Instrukcja obsługi JL Audio MicroSub+ ACP112LG-TW1
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JL Audio MicroSub+ ACP112LG-TW1 (8 stron) w kategorii subwoofer. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/8
Thank you for purchasing a JL Audio amplified subwoofer system for
your automotive sound system.
Your subwoofer system has been designed and manufactured to exacting
standards to provide high-quality sub-bass performance and years of
musical enjoyment in your vehicle. For maximum performance, we
highly recommend that you have your new subwoofer system installed
by an authorized JL Audio retailer. Your authorized retailer has the
necessary training, expertise and installation equipment to ensure
optimum performance from this product. Should you decide to install
your subwoofer system yourself, please take the time to read this manual
thoroughly so as to familiarize yourself with it installation requirements
and setup procedures.
If you have any questions regarding the instructions in this
manual or any aspect of your subwoofer system’s operation, please contact
your authorized JL Audio retailer for assistance. If you need further
assistance, please call the JL Audio Technical Support Department at
(954) 443-1100 during business hours.
OWNER’S MANUAL
MicroSub+ / PowerWedge+
Amplied Subwoofer Systems with DCD™ Amplier Technology
50
80
125100
200
Low-Pass
Filter Freq. (Hz )
Turn-On
Mode
Remote
Level
Control
Low-Level Inputs
High-Level
Inputs
FUSE
(30A)
(L ) (R)
Input
Sensitivity
Min. Max.
Signal | DC | Rem 0 | 180 deg.
+12 VDC GND Remote
Output
Polarity
Powe r Conn e ction s
Power
(green)
Protect
(red)
2 JL AUDIO®
INSTALLATION APPLICATIONS
The built-in amplifier used in this subwoofer
system is designed for operation in vehicles
with 12V, negative-ground electrical systems.
Using this product in systems with positive
ground and/or voltages other than 12V
may result in damage to the product and
will void the warranty. This product is not
certified or approved for use in aircraft.
INSTALLATION PROCEDURE/CONNECTIONS
All connections are located on the amplifier
panel of the enclosure. All connections are made
via RCA-type or quick-disconnect plugs, making it
easy to remove the enclosure quickly, anytime you
need additional space in your vehicle.
1. Disconnect the NEGATIVE battery post
connection and secure the disconnected
cable to prevent accidental reconnection
during installation. This is an essential
safety precaution during installation!
2. Run power wire from the battery location to
the amplifier’s “+12 VDC” connection, taking
care to route it in such a way that it will not be
damaged and will not interfere with vehicle
operation. 8 AWG is the recommended
power wire size for this amplifier.
3. An appropriate fuse at the main power
wire to the amplifier is vital for vehicle
safety. This fuse must be installed within 18
inches (45 cm) of the positive (+12V) battery
post connection. If this is the only device
connected to this main wire, use a 30A fuse.
Do not install the fuse until the power wire
has been securely connected to the amplifier.
4. Find a good, solid metal grounding point
close to the amplifier panel and connect the
negative power wire to it using appropriate
hardware. Use the same sized wire used
for the +12V connection, no longer than 36
inches (90 cm) from the amplifier’s ground
(GND) connector to the ground connection
point. 8 AWG is the recommended
ground wire size for this amplifier.
5. Run a wire from the source unit’s positive
(+12V) remote turn-on output to the
amplifier’s “Remote” connection. If your
source unit does not have a dedicated remote
turn-on output, you may elect to use one of
the automatic turn-on options, configured via
the amplifier’s “Turn-On Mode” switch. (See
“Control Panel Settings and Adjustments.”)
6. Signal Input (Low-Level): Connect the
amplifier’s RCA input jacks to the source
unit’s preamp level output jacks. You may
run a stereo or a mono signal into the
SAFETY CONSIDERATIONS
• Install this subwoofer system in a dry, well-
ventilated location that does not interfere
with your vehicle’s safety equipment (air bags,
seat belt systems, ABS brake systems, etc.).
• Securely mount the subwoofer system so
that it does not come loose in the event of
a collision or a sudden jolt to the vehicle.
• Check before drilling to make sure that you
will not be drilling into a gas tank, brake line,
wiring harness or other vital vehicle system.
• Do not run system wiring outside or
underneath the vehicle. This is an
extremely dangerous practice, which
can result in severe damage/injury.
• Protect all system wires from sharp edges by
carefully routing them, tying them down and
using grommets and loom where appropriate.
• Secure all wiring as needed, using cable
ties or wire clamps to protect them
from moving parts and sharp edges.
WHAT’S INCLUDED
(1) Enclosure with subwoofer(s), built-
in DCD™ amplifier and grille(s)
(1) Power Connection plug
(1) High-Level input plug
(1) Fuse
(1) User manual
PRODUCT DESCRIPTION
Enclosed subwoofer system with built-
in DCD™ Class D amplifier and specially
engineered, low-impedance driver(s).
ABOUT DCD™ TECHNOLOGY
JL Audio’s exclusive DCD™ amplifier technology
combines direct power conversion with an ultra-
high current output section and unique low-
impedance drivers to extract maximum power and
efficiency. By directly converting a vehicle’s 12V
supply into speaker power, DCD™ amplifiers are
free of traditional switching power supplies, thus
enabling them to be very compact, while generating
remarkable power output with unprecedented
efficiency (up to 94%). This also permits DCD™
amplifiers to operate at much cooler temperatures
than conventional amplifiers.
WARNING! DCD™ amplified subwoofer
systems use very specific components. Never
use a DCD™ amplifier or its companion
subwoofer(s) with incompatible, non-DCD™
products. Doing so will void the warranty
and may cause severe damage/injury.
MicroSub+ / PowerWedge+ with DCD™ Amplifier Technology 3
POWER CONNECTIONS PLUG
To connect the power wires and remote
turn-on wire to the amplifier, unplug the
“Power Connections” plug from the amplifier
panel (pull back firmly) and back out the set
screws on the connector plug using a Phillips
head screwdriver. Strip 3/8 inch (10 mm) of
insulation from the end of each wire and insert
the bare wire into the receptacle on the power
connector plug, seating it firmly so that no
bare wire is exposed. While holding each wire
in place, tighten each set screw firmly, taking
care not to strip the head of the screw.
Warning! Never make power connections with
a “live” wire. Always disconnect the negative
battery post before making any connections or
adjustments to a 12V power connection! Failure
to make safe, tight, high-integrity connections
can result in fire and extensive damage!
inputs of the amplifier. The amplifier’s
input section automatically sums stereo
signals to mono for the internal amplifier
section. When feeding a single, low-level
RCA input connection, use a Y-adaptor
splitter to split the mono signal and connect
it to both Left and Right RCA inputs.
7. Signal Input (High-Level): If your system
does not offer a preamp level signal option,
you can connect speaker level signals directly
to the “High-Level Inputs” connector using
the supplied 4-pin plug and wire harness.
Simply splice the appropriate left/right
and positive/negative wires to the included
harness, and plug the harness into the “High-
Level Inputs” connector on the amplifier. The
amplifier will attenuate the high-level signal
to make it compatible with its input stage.
Refer to the table below for corresponding
wire color information. Make sure to observe
correct polarity in making high-level input
connections. Failure to do so will result
in a loss of signal (poor performance).
8. Make necessary adjustments to the
input sensitivity and filter controls.
9. With the optional RBC-1 Remote Level
Control (sold separately), you can control
the amplifier’s output level from the
front of the vehicle. Connect the RBC-1
to the amplifier’s panel-mounted RJ11
input jack. (Refer to Appendix B)
Remote
Level
Control
Low-Level Inputs
High-Level
Inputs
FUSE
(30A)
(L ) (R)
+12 VDC GND Remote
Power Connections
Connection Description
Power
Connections
+ Positive (+12V) Power Connection+12 VDC
– GND Negative (GND) Ground Connection
R Remote Positive (+12V) Remote Turn-On Input
Low-Level Inputs
(RCA Jacks)
(L) White RCA Ch. 1 Input Left Channel Signal Input
(R) Red RCA Ch. 2 Input Right Channel Signal Input
High-Level Inputs
(4-Pin
Connector)
White
Ch. 1 Input
(+) Left Channel Positive
White/Black (–) Left Channel Negative
Gray
Ch. 2 Input
(+) Right Channel Positive
Gray/Black (–) Right Channel Negative
Remote Level Control RJ11 Input Jack for RBC-1 (sold separately)
Specyfikacje produktu
| Marka: | JL Audio |
| Kategoria: | subwoofer |
| Model: | MicroSub+ ACP112LG-TW1 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z JL Audio MicroSub+ ACP112LG-TW1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje subwoofer JL Audio
13 Października 2024
6 Października 2024
6 Października 2024
4 Października 2024
30 Września 2024
30 Września 2024
30 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
Instrukcje subwoofer
- subwoofer Yamaha
- subwoofer Pioneer
- subwoofer Bosch
- subwoofer JBL
- subwoofer Onkyo
- subwoofer Roland
- subwoofer Origin Acoustics
- subwoofer KEF
- subwoofer Bose
- subwoofer Klipsch
- subwoofer Crestron
- subwoofer Behringer
- subwoofer Boss
- subwoofer Marquant
- subwoofer Jensen
- subwoofer Blaupunkt
- subwoofer Speed-Link
- subwoofer Metra
- subwoofer Martin Logan
- subwoofer DAP-Audio
- subwoofer Denon
- subwoofer Phoenix Gold
- subwoofer Audac
- subwoofer Cambridge
- subwoofer Kenwood
- subwoofer Polk
- subwoofer Alpine
- subwoofer Dynaudio
- subwoofer Paradigm
- subwoofer JVC
- subwoofer Memphis Audio
- subwoofer Jamo
- subwoofer Auna
- subwoofer Nubert
- subwoofer LD Systems
- subwoofer Krüger&Matz
- subwoofer Audioengine
- subwoofer Audiotec Fischer
- subwoofer Clarion
- subwoofer Pro-Ject
- subwoofer Fusion
- subwoofer Neumann
- subwoofer Wharfedale
- subwoofer Magnat
- subwoofer Pyle
- subwoofer ELAC
- subwoofer Sonus Faber
- subwoofer Marantz
- subwoofer Bowers & Wilkins
- subwoofer Monitor Audio
- subwoofer Vonyx
- subwoofer Alto
- subwoofer Peavey
- subwoofer RCF
- subwoofer Harman Kardon
- subwoofer REL Acoustics
- subwoofer Teufel
- subwoofer Dali
- subwoofer Proel
- subwoofer Hifonics
- subwoofer Focal
- subwoofer Kicker
- subwoofer Omnitronic
- subwoofer Mackie
- subwoofer Deaf Bonce
- subwoofer Insignia
- subwoofer Piega
- subwoofer SVS
- subwoofer Arcam
- subwoofer Mac Audio
- subwoofer Infinity
- subwoofer McIntosh
- subwoofer Revel
- subwoofer Dynacord
- subwoofer Orion
- subwoofer Hertz
- subwoofer Kali Audio
- subwoofer KRK
- subwoofer Atlas Sound
- subwoofer Gemini
- subwoofer Martin
- subwoofer PMC
- subwoofer Definitive Technology
- subwoofer Ground Zero
- subwoofer Stinger
- subwoofer PowerBass
- subwoofer Power Dynamics
- subwoofer Kanto
- subwoofer Rockford Fosgate
- subwoofer Canton
- subwoofer Monacor
- subwoofer Tannoy
- subwoofer Electro-Voice
- subwoofer AudioControl
- subwoofer SPL
- subwoofer Crunch
- subwoofer Match
- subwoofer Indiana Line
- subwoofer HK Audio
- subwoofer Fenton
- subwoofer Sonance
- subwoofer Cabasse
- subwoofer Audison
- subwoofer Sonos
- subwoofer Musway
- subwoofer Renegade
- subwoofer Heco
- subwoofer MB Quart
- subwoofer Massive
- subwoofer Atlantic
- subwoofer QTX
- subwoofer QSC
- subwoofer Lanzar
- subwoofer Genelec
- subwoofer Apart
- subwoofer Bazooka
- subwoofer Skytec
- subwoofer Monoprice
- subwoofer Eve Audio
- subwoofer Yorkville
- subwoofer Axton
- subwoofer Nxg
- subwoofer FBT
- subwoofer OSD Audio
- subwoofer Andover
- subwoofer Soundstream
- subwoofer PSB
- subwoofer Citronic
- subwoofer James
- subwoofer PSSO
- subwoofer Quadral
- subwoofer Wet Sounds
- subwoofer Extron
- subwoofer BW
- subwoofer Helix
- subwoofer Mission
- subwoofer Martin Audio
- subwoofer Morel
- subwoofer Avid
- subwoofer Ecler
- subwoofer Mtx Audio
- subwoofer Aquatic AV
- subwoofer DB Technologies
- subwoofer GoldenEar Technology
- subwoofer Roswell
- subwoofer Velodyne
- subwoofer Chrysalis
- subwoofer Raveland
- subwoofer ANT
- subwoofer IMG Stage Line
- subwoofer Eikon
- subwoofer ESX
- subwoofer Wavemaster
- subwoofer Fluance
- subwoofer RetroSound
- subwoofer Pyramid
- subwoofer On-Q
- subwoofer Sound Ordnance
- subwoofer MadBoy
- subwoofer Planet Audio
- subwoofer Black Hydra
- subwoofer Totem
- subwoofer Energy
- subwoofer Mirage
- subwoofer Poly-Planar
- subwoofer SSV Works
- subwoofer PrecisionPower
- subwoofer Theater Solutions
- subwoofer Mordaunt Short
- subwoofer Triangle
- subwoofer Audiofrog
- subwoofer KLH Audio
- subwoofer Proficient
- subwoofer Alphasonik
- subwoofer Cerwin-Vega
- subwoofer BMB
- subwoofer Glemm
Najnowsze instrukcje dla subwoofer
13 Października 2024
10 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024