Instrukcja obsługi JL Audio MBT-CRXv2


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JL Audio MBT-CRXv2 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
Weatherproof Bluetooth® Controller / Receiver
Product Description
The MBT-CRXv2 is a water-resistant (IP67
rated) Bluetooth® receiver designed for
marine and powersports applications. It can
be used as a stand-alone Bluetooth® source
unit/receiver, connecting directly to an
amplifier. It can also be used as an add-on
Bluetooth® controller/receiver, connected
to an existing head unit’s line-level/auxiliary
inputs. The MBT-CRXv2 is not designed to
drive loudspeakers directly.
What’s Included
(1) MBT-CRXv2 Bluetooth
controller/receiver
(1) Threaded fastening collar
(1) Thin round gasket
(1) Thick round gasket
(1) Square adaptor plate
(1) Square adaptor gasket
(4) Stainless steel mounting screws
(1) User Manual
Installation Applications
This product is designed for operation in
12 volt, negative-ground electrical systems.
Using this product in systems with positive
ground and/or voltages other than 12 volts
may result in damage to the product and
will void the warranty. This product is not
certified or approved for use in aircraft.
Safety Considerations
Whenever possible, mount this product
in a dry, well-ventilated location that does
not interfere with other factory installed
electronic devices. If a dry environment is
not available, a location that is not exposed
to heavy splashing may be used.
While this product is designed to be water-
resistant, it should never be submerged
under water for prolonged periods or
subjected to high-pressure water spray.
Do not mount in an engine compartment
or in any areas of extreme heat.
Ensure this product is securely installed so
that it does not come loose in the event of a
collision/sudden jolt or as a result of repeated
vibrations during normal operation.
Check before drilling to make sure that you
will not be drilling into an exterior panel/
hull, fuel tank, gas/brake line, wiring harness,
or other vital system.
Do not run system wiring outside or
underneath the vehicle/vessel. This is an
extremely dangerous practice, which can
result in severe damage/injury.
Protect all system wires from sharp
edges (metal, fiberglass, etc.) by carefully
routing them, tying them down and using
grommets and loom where appropriate.
Secure all wiring as needed, using cable
ties or wire clamps to protect them from
moving parts and sharp edges.
Do not replace the power wire fuse with one
of a different value. Never bypass the fuse.
Mounting & Installation
The design of the MBT-CRXv2 requires just
a single hole for installation. Its easy-to-
use threaded-collar mounting system can
accommodate installations in flat surfaces up
to 1.75 inches (4.5 cm) thick. A front-mounted
adaptor plate is included for installations in
panels exceeding 1.75 inches (4.5 cm) thick,
or where rear access is limited or not possible.
Refer to the diagrams below for your specific
mounting application.
Standard Collar-Mount Installation
Front-Mount Adaptor Installation
IP67
WAT ER
RE SI ST ANT
MBT_CRX_MANv2-071018.indd 1 7/10/18 12:05 PM
Wiring Diagram
Pairing Your Device
(required for operation)
1. Ensure your streaming device has Bluetooth®
enabled and that the MBT-CRXv2 is on
(backlit in blue). The JL Audio logo on the
MBT-CRXv2 will blink to indicate it is in
pairing mode.
2. Within your streaming devices Bluetooth®
setup menu, select “MBT-CRXv2” from the list
of pairable devices.
3. When successfully connected, the
JL Audio logo on the MBT-CRXv2 will stop
blinking and remain lit. A single beep will be
heard through the connected audio system.
Note: If optional connection is made to a head
unit’s remote turn-on output, the head unit will
turn the MBT-CRXv2 on/off and the MBT-CRXv2
power button will no longer operate.
Pairing Considerations cont’d
When a connected streaming device is out
of range for more than one minute, the
MBT-CRXv2 will automatically disconnect this
streaming device and return to pairing mode
(JL Audio logo will blink). When that same
device comes back into range, it should be
reconnected to the MBT-CRXv2 manually.
Controlling Audio Playback
Once connected, use the controls on the
MBT-CRXv2 to adjust volume up/down, track
selection and play/pause.
IP67 Water Resistance Rating
This product has been tested to withstand immersion in water,
up to 1 meter (3.28 ft.) deep, for up to 30 minutes (when prop-
erly installed). Note - while designed to be water resistant, this
product should never be submerged under water for prolonged
periods or subjected to activity that creates pressure on it that
exceeds its depth rating.
2-Year Limited Warranty (U.S.A.)
Visit www.jlaudio.com for warranty details.
For Service Information in the U.S.A. please call JL Audio
customer service: (954) 443-1100 during normal business hours
(Eastern Time) • JL Audio, Inc • 10369 N Commerce Parkway,
Miramar, FL 33025
International Warranties:
Products purchased outside the United States of America are
covered only by that country’s distributor and not by JL Audio, Inc.
The Bluetootword mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and
any use of such marks by JL Audio, Inc. is under license. Qualcomm aptX is a product of Qualcomm
Technologies, Inc. and/or its subsidiaries. Qualcomm is a trademark of Qualcomm Incorporated,
registered in the United States and other countries. aptX is a trademark of Qualcomm Technologies
International, Ltd., registered in the United States and other countries and any use of such marks by
JL Audio, Inc. is under license.
071018 Printed in China
Pairing Considerations
Multiple devices can be paired to the
MBT-CRXv2, but only one streaming device
can connect at one time.
The MBT-CRXv2 will remember the last device
that was connected to it and reconnect with
it automatically. If that streaming device is not
active, then other paired streaming devices can
connect manually, or new streaming devices
can be paired.
Specifications
Bluetooth® Prole A2DP (High-Quality, Stereo Audio)
Bluetooth® Core
Specication
Version 4.0 with
Qualcomm® aptX™ audio
Frequency Response 20 Hz – 18 kHz (±1dB)
Outputs One Stereo Pair, Low-Level RCA Plugs
Output Voltage 2V RMS
Signal to Noise Ratio 93 dB (20 Hz – 20 kHz)
Input Operating Voltage 8 – 28 VDC
Current Draw 48 mA (at idle)
64 mA (at full output)
Remote Turn-on
Output Capacity 350 mA (max)
Fuse Rating 2A Mini ATC
Connection Range* Up to 35 ft / 11 m
*Maximum range is achieved in line-of-sight installations, actual range
will vary based on installation specics.
Control Legend
MBT_CRX_MANv2-071018.indd 2 7/10/18 12:05 PM


Specyfikacje produktu

Marka: JL Audio
Kategoria: Niesklasyfikowane
Model: MBT-CRXv2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JL Audio MBT-CRXv2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane JL Audio

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024