

the lower mounting feet.

Cont.

From

Page

Continued on Next Page ➔

➔

STEP 16: (Outside the vehicle) Place the sup-

plied hardware in order onto the exposed socket

cup screw. If more exposed threads are needed, back

out the socket cup set screws.

*Do not back out too much, you can cause a

conflict when mounting the plastic inner

wheel well, back into location.*

Fender washer, flat washer, lock washer and hex nut

onto each socket cup set screw.

Secure tightly.

STEP 20: Placed A supplied spacer, between each

upper mounting foot of the spare tire rack and the

side panel.

Loosely secure each upper mount assembly with a

supplied hex cap screw.

➔

STEP 21: Align the spare tire rack, for proper

positioning.

STEP 22: With the spare tire rack properly posi-

tioned, it should not interfere with the enclosure.

STEP 17: Mount the plastic inner wheel well and

plastic trim from STEPS 6 & 7.

You didn’t leave too much of the socket cup set

screws exposed, did you?

*STEPS 18-24 are for only for the vehicles

that are equip with the internal spare tire.*

STEP 18: The spare tire rack needs to be modi-

fied for the proper spacing,This needs to be accom-

plished on both bottom mounting feet.

Measure 9/16” from the center of the factory

mounting hole, back. Mark and drill with the a 1/2”

drill bit or Uni-bit®.

SB - GM - H U M R2/1 2 W 6 v 2 , J L AU D I O , I n c 2 0 0 4 Sh e e t S K U # 0 1 1 1 8 2 Re v i s i o n 8 / 5 / 2 00 4

Page 3

w w w . j l a u d i o . c o m

Specyfikacje produktu

Marka:	JL Audio
Kategoria:	Niesklasyfikowane
Model:	Stealthbox SB-GM-HUMRH2/12W6v3/DG

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JL Audio Stealthbox SB-GM-HUMRH2/12W6v3/DG, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane JL Audio

JL Audio MediaMaster 55-HR Instrukcja

7 Października 2024

JL Audio MediaMaster 55 Instrukcja

7 Października 2024

JL Audio Stealthbox SB-J-JL4DPAS/10TW1-2 Instrukcja

4 Października 2024

JL Audio MBT-RX Instrukcja

3 Października 2024

JL Audio MediaMaster MM105-HR Instrukcja

2 Października 2024

JL Audio JLINK RX Instrukcja

30 Września 2024

JL Audio Stealthbox SB-POL-RZG3/10TW3 Instrukcja

29 Września 2024

JL Audio Stealthbox SBA-J-JK-FHB Instrukcja

27 Września 2024

JL Audio Stealthbox SB-GM-BURBCNSL/10W3v3 Instrukcja

27 Września 2024

JL Audio Stealthbox SB-F-SUPRDTY/10W1v3 Instrukcja

27 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024