Instrukcja obsługi JL Audio Stealthbox SB-GM-BURBCNSL/10W3v3

JL Audio Niesklasyfikowane Stealthbox SB-GM-BURBCNSL/10W3v3

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JL Audio Stealthbox SB-GM-BURBCNSL/10W3v3 (8 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

➔

Stealthbox®

I N S T A L L A T I O N G U I D E

SB - G M -B U RB C NSL / 1 0 W3 v 2 , J L AU D I O , I n c 2 0 0 5 Sh e e t SK U # 0 1 1 1 6 7 3 /0 8 / 2 0 0 5Pag e 1

for the

SB-GM-BURBSCNSL/10W3v2

(2003-Up Chevrolet Suburban,Tahoe,

Silverado &

GMC Yukon,YukonXL, Sierra with front

bucket seats and center console)

This Stealthbox is a product which

requires professional installation skills and

tools.

Please read this installation guide thor-

oughly before beginning the project. It

will guide you step by step through the

installation. Several of the steps in this

process may require two people to

accomplish.

It is absolutely vital that the enclosure

be properly mounted to the vehicle

according to these instructions. Failure

to mount the enclosure properly pres-

ents two problems: 1) The sub-bass

performance will suffer due to the

movement of the enclosure caused by

the force exerted by the woofer(s) and

2) A loose enclosure presents a serious

safety hazard in the event of a collision

or sudden deceleration.

Please enjoy your JL Audio Stealthbox

responsibly.

Read the instructions completely, before the start of

the install.

This Stealthbox Enclosure install does require per-

manent modification to the OEM inner console.

STEP 1: Engage the emergency brake.

Place the key into the ignition and turn to the accessory posi-

tion.

The shifter and the steering wheel needs to be posi-

tioned all the way down.

Remove the front dash cluster panel, by pulling the dash trim

towards you and work around the diameter. Be careful not to

damage the four way light push button, located on top of the

steering column.

Once the trim is removed. Place the transmission into park,

remove the key from the ignition and pop the emergency brake.

STEP 2: Moving down to the top portion of the

center console. Pull the upper storage pocket panel

out and disconnect the electrical outlets.

STEP 3: Pull the cup holders up and out of the

center console.

STEP 4: On the upper lip of the main storage

bucket, remove all the screws, including the storage

lid’s screws.

STEP 5: To remove the main storage bucket,

remove the rubber mat.This will expose the four

screws that need to be removed.

Once all these screws have been removed. Remove

the storage bucket by lifting up and out of the con-

sole.

START

HERE

Continued on Next Page ➔

w w w . j l a u d i o . c o m

➔

➔ ➔

➔ ➔ ➔

STEP 6: To remove the front bucket seats, you

use a 15mm socket(not supplied) for the front nuts

and a 12mm(not supplied) for the rear bolts.

Tilt the seats backward to access and discon-

nect the wiring.This does include the air bag

wire.

STEP 10: To remove the OEM console, lift up on

the rear of the console and pull it back away from

the dash.

Cont.

From

Page

Continued on Next Page ➔

➔

STEP 7: Once the front seats have been

removed, you will need to outline the outside of

the center console with masking tape(not supplied).

This will help in future steps.

STEP 11: *TRUCKS ONLY*

With the console out, there is duct work that is exposed from under the dash. Remove the plastic duct that is attached to

the upper duct work. With the lower duct piece removed, it now exposes a door.

Insert the key into the ignition, turn to the accessory position, turn on the A/C. When the A/C is turned on, this willalloe the

exposed door to open.

This door is opened by a C-bracket that comes down from the upper dash.This C-bracket needs to be removed. If this

bracket is not removed, the A/C air flow will be not be correct.

This C-bracket is attached to the door and a motor that us located in the upper dash. Push the C-bracket to the passenger

side of the truck.This will detach the bracket from the door.With the C-bracket in hand, reach up as far up on the bracket

and push towards the passenger side of the truck.This will detach the C-bracket from the motor. Give the C-bracket to the

owner of the truck or store inside the truck for safe keeping.This bar will need to be reinstalled, If the Stealthbox is removed

and air flow is needed to the rear vents.

Use a small screw(not supplied) to hold this door shut. If this door is not screwed shut, air will blow on the driver’s feet and

reduce pressure from the dash vents.

➔

STEP 8: With the upper storage pocket panel

removed.You can view a pair of bolts. Using a 10mm

socket(not supplied), remove these bolts.

If you have not removed th front seats, there are

other bolts and screws that need to be located and

removed.This is to allow the console to be removed

out of the vehicle.

STEP 9: Look down in the console from the cup

holder area.You need to locate and disconnect a

white connection plug. Pull the lever on this white

connection plug to disconnect from the wire har-

ness..

SB - G M -B U RB C N S L /1 0 W 3 v 2 , J L AU D IO, I n c 2 0 0 5 Sh e e t SK U # 0 1 1 1 6 7 3 /0 8 / 2 0 0 5Pag e 2

w w w . j l a u d i o . c o m

*WARNING*

If you have removed the front seats, you need to place

both front seats back into the vehicle and reconnect the

wires from . Do not secure the seats back toSTEP 6

the floor.

Reconnect the ground wire to the negative side of the

battery.

Follow next step (STEP 11) and then repeat procedure

to remove the front seats. (caution before STEP 6)

*CAUTION*

The vehicle that you are working on might be

equipped with side impact air bags.To remove the

front seats, please follow these required procedures.

1)Disconnect the ground wire from the negative

side of the battery.

2)Let the vehicle sit for 15 minutes.This allows the

air bags to discharge.

3)Now you can remove the front seats and discon-

nect the air bag wire.

If you are not comfortable with disconnecting the air

bag wires.This install can be accomplished by not

removing the front seats. It will be tight quarters.

*Trucks* If you remove the front seats, you will

have to place the seats back in and reconnect the

air bag wires.Then repeat the removal process, in

future steps. You might not want to remove the

seats till then.

➔ ➔

➔➔➔

STEP 14: With the OEM carpet and the

jute(sound deadening) cut out. Position the supplied

pair of 3”x3” wax squares in place.

Make sure that the wax square is placed and with

the adhesive down and positioned as in the picture.

STEP 18: The wire harness from STEP 12 needs

to be rerouted over to the other side of the struc-

ture support bar under the dash.

Also at this time, run the speaker wire form the

amplifier location to the Stealthbox location.

Double check the woofer for correct functioning.

Cont.

From

Page

Continued on Next Page ➔

➔

STEP 15: Thread the supplied pair of socket cup

set screws into the Stealthbox. Leaving about 1/4”

exposed.

Position the Stealthbox into the mounting location

and firmly press down.

The Stealthbox is molded to mirror the floor. It

should tuck right in.

STEP 19: With the wire harness properly tucked

under the carpet, use double sided tape(not sup-

plied) to secure the carpet to the metal floor.

If the carpet is not secured to the floor, it will bunch

up after the OEM console is reinstalled.

Remove the masking tape that outlined the OEM

console from STEP2.

➔

STEP 16: When the Stealthbox is removed, the

wax square should have the impressions of the

socket cup set screws.

STEP 17: *CAUTION*

Before drilling, make sure that you are not going to

be drilling into any gas lines, brake lines, transmission

lines, electrical wiring, transfer case(4x4 vehicles) or

anything else that might cause a reduction in your

weekly pay. Always wear eye protection when

drilling.

With the use of a 1/2” drill bit and drill. Drill out the

floor at the’ impressions on the wax squares.

SB - G M -B U RB C N S L /1 0 W 3 v 2 , J L AU D I O, I n c 2 0 0 5 Sh e e t SK U #0 1 1 1 6 7 3 / 0 8 / 2 0 0 5Pag e 3

w w w . j l a u d i o . c o m

STEP 12: Remove the OEM wire harness from

the plastic track. Wrap the OEM wiring in black

tape.

STEP 13: With the OEM wiring harness out of

the way, you need to cut the carpet.

SIDES: From the tape outline of the center con

sole, measure inward to middle of the transmission

tunnel 1.5” from the tape. Mark and cut, front to

back.

FRONT: Cut left to right at the front area where

the outline starts to taper inward.

REAR: Feel for the black plastic mounting bracket.

Cut left to right at the transmission tunnel, behind

the black plastic mounting bracket.View picture.

Specyfikacje produktu

Marka:	JL Audio
Kategoria:	Niesklasyfikowane
Model:	Stealthbox SB-GM-BURBCNSL/10W3v3

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JL Audio Stealthbox SB-GM-BURBCNSL/10W3v3, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane JL Audio

JL Audio MediaMaster 55-HR Instrukcja

7 Października 2024

JL Audio MediaMaster 55 Instrukcja

7 Października 2024

JL Audio Stealthbox SB-J-JL4DPAS/10TW1-2 Instrukcja

4 Października 2024

JL Audio MBT-RX Instrukcja

3 Października 2024

JL Audio MediaMaster MM105-HR Instrukcja

2 Października 2024

JL Audio JLINK RX Instrukcja

30 Września 2024

JL Audio Stealthbox SB-POL-RZG3/10TW3 Instrukcja

29 Września 2024

JL Audio Stealthbox SBA-J-JK-FHB Instrukcja

27 Września 2024

JL Audio Stealthbox SB-GM-BURBCNSL/10W3v3 Instrukcja

27 Września 2024

JL Audio Stealthbox SB-F-SUPRDTY/10W1v3 Instrukcja

27 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024