Instrukcja obsługi JL Audio Stealthbox SB-GM-ESC/10W1v3/DG

JL Audio Niesklasyfikowane Stealthbox SB-GM-ESC/10W1v3/DG

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JL Audio Stealthbox SB-GM-ESC/10W1v3/DG (3 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper installation, your new vehicle-

specific enclosed subwoofer system will deliver years of listening pleasure.

We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio dealer. The installation

professionals employed by your dealer have the necessary tools and experience to disassemble and reassemble your vehicle

properly. Also, keep in mind that your warranty coverage extends to 2 years if your system is installed or approved by your

authorized JL Audio dealer. If you prefer to perform your own installation, please read this installation guide completely

before beginning the process.

If you choose to perform the installation yourself, it is absolutely vital that

the Stealthbox® be properly mounted to the vehicle according to these

instructions. Failure to mount the enclosure properly presents two problems:

1) The sub-bass performance will suffer due to the movement of the enclosure

caused by the force exerted by the woofer(s).

2) A loose enclosure presents a serious safety hazard in the event of a collision

or sudden deceleration.

S T E P 1

These instructions are for both the short and long

wheelbase versions of this popular SUV.

Empty out the back of the vehicle so that you have a clean

area to work in.

Remove the pocket in the rear quarter interior trim panel on

the drivers side of the vehicle by pulling it up and out. The

wire to power the Stealthbox® needs to come from this open

area, now would be a good time to run that wire. Leave

enough extra to make it easy to make the connection to the

Stealthbox® before it is permanently mounted.

Continued on Next Page

S T E P 2

Looking down through the hole where the pocket had been,

notice the three studs installed at the factory. These studs

will be used to hold down the enclosure.

S T E P 3

The Triangular Plate will be positioned as shown with center

the hole closest to the stud pointing towards the center of

the vehicle..

SB-GM-ESC(ESV)/10W1v3 INSTR_SKU# 011303

INSTALLATION

D I F F I C U L T Y :

OUT

ESTIMATED TIME:

2 HOURS

I N S T A L L A T I O N G U I D E

for the

SB-GM-ESCESV/10W1v3

SB-GM-ESC/10W1v3

SKU#94476-94479 & 94483-94486

2007-2013 Cadillac Escalade, Chevrolet Tahoe/Suburban, & GMC Yukon

Continued on Next Page

SB-GM-ESC(ESV)/10W1v3 INSTR_SKU# 011303

S T E P 7

Remove the upper rear quarter window trim molding.

S T E P 6

Remove the two woofers from the Stealthbox® and, set it

into place, with the extension going into the previous pocket

location.

Inside the Stealthbox®, where the arrow points, use a small

marker to mark the interior panel where the hole in the

enclosure wall lies.

Remove the Stealthbox®

S T E P 5

Install the Triangular Plate as shown, tighten down the

fasteners that secure the Triangular Plate, leave only the large

Flat washer on top of the Hex nut, Split Lock Washer and

3/8-16 x 1-3/4” Hex Head Bolt. The remaining Flat Washer,

Split Lock Washer and Hex Nut will be installed inside the

enclosure.

S T E P 4

This is a side view of the Bracket shown in STEP 3 with the

included hardware shown for illustration purposes. Install

the 3/8-16 x 1-3/4” Hex Head Bolt through the Triangular

Plate as shown, tighten the Hex Nut that the arrow points

towards. The hardware shown to the left of the 3/8 x 2”

Fender Washer will be inside the Stealthbox® once the

installation is complete.

Page 2 • JL Audio, Inc 2014

S T E P 9

Drill the mark made in enlarge the hole to 1/2 inch. STEP 6,

****CAUTION****

Before drilling, always make sure that you are not

going to be drilling into any gas lines, brake lines,

tires, transmission lines, electrical wiring, exhaust

systems or anything else that might cause a

reduction in your weekly pay.

Always wear eye protection when drilling!

S T E P 1 1

Bolt the bottom hole of the Custom Bracket to the rear

pillar through the hole where the wiring harness had been

secured (see STEP 8). Slide the supplied 3/8-16 Speed Nut

onto the Custom Bracket as shown, align the hole in the

Custom Bracket with the hole in the rear quarter trim panel.

S T E P 1 0

The 1/4” hardware will be installed in the order as shown as

the custom bracket is installed in the vehicle.

NOTE: The arrow points to the upper end of the bracket.

S T E P 8

The upper mount for the lift arm for the tailgate must be

disconnected as shown in order to remove the trim panel.

The wiring harness that runs along the rear pillar has a white

plastic plug (see arrow) that pushes through a hole in the

pillar to locate it. Pull the plug as this hole will be used to

secure the lower end of the Custom Bracket shown in

STEP 10.

SB-GM-ESC(ESV)/10W1v3 INSTR_SKU# 011303

S T E P 1 5

Install the mounting 3/8-16 x 1 3/4” Hex Head Bolt, Split Lock

Washer and Flat Washer through the enclosure wall into the

Speed Nut shown in STEP 11. Also install the Hex Nut, Split

Lock Washer and, Flat Washer on the stud that protrudes

into the bottom of the Stealthbox® from the Triangular

Plate installed in STEP 5. Re-install the woofers into the

Stealthbox®.

C O N G R A T U L A T I O N S !

You have completed the installation for this model!

Enjoy your new Stealthbox®! Please refer to the Power

Recommendation section for an amplifier recommendation

and basic set-up help.

D E T A I L

One way to get the Hex Head Bolt and Flat Washer installed

from the inside of the rear pillar out is to tape them to a

wrench and then guide them through the recently drilled

hole. Once this hardware is in place, tighten all of the

hardware that secures the Custom Bracket in location. With

the Custom Bracket securely installed, replace the upper rear

quarter window trim molding that was removed in STEP 7.

Connect the speaker cables from the amplifier and set the

Stealthbox® in place.

S T E P 1 3

From inside the rear pillar, feed the 1/4-20 x 1” Hex Head Bolt

and 1/4” Flat Washer through the hole drilled in STEP 12 as

shown.

A suggestion on how to get the hardware through the hole

and held in place is shown below.

S T E P 1 2

With the bottom of the Custom Bracket bolted in and

aligned as described in drill a hole through the Step 11

pillar corresponding with the upper hole in the Custom

Bracket as shown.

****CAUTION****

Before drilling, always make sure that you are not

going to be drilling into any gas lines, brake lines,

tires, transmission lines, electrical wiring, exhaust

systems or anything else that might cause a

reduction in your weekly pay. Always wear eye

protection when drilling!

Page 3 • JL Audio, Inc 2014

All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered

trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.

#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.

(954) 443-1100

w w w . j l a u d i o . c o m

1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A

I N C L U D E D H A R D W A R E

1) Triangular Plate 1) Custom Bracket

4) 1/4” Flat Washer 3/8” Split Lock Washer3)

2) 1/4-20 x 1” Hex Head Bolt 1/4” Split Lock Washer2)

2) 3/8-16 x 1 3/4” Hex Head Bolt 3/8-16 Hex Nut2)

2) 1/4-20 Speed Nut 1/4-20 x 1” Hex Head Bolt2)

2) 3/8 x 1-1/4” Fender Washer 3/8 x 2” Fender Washer2)

S P E C I F I C A T I O N S

Enclosure Type: Acoustic Suspension (sealed)

Driver Type: (2) 10W1v3-4

Nominal Impedance: 4Ohms per woofer, 2Ohm final load

Continuous Power Handling: 600 Watts

P O W E R R E C O M M E N D A T I O N

JL Audio recommends high quality amplifiers such as the JL Audio HD900/5, 600/1v3, XD600/1 or JX 500/1. The

diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 600/1v3. If

another amplifier is being used, please reference this illustration and use similar settings on that amplifier.

All JL Audio amplifiers are very versatile audio components. Please consult the owner’s manual for even more

detailed information about installing and tuning your amplifier.

C O N N E C T I O N S

Using quality power, signal and speaker wire is essential in ensuring the performance of your Stealthbox®.

JL Audio recommends using a 4 AWG power kit such as the XC-PCS4-1B for your Stealthbox® amplifier, other

kits are available should you be using more than one amplifier. Signal wire such as the JL Audio Premium

Audio Interconnect Cables should be used that will provide signal for both channels of the amplifier. JL Audio

reccommends using 12AWG speaker wire for subwoofers such as our XC-BCS12-25.

M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T

A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.

Front Speaker Size / Location: 6-1/2”- Front Doors

Fits JL Audio Models: TR650-CXi, C2-650x, C3-650, C5-650, C5-650x & ZR650-CSi

Rear Speaker Size / Location: 6-1/2”- Rear Door

Fits JL Audio Models: TR650-CXi, C2-650x, C3-650, C5-650, C5-650x & ZR650-CSi

Specyfikacje produktu

Marka:	JL Audio
Kategoria:	Niesklasyfikowane
Model:	Stealthbox SB-GM-ESC/10W1v3/DG

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JL Audio Stealthbox SB-GM-ESC/10W1v3/DG, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane JL Audio

JL Audio MediaMaster 55-HR Instrukcja

7 Października 2024

JL Audio MediaMaster 55 Instrukcja

7 Października 2024

JL Audio Stealthbox SB-J-JL4DPAS/10TW1-2 Instrukcja

4 Października 2024

JL Audio MBT-RX Instrukcja

3 Października 2024

JL Audio MediaMaster MM105-HR Instrukcja

2 Października 2024

JL Audio JLINK RX Instrukcja

30 Września 2024

JL Audio Stealthbox SB-POL-RZG3/10TW3 Instrukcja

29 Września 2024

JL Audio Stealthbox SBA-J-JK-FHB Instrukcja

27 Września 2024

JL Audio Stealthbox SB-GM-BURBCNSL/10W3v3 Instrukcja

27 Września 2024

JL Audio Stealthbox SB-F-SUPRDTY/10W1v3 Instrukcja

27 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024