Instrukcja obsługi JL Audio Stealthbox SB-F-EXPED/10W1v3

JL Audio Niesklasyfikowane Stealthbox SB-F-EXPED/10W1v3

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JL Audio Stealthbox SB-F-EXPED/10W1v3 (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

➔

Stealthbox®

I N S T A L L A T I O N G U I D E

SB - F -EXPED / 1 0 W 6 A E , J L AU D I O , In c 2 0 0 4 Sh e e t S K U # 0 1 1 1 0 6 Re v i s io n 6 /2 9 / 2 0 0 4 Pag e 1

for the

SB-F-EXPED/10W6AE

(1997-2002 Ford Expedition &

1998-2002 Lincoln Navigator)

This Stealthbox is a product which

requires professional installation skills and

tools.

Please read this installation guide thor-

oughly before beginning the project. It

will guide you step by step through the

installation. Several of the steps in this

process may require two people to

accomplish.

It is absolutely vital that the enclosure

be properly mounted to the vehicle

according to these instructions. Failure

to mount the enclosure properly pres-

ents two problems: 1) The sub-bass

performance will suffer due to the

movement of the enclosure caused by

the force exerted by the woofer(s) and

2) A loose enclosure presents a serious

safety hazard in the event of a collision

or sudden deceleration.

Please enjoy your JL Audio Stealthbox

responsibly.

STEP 1:

Remove the tool access panel, from

the passenger’s side rear cargo panel.

Remove all contents.

STEP 2:

Remove the hatch floor sill.

STEP 3:

Remove the cargo hatch ceiling trim.

STEP 4:

Unscrew the pair of cargo net

hooks, from the passenger’ side cargo panel.

STEP 5:

Remove the D-pillar trim.This is the

panel that is directly behind the passenger’s

rear side window.

STEP 6:

Remove the rear passenger’s side

door sill.

START

HERE

Continued on Next Page ➔

w w w . j l a u d i o . c o m

➔

➔ ➔

➔➔➔

STEP 7: Fold the rear seats forward and remove

the exposed floor trim panel.

STEP 11: Remove the rubber weather seal from

the rear passenger’s door opening.

Cont.

From

Page

Continued on Next Page ➔

➔

STEP 8: At the rear passenger’s side C-pillar. Lift

the flap covering the upper seat bolt anchor to

expose the mounting bolt.The flap needs to be lift-

ed from the bottom.

STEP 12: Remove the plastic trim off the rear pas-

senger’s side C-Pillar.This is located behind the pas-

senger’s side rear door, in front of the passenger’s

side rear side window.

➔

STEP 13: Remove the large passenger’s side rear

cargo panel.

STEP 14: Using an 8mm socket, remove the pair

of bolts that secures the tool kit partition.

If the vehicle is equipped with the OEM woofer sys-

tem, also remove at this time.

STEP 9: Using a 15mm socket, remove the

mounting bolt of the upper seat belt anchor.

STEP 10: At the bottom of this seat belt assembly,

lift up on the rubber boot cover.

Use a T-45 socket to remove this lower seat belt

anchor mounting bolt.

SB - F -EXPED / 1 0 W 6 A E , J L AU D I O, I n c 2 0 0 4 Sh e e t S K U # 0 1 1 1 0 6 Re v i s io n 6 / 2 9 / 2 0 0 4 Pag e 2

w w w . j l a u d i o . c o m

➔ ➔

➔➔➔

STEP 15: Using a razor knife, you need to cut out

the rubber lining that covers the passenger’s side

rear wheel well.

The cut needs to run from the floor at rear of the

wheel well, over the wheel well forward to the C-

pillar and over to the outer sheet metal.

STEP 21: Remove the wax square and run speak-

er wire to the enclosures mounting location.Test

woofer for proper operation.Then connect the

speaker wire to the wire terminal found on the

enclosure.

Cont.

From

Page

Continued on Next Page ➔

➔

STEP 16: Place the supplied wax square with the

paper removed and sticky side down, in the mount-

ing location of the threaded insert inside the enclo-

sure.

STEALTHBOX WALL THREADED INSERT

VEHICLE SHEET METAL

FENDER WASHER SOCKET CUP SET SCREW

LOCK WASHER

FLAT WASHER

HEX NUT

STEP 22: Back out the socket cup set screw to

expose 1-1/2”. Place the enclosure into location,

guiding the socket cup set screw through the drilled

hole.

STEP 23: In these steps, place the supplied fender

washer, flat washer, lock washer and then hex nut

onto the socket cup set screw.

If necessary , back out or in the socket cup set

screw for proper length. Use the least amount of

length.

➔

STEP 24: With an 8mm socket, mount the tool kit

partition that was removed in STEP 14.

STEP 25: Outside the vehicle, flip over the large

cargo panel that was removed in STEP 13.

Remove the clips from the edge of the storage

pocket.

If your Expedition/Navigator is equipped with the

OEM woofer system.You will need this storage

pocket trim from an Expedition(only) that does not

have the OEM woofer system. Check your Ford

Parts Department or local vehicle recycling yard.

STEP 17: Thread in the supplied socket cup set

screw into the enclosure. Allow 1/2” to be exposed.

STEP 18: Place the enclosure into the mounting

location and press firmly down.This to leave an

impression on the wax square from STEP 16.

STEP 19: Remove the enclosure, making sure that

the wax square does stay on the floor.

STEP 20: *CAUTION*

Before drilling, check under the vehicle for

fuel lines, brake lines, exhaust pipes, electri-

cal wiring or any other objects that present

a hazard.Always wear eye protection when

drilling

With a drill and a 1/2” drill bit, drill at the impression

on the wax square as a guide.

SB - F -EXPED / 1 0 W 6 A E , J L AU D I O, I n c 2 0 0 3 S h e e t S K U # 0 1 1 1 0 6 R e v i sio n 6 / 2 9 /2 0 0 4 Pag e 3

w w w . j l a u d i o . c o m

Specyfikacje produktu

Marka:	JL Audio
Kategoria:	Niesklasyfikowane
Model:	Stealthbox SB-F-EXPED/10W1v3

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JL Audio Stealthbox SB-F-EXPED/10W1v3, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane JL Audio

JL Audio MediaMaster 55-HR Instrukcja

7 Października 2024

JL Audio MediaMaster 55 Instrukcja

7 Października 2024

JL Audio Stealthbox SB-J-JL4DPAS/10TW1-2 Instrukcja

4 Października 2024

JL Audio MBT-RX Instrukcja

3 Października 2024

JL Audio MediaMaster MM105-HR Instrukcja

2 Października 2024

JL Audio JLINK RX Instrukcja

30 Września 2024

JL Audio Stealthbox SB-POL-RZG3/10TW3 Instrukcja

29 Września 2024

JL Audio Stealthbox SBA-J-JK-FHB Instrukcja

27 Września 2024

JL Audio Stealthbox SB-GM-BURBCNSL/10W3v3 Instrukcja

27 Września 2024

JL Audio Stealthbox SB-F-SUPRDTY/10W1v3 Instrukcja

27 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024